Lines Matching full:with
14 * If no LICENSE file comes with this software, it is provided AS-IS.
110 …_0) /* Trigger edge set to rising edge (default setting for compatibility with some ADC on other S…
113 /* trigger edge selection duplicated with shifts [0; 4; 8; 12] */
121 /* trigger edge selection duplicated with shifts [0; 4; 8; 12] */
138 …_0) /* Trigger edge set to rising edge (default setting for compatibility with some ADC on other S…
141 /* trigger edge selection duplicated with shifts [0; 4; 8; 12] */
149 /* trigger edge selection duplicated with shifts [0; 4; 8; 12] */
259 … ( 3300UL) /* Analog voltage reference (Vref+) value with which temperature s…
265 … ( 3300UL) /* Analog voltage reference (Vref+) voltage with which temperature s…
278 * @brief Driver macro reserved for internal use: isolate bits with the
328 …de configuration to operate in independent mode or multimode (for devices with several ADC instanc…
359 * (setting possible with ADC enabled without conversion on going,
360 * ADC enabled with conversion on going, ...)
361 * Each feature can be updated afterwards with a unitary function
362 * and potentially with ADC in a different state than disabled,
390 * (functions with prefix "REG").
397 * (setting possible with ADC enabled without conversion on going,
398 * ADC enabled with conversion on going, ...)
399 * Each feature can be updated afterwards with a unitary function
400 * and potentially with ADC in a different state than disabled,
444 * (functions with prefix "INJ").
451 * (setting possible with ADC enabled without conversion on going,
452 * ADC enabled with conversion on going, ...)
453 * Each feature can be updated afterwards with a unitary function
454 * and potentially with ADC in a different state than disabled,
499 * @brief Flags defines which can be used with LL_ADC_ReadReg function
527 * @brief IT defines which can be used with LL_ADC_ReadReg and LL_ADC_WriteReg functions
538 /** @defgroup ADC_LL_EC_REGISTERS ADC registers compliant with specific purpose
541 /* List of ADC registers intended to be used (most commonly) with */
544 …egular conversion data register (corresponding to register DR) to be used with ADC configured in i…
546 … (corresponding to register CDR) to be used with ADC configured in multimode (available on STM32 d…
555 … /*!< ADC synchronous clock derived from AHB clock with prescaler division …
556 …CPRE_0) /*!< ADC synchronous clock derived from AHB clock with prescaler division …
557 … ) /*!< ADC synchronous clock derived from AHB clock with prescaler division …
558 …CPRE_0) /*!< ADC synchronous clock derived from AHB clock with prescaler division …
699 …mber of ADC conversions) is reached. This ADC mode is intended to be used with DMA mode non-circul…
700 …sferred (number of ADC conversions). This ADC mode is intended to be used with DMA mode circular. …
718 … ADC_SQR1_L_0) /*!< ADC group regular sequencer enable with 2 ranks in the sequ…
719 … ADC_SQR1_L_1 ) /*!< ADC group regular sequencer enable with 3 ranks in the sequ…
720 … ADC_SQR1_L_1 | ADC_SQR1_L_0) /*!< ADC group regular sequencer enable with 4 ranks in the sequ…
721 …_2 ) /*!< ADC group regular sequencer enable with 5 ranks in the sequ…
722 …_2 | ADC_SQR1_L_0) /*!< ADC group regular sequencer enable with 6 ranks in the sequ…
723 …_2 | ADC_SQR1_L_1 ) /*!< ADC group regular sequencer enable with 7 ranks in the sequ…
724 …_2 | ADC_SQR1_L_1 | ADC_SQR1_L_0) /*!< ADC group regular sequencer enable with 8 ranks in the sequ…
725 … ) /*!< ADC group regular sequencer enable with 9 ranks in the sequ…
726 … | ADC_SQR1_L_0) /*!< ADC group regular sequencer enable with 10 ranks in the seq…
727 … | ADC_SQR1_L_1 ) /*!< ADC group regular sequencer enable with 11 ranks in the seq…
728 … | ADC_SQR1_L_1 | ADC_SQR1_L_0) /*!< ADC group regular sequencer enable with 12 ranks in the seq…
729 …_2 ) /*!< ADC group regular sequencer enable with 13 ranks in the seq…
730 …_2 | ADC_SQR1_L_0) /*!< ADC group regular sequencer enable with 14 ranks in the seq…
731 …_2 | ADC_SQR1_L_1 ) /*!< ADC group regular sequencer enable with 15 ranks in the seq…
732 …_2 | ADC_SQR1_L_1 | ADC_SQR1_L_0) /*!< ADC group regular sequencer enable with 16 ranks in the seq…
741 …DC_CR1_DISCEN) /*!< ADC group regular sequencer discontinuous mode enable with sequence interrupti…
742 …C_CR1_DISCEN) /*!< ADC group regular sequencer discontinuous mode enabled with sequence interrupti…
743 …DC_CR1_DISCEN) /*!< ADC group regular sequencer discontinuous mode enable with sequence interrupti…
744 …DC_CR1_DISCEN) /*!< ADC group regular sequencer discontinuous mode enable with sequence interrupti…
745 …DC_CR1_DISCEN) /*!< ADC group regular sequencer discontinuous mode enable with sequence interrupti…
746 …DC_CR1_DISCEN) /*!< ADC group regular sequencer discontinuous mode enable with sequence interrupti…
747 …DC_CR1_DISCEN) /*!< ADC group regular sequencer discontinuous mode enable with sequence interrupti…
748 …DC_CR1_DISCEN) /*!< ADC group regular sequencer discontinuous mode enable with sequence interrupti…
814 …njected conversion trigger from ADC group regular. Setting compliant only with group injected trig…
824 … ( ADC_JSQR_JL_0) /*!< ADC group injected sequencer enable with 2 ranks in the sequ…
825 … (ADC_JSQR_JL_1 ) /*!< ADC group injected sequencer enable with 3 ranks in the sequ…
826 … (ADC_JSQR_JL_1 | ADC_JSQR_JL_0) /*!< ADC group injected sequencer enable with 4 ranks in the sequ…
835 …JDISCEN) /*!< ADC group injected sequencer discontinuous mode enable with sequence interrupti…
975 … /*!< ADC dual mode enabled: group injected alternate trigger. Works only with external triggers (…
985 …*!< ADC triple mode enabled: group injected alternate trigger. Works only with external triggers (…
994 …ar conversions are transferred by DMA: each ADC uses its own DMA channel, with its individual DMA …
995 …mber of ADC conversions) is reached. This ADC mode is intended to be used with DMA mode non-circul…
996 …mber of ADC conversions) is reached. This ADC mode is intended to be used with DMA mode non-circul…
997 …mber of ADC conversions) is reached. This ADC mode is intended to be used with DMA mode non-circul…
998 …mber of ADC conversions) is reached. This ADC mode is intended to be used with DMA mode non-circul…
999 …mber of ADC conversions) is reached. This ADC mode is intended to be used with DMA mode non-circul…
1000 …mber of ADC conversions) is reached. This ADC mode is intended to be used with DMA mode non-circul…
1123 * number is returned, either defined with number
1124 * or with bitfield (only one bit must be set).
1190 * comparison with internal channel parameter to be done
1221 * number in ADC registers. The differentiation is made only with
1329 * number in ADC registers. The differentiation is made only with
1350 * define a single channel to monitor with analog watchdog
1352 * @note To be used with function @ref LL_ADC_SetAnalogWDMonitChannels().
1384 * comparison with internal channel parameter to be done
1479 * @note To be used with function @ref LL_ADC_SetAnalogWDThresholds().
1480 * Example, with a ADC resolution of 8 bits, to set the value of
1501 * @note To be used with function @ref LL_ADC_GetAnalogWDThresholds().
1502 * Example, with a ADC resolution of 8 bits, to get the value of
1522 * or ADC slave from raw value with both ADC conversion data concatenated.
1525 * In this case the transferred data need to processed with this macro
1542 * - Multimode (for devices with several ADC instances)
1561 * @note This check is required by functions with setting conditioned to
1565 * @note On devices with only 1 ADC common instance, parameter of this macro
1567 * with devices featuring several ADC common instances).
