Home
last modified time | relevance | path

Searched full:defaults (Results 1 – 25 of 215) sorted by relevance

123456789

/Zephyr-Core-3.4.0/dts/bindings/sensor/
Dnxp,fxas21002-common.yaml13 This pin defaults to active low when consumed by the sensor.
21 This pin defaults to active low when produced by the sensor.
29 This pin defaults to active low when produced by the sensor.
Dst,iis2iclx-common.yaml11 This pin defaults to active high when produced by the sensor.
25 mandatory and if not present it defaults to 1 which is the
Dst,hts221-common.yaml11 This pin defaults to active high when produced by the sensor.
Dadi,adt7310.yaml11 The INT signal defaults to active low open drain, so requires a
Dbosch,bmi160.yaml13 Zephyr driver maps all interrupts to INT1. The signal defaults
Dbosch,bmi323.yaml13 Zephyr driver maps all interrupts to INT1. The signal defaults
Dnxp,fxos8700-common.yaml13 This pin defaults to active high when consumed by the sensor.
21 This pin defaults to active low when produced by the sensor.
29 This pin defaults to active low when produced by the sensor.
Dst,ism330dhcx-common.yaml12 This pin defaults to active high when produced by the sensor.
28 mandatory and if not present it defaults to 1 which is the
Dadi,adt7420.yaml14 The INT signal defaults to active low open drain, so requires a
Dst,iis2dh-i2c.yaml16 This pin defaults to active high when produced by the sensor.
Dst,iis2dh-spi.yaml16 This pin defaults to active high when produced by the sensor.
/Zephyr-Core-3.4.0/dts/bindings/display/
Dst,stm32-ltdc.yaml54 description: First pixel in x direction on layer 0. Defaults to 0.
58 description: Last pixel in x direction on layer 0. Defaults to width.
62 description: First pixel in y direction on layer 0. Defaults to 0.
66 description: Last pixel in y direction on layer 0. Defaults to height.
Dsolomon,ssd16xx-common.yaml57 defaults loaded from the controllers OTP memory.
60 has been specified. That profile may be empty to use the defaults
/Zephyr-Core-3.4.0/dts/bindings/mfd/
Dnordic,npm6001.yaml30 description: Input type for BUCK_MODE0 pin. Defaults IC boot-time value.
40 description: Input type for BUCK_MODE1 pin. Defaults IC boot-time value.
50 description: Input type for BUCK_MODE2 pin. Defaults IC boot-time value.
/Zephyr-Core-3.4.0/soc/riscv/riscv-privileged/andes_v5/
DKconfig.defconfig.series7 # SoC defaults should be parsed before SoC Series defaults, because SoCs usually
/Zephyr-Core-3.4.0/dts/bindings/kscan/
Dhynitron,cst816s.yaml14 The irq signal defaults to active low as produced by the
21 The reset signal defaults to active low to the
/Zephyr-Core-3.4.0/tests/drivers/regulator/voltage/dts/bindings/
Dtest-regulator-voltage.yaml38 Number of ADC readings to average. Defaults to 1 (no average).
44 Delay between voltage set and ADC read. Defaults to 0 (no delay).
/Zephyr-Core-3.4.0/samples/bluetooth/hci_uart/boards/
Dnrf9160dk_nrf52840.conf1 # Override prj.conf defaults
/Zephyr-Core-3.4.0/dts/bindings/sdhc/
Dnxp,imx-usdhc.yaml45 This pin defaults to active high when consumed by the SD card. The
53 This pin defaults to active low when produced by the SD card. The
/Zephyr-Core-3.4.0/dts/bindings/mipi-dsi/
Dst,stm32-mipi-dsi.yaml71 defaults to HAL_DSI_ERROR_NONE.
77 Defaults to 0 which disables the filter.
/Zephyr-Core-3.4.0/samples/posix/eventfd/
Dprj.conf7 # so provide reasonable defaults so it can be built.
/Zephyr-Core-3.4.0/samples/sensor/bme280/
DKconfig14 # the device connected either way. These defaults can be overridden if
/Zephyr-Core-3.4.0/samples/net/syslog_net/
DKconfig13 zero means that the defaults in the application are used.
/Zephyr-Core-3.4.0/dts/bindings/rtc/
Drtc-device.yaml14 alarms defaults to 0, which indicates that the RTC has
/Zephyr-Core-3.4.0/dts/bindings/spi/
Dmicrochip,xec-qmspi-ldma.yaml42 Defaults to 1 for full duplex driver's support for full-duplex spi.
52 Ports 1 and 2 implement CS0# only. Defaults to CS0#.

123456789