Lines Matching +full:100 +full:base +full:- +full:t
4 * SPDX-License-Identifier: Apache-2.0
10 flexram,num-ram-banks = <4>;
12 flexram,bank-spec = <FLEXRAM_OCRAM>,
19 clock-frequency = <500000000>;
35 /delete-node/ arm-podf;
37 ipg-podf {
38 clock-div = <4>;
61 irq-shared-offset = <0>;
62 dma-channels = <16>;
67 /* Remove GPIO3-GPIO9, they don't exist on RT1010 */
68 /delete-node/ gpio@401c0000;
69 /delete-node/ gpio@401c4000;
70 /delete-node/ gpio@42000000;
71 /delete-node/ gpio@42004000;
72 /delete-node/ gpio@42008000;
73 /delete-node/ gpio@4200c000;
76 /delete-node/ gpio@401bc000;
79 compatible = "nxp,imx-gpio";
82 gpio-controller;
83 #gpio-cells = <2>;
100 /* Remove Quad TImers, they don't exist on RT1010 */
101 /delete-node/ qtmr@401dc000;
102 /delete-node/ qtmr@401e0000;
103 /delete-node/ qtmr@401e4000;
104 /delete-node/ qtmr@401e8000;
107 /delete-node/ spi@402a8000;
109 compatible = "nxp,imx-flexspi";
112 #address-cells = <1>;
113 #size-cells = <0>;
114 ahb-bufferable;
115 ahb-cacheable;
120 /* Remove SEMC, it doesn't exist on RT1010 */
121 /delete-node/ semc0@402f0000;
123 /* Fixup LPI2C1 and LPI2C2, they have different base addr on RT1010 */
124 /delete-node/ i2c@403f0000;
125 /delete-node/ i2c@403f4000;
129 clock-frequency = <I2C_BITRATE_STANDARD>;
130 #address-cells = <1>;
131 #size-cells = <0>;
140 clock-frequency = <I2C_BITRATE_STANDARD>;
141 #address-cells = <1>;
142 #size-cells = <0>;
149 /* Remove LPI2C3 & LPI2C4, they don't exist on RT1010 */
150 /delete-node/ i2c@403f8000;
151 /delete-node/ i2c@403fc000;
153 /* Remove LCDIF, it doesn't exist on RT1010 */
154 /delete-node/ display-controller@402b8000;
156 /* Fixup LPSPI1 and LPSPI2, they have different base addr on RT1010 */
157 /delete-node/ spi@40394000;
158 /delete-node/ spi@40398000;
165 #address-cells