Home
last modified time | relevance | path

Searched full:cable (Results 1 – 25 of 172) sorted by relevance

1234567

/Zephyr-latest/dts/bindings/dsa/
Dmicrochip,ksz8794.yaml16 0x01: Short Cable Problems with the KSZ8795 Family
17 0x02: 1) CAT-5E/6 Short Cable with a Link Issue for the KSZ8795 Family
18 0x04: 2) CAT-5E/6 Short Cable with a Link Issue for the KSZ8795 Family
/Zephyr-latest/doc/connectivity/networking/api/
Dethernet_mgmt.rst20 device driver when it notices that the Ethernet cable is disconnected.
22 notices that the Ethernet cable is re-connected.
/Zephyr-latest/drivers/ethernet/
Ddsa_ksz8xxx.c348 * Solution for Short Cable Problems with the KSZ8795 Family
351 * Solution for Short Cable Problems with the KSZ8795 Family
353 * https://microchipsupport.force.com/s/article/Solution-for-Short-Cable-
358 * type of short cable (<3m).
365 * equalizer EQ that can balance the signal received to adapt various cable
368 * When using some type of short cable (for example, CAT-6 cable with low
369 * attenuation to high frequencies signal vs. CAT-5 cable) or board to board
410 * to the different type of short cable’s characteristics. The current default
414 * for all corner cases of the short cable and short distance connection for
432 * Solution for Using CAT-5E or CAT-6 Short Cable with a Link Issue for the
[all …]
/Zephyr-latest/boards/raspberrypi/rpi_5/doc/
Dindex.rst107 * JST cable: 3-pin JST connector to 3-pin JST connector cable
108 * USB cable: USB A male - Micro USB B male
110 Use the JST cable to connect the Raspberry Pi Debug Probe UART port to the Raspberry Pi 5 UART port…
112 Then connect the Raspberry Pi Debug Probe to your computer with a USB cable.
/Zephyr-latest/samples/sensor/tmp116/
DREADME.rst37 In order to build the sample, connect the board to the computer with a USB cable and enter the
48 The output can be seen via a terminal emulator (e.g. minicom). Connect the board with a USB cable
/Zephyr-latest/samples/drivers/video/tcpserversink/
DREADME.rst25 J35 camera connector. A USB cable should be connected from a host to the micro
27 interface. Ethernet cable must be connected to RJ45 connector.
/Zephyr-latest/doc/connectivity/networking/
Dusbnet_setup.rst13 The board is connected to Linux host using USB cable
17 Linux host using a USB cable providing an Ethernet interface to the host.
25 After plugging a USB cable from the board to the Linux host, the
/Zephyr-latest/dts/bindings/gpio/
Dnxp,i2c-tsc-fpc.yaml9 exposed on a 6 pin flexible printed cable connector. The pins have the
Dnxp,parallel-lcd-connector.yaml9 exposed on a 40 pin flexible printed cable connector. The pins have the
/Zephyr-latest/boards/shields/frdm_kw41z/doc/
Dindex.rst39 #. Connect the FRDM-KW41Z board to your computer with a USB cable. A USB mass
44 #. Remove the USB cable to power down the board.
/Zephyr-latest/boards/snps/em_starterkit/support/
Dopenocd.cfg1 # Configure JTAG cable
/Zephyr-latest/boards/snps/iotdk/support/
Dopenocd.cfg9 # Configure JTAG cable
/Zephyr-latest/boards/snps/emsdp/support/
Dopenocd.cfg9 # Configure JTAG cable
/Zephyr-latest/include/zephyr/drivers/usb_c/
Dusbc_tc.h8 * @brief USB Type-C Cable and Connector API used for USB-C drivers
11 * Cable and Connector Specification Release 2.1
366 * @brief Cable plug. See 6.2.1.1.7 Cable Plug. Only applies to SOP' and SOP".
372 /* Message originated from a Cable Plug or VPD */
/Zephyr-latest/samples/drivers/video/capture/
DREADME.rst34 J35 camera connector. A USB cable should be connected from a host to the micro
38 J2 camera connector. A USB cable should be connected from a host to the micro
/Zephyr-latest/boards/snps/iotdk/doc/
Dindex.rst34 * A micro USB cable provides power to the board; however, if the
53 * Connect the digilent usb cable from your host to the board.
169 it using openocd and gdb. The program can be download via the USB cable into
/Zephyr-latest/samples/boards/96boards/argonkey/microphone/
DREADME.rst19 cable to get the output audio stream. The board can be powered
45 A USB to TTL 1V8 serial cable may be attached to the low speed connector on
/Zephyr-latest/samples/net/telnet/
DREADME.rst76 Connect ethernet cable from :zephyr:board:`Freedom-K64F <frdm_k64f>` board to a
97 Plug the Ethernet cable to the :zephyr:board:`Freedom-K64F <frdm_k64f>` board.
/Zephyr-latest/boards/ite/it8xxx2_evb/doc/
Dindex.rst93 #. Connect the Download Board to your host computer using the USB cable.
120 For USB to UART cable, connect the it8xxx2_evb as below:
124 | cable | J5 Connector |
/Zephyr-latest/boards/ite/it82xx2_evb/doc/
Dindex.rst110 #. Connect the Download Board to your host computer using the USB cable.
137 For USB to UART cable, connect the evolution motherboard as below:
141 | cable | motherboard |
/Zephyr-latest/samples/net/ipv4_autoconf/
DREADME.rst27 Connect ethernet cable from a :zephyr:board:`Freedom-K64F board <frdm_k64f>` to a Linux
/Zephyr-latest/boards/intel/common/
Defi_boot.rst40 #. Connect the board to the host system using the serial cable and
/Zephyr-latest/samples/boards/ti/cc13x2_cc26x2/system_off/
DREADME.rst38 1. Unplug the USB cable from the LaunchPad and reconnect it to fully
/Zephyr-latest/doc/hardware/peripherals/
Dtcpc.rst54 https://www.usb.org/document-library/usb-type-cr-cable-and-connector-specification-revision-21
/Zephyr-latest/boards/st/steval_stwinbx1/doc/
Dindex.rst11 a plastic case, an adapter board for DIL 24 sensors and a flexible cable.
265 No additional hardware is required except a USB-C cable. This method is fully
302 1. USB-C cable not connected
304 While pressing the USER button, connect the USB-C cable to the USB OTG STEVAL-STWINBX1
307 2. USB-C cable connected

1234567