Searched full:connects (Results 1 – 25 of 118) sorted by relevance
12345
| /Zephyr-latest/dts/bindings/ethernet/ |
| D | infineon,xmc4xxx-ethernet.yaml | 62 If the RMII interface is used it connects GPIO to the rmii-clk signal.
63 Otherwise, if the MII interface is used, then it connects to the Receive clock (rx-clk)
75 If the RMII interface is used it connects GPIO to the Carrier Sense Data Valid (crs-dv)
76 signal. Otherwise, if the MII interface is used, it connects to the
|
| /Zephyr-latest/tests/bsim/bluetooth/host/privacy/central/src/ |
| D | main.c | 26 .test_descr = "Central connects to a peripheral using a short RPA timeout",
33 .test_descr = "Central connects to a peripheral using a short RPA timeout"
|
| /Zephyr-latest/dts/bindings/i2c/ |
| D | infineon,xmc4xxx-i2c.yaml | 61 Connects the I2C clock line (USIC DX1 input) to a specific GPIO pin.
62 The USIC DX1 input is a multiplexer which connects to different GPIO pins.
77 Connects the I2C data line (USIC DX0 input) to a specific GPIO pin.
78 The USIC DX0 input is a multiplexer which connects to different GPIO pins.
|
| /Zephyr-latest/tests/drivers/i2s/i2s_speed/ |
| D | Readme.txt | 7 This board uses CONFIG_I2S_TEST_SEPARATE_DEVICES=y and connects two SAI peripherals by shorting
|
| /Zephyr-latest/dts/bindings/can/ |
| D | infineon,xmc4xxx-can-node.yaml | 24 description: Connects the CAN input line to a specific IO.
|
| /Zephyr-latest/dts/bindings/serial/ |
| D | zephyr,uart-emul.yaml | 26 Connects TX to RX internally creating a loop back connection. Useful
|
| /Zephyr-latest/dts/bindings/spi/ |
| D | infineon,xmc4xxx-spi.yaml | 16 Connects the SPI miso line (USIC DX0 input) to a specific GPIO pin.
17 The USIC DX0 input is a multiplexer which connects to different GPIO pins.
|
| /Zephyr-latest/boards/adi/max32666evkit/doc/ |
| D | index.rst | 135 | | | | Close | | | Connects I2C0 SCL and SDA 1.5K pullups to VDDIOH. …
142 | | | | Close | | | Connects I2C1 SCL and SDA 1.5K pullups to VDDIOH. …
149 | | | | Close | | | Connects I2C2 SCL and SDA 1.5K pullups to VDDIOH. …
156 | | | | Close | | | Connects LED D2 to P1_14. …
163 | | | | Close | | | Connects LED D3 to P1_15. …
168 | | | | 2-1 | | | Connects VBUS to USB connector CN1 to supply board…
170 | | | | 2-3 | | | Connects VBUS to USB connector CN2 to supply board…
179 | | | P0_20 | | | 2-1 | | | Connects the USB to serial UART to GPIO P0_20 (RX1…
181 | | | P0_28 | | | 2-3 | | | Connects the USB to serial UART to GPIO P0_28 (RX2…
186 | | | P0_21 | | | 2-1 | | | Connects the USB to serial UART to GPIO P0_21 (TX1…
[all …]
|
| /Zephyr-latest/tests/bsim/bluetooth/ll/cis/tests_scripts/ |
| D | connected_iso_acl_first_ft_cen_skip_2_se.sh | 7 # Basic Connected ISO test: a Central connects to 1 Peripheral and tests RTN=2,
|
| D | connected_iso_acl_first_ft_cen_skip_4_se.sh | 7 # Basic Connected ISO test: a Central connects to 1 Peripheral and tests RTN=2,
|
| D | connected_iso_acl_first_ft_per_skip_2_se.sh | 7 # Basic Connected ISO test: a Central connects to 1 Peripheral and tests RTN=2,
|
| D | connected_iso_acl_first_ft_per_skip_4_se.sh | 7 # Basic Connected ISO test: a Central connects to 1 Peripheral and tests RTN=2,
|
| /Zephyr-latest/samples/bluetooth/peripheral_hr/ |
| D | README.rst | 12 connects it will generate dummy heart-rate values.
|
| /Zephyr-latest/tests/bsim/bluetooth/ll/advx/tests_scripts/ |
| D | basic_advx.sh | 7 # Basic connection test: a central connects to a peripheral and expects a
|
| D | basic_advx_scan_aux_use_chains.sh | 7 # Basic connection test: a central connects to a peripheral and expects a
|
| D | basic_advx_ticker_expire_info.sh | 7 # Basic connection test: a central connects to a peripheral and expects a
|
| /Zephyr-latest/tests/bsim/bluetooth/ll/conn/tests_scripts/ |
| D | basic_conn_encrypted_split.sh | 7 # Basic connection test: a central connects to a peripheral and expects a
|
| D | basic_conn_encrypted_split_privacy.sh | 7 # Basic connection test: a central connects to a peripheral and expects a
|
| D | basic_conn_encrypted_split_single_timer.sh | 7 # Basic connection test: a central connects to a peripheral and expects a
|
| D | basic_conn20_split.sh | 6 # Basic connection test: a central connects to a peripheral
|
| D | basic_conn_split.sh | 7 # Basic connection test: a central connects to a peripheral and expects a
|
| /Zephyr-latest/drivers/can/ |
| D | Kconfig.xmc4xxx | 35 Connects all XMC4XXX CAN devices to an internal bus. Enables
|
| /Zephyr-latest/tests/bsim/bluetooth/host/gatt/general/test_scripts/ |
| D | gatt.sh | 5 # Basic GATT test: A central acting as a GATT client scans for and connects
|
| /Zephyr-latest/samples/bluetooth/peripheral_nus/ |
| D | README.rst | 12 but it may be binary data. Once the user connects to the device and subscribes to the TX
|
| /Zephyr-latest/tests/bsim/bluetooth/ll/bis/tests_scripts/ |
| D | past_send_from_broadcaster.sh | 7 # Basic PAST Test: Broadcaster connects to peripheral, after connection is established
|
12345