1660 * On devices with small package, the pin Vref+ is not present
1697 * with TS_ADC_DATA = temperature sensor raw data measured by ADC
1756 * with TS_ADC_DATA = temperature sensor raw data measured by ADC
1763 * of the current device has characteristics in line with
1834 * intended to be used (most commonly) with DMA transfer.
1838 * @note This macro is intended to be used with LL DMA driver, refer to
1846 * @note For devices with several ADC: in multimode, some devices
1858 * (1) Available on devices with several ADC instances.
2202 /* to match with triggers literals definition. */ in LL_ADC_REG_GetTriggerSource()
2246 * - For devices with sequencer fully configurable
2256 * - For devices with sequencer not fully configurable
2307 * - For devices with sequencer fully configurable
2317 * - For devices with sequencer not fully configurable
2495 /* Set bits with content of parameter "Channel" with bits position */ in LL_ADC_REG_SetSequencerRanks()
2497 /* Parameters "Rank" and "Channel" are used with masks because containing */ in LL_ADC_REG_SetSequencerRanks()
2519 * with parts of literals LL_ADC_CHANNEL_x or using
2524 * process the returned value with the helper macro
2587 * comparison with internal channel parameter to be done
2645 * This ADC mode is intended to be used with DMA mode non-circular.
2649 * This ADC mode is intended to be used with DMA mode circular.
2655 * @note For devices with several ADC instances: ADC multimode DMA
2681 * This ADC mode is intended to be used with DMA mode non-circular.
2685 * This ADC mode is intended to be used with DMA mode circular.
2691 * @note For devices with several ADC instances: ADC multimode DMA
2712 * @note This feature is aimed to be set when using ADC with
2837 /* to match with triggers literals definition. */ in LL_ADC_INJ_GetTriggerSource()
3012 /* Set bits with content of parameter "Channel" with bits position */ in LL_ADC_INJ_SetSequencerRanks()
3014 /* Parameters "Rank" and "Channel" are used with masks because containing */ in LL_ADC_INJ_SetSequencerRanks()
3032 * with parts of literals LL_ADC_CHANNEL_x or using
3037 * process the returned value with the helper macro
3076 * comparison with internal channel parameter to be done
3093 * updated after one ADC conversion trigger and with data
3101 * ADC group injected automatic trigger is compliant only with
3281 /* Set bits with content of parameter "SamplingTime" with bits position */ in LL_ADC_SetChannelSamplingTime()
3283 /* Parameter "Channel" is used with masks because containing */ in LL_ADC_SetChannelSamplingTime()
3381 * with analog watchdog from sequencer channel definition,
3483 * with parts of literals LL_ADC_CHANNEL_x or using
3488 * process the returned value with the helper macro
3634 * or multimode (for devices with several ADC instances).
3665 * or multimode (for devices with several ADC instances).
3697 * each ADC uses its own DMA channel, with its individual
3705 * This ADC mode is intended to be used with DMA mode non-circular.
3709 * This ADC mode is intended to be used with DMA mode circular.
3719 * is a raw data with ADC master and slave concatenated.
3746 * each ADC uses its own DMA channel, with its individual
3754 * This ADC mode is intended to be used with DMA mode non-circular.
3758 * This ADC mode is intended to be used with DMA mode circular.
3768 * is a raw data with ADC master and slave concatenated.
3969 * with feature oversampling).
3982 * @note For devices with feature oversampling: Oversampling
3997 * @note For devices with feature oversampling: Oversampling
4012 * @note For devices with feature oversampling: Oversampling
4027 * @note For devices with feature oversampling: Oversampling
4042 * or raw data with ADC master and slave concatenated.
4043 * @note If raw data with ADC master and slave concatenated is retrieved,
4142 * with feature oversampling).
4167 * @note For devices with feature oversampling: Oversampling
4194 * @note For devices with feature oversampling: Oversampling
4221 * @note For devices with feature oversampling: Oversampling
4248 * @note For devices with feature oversampling: Oversampling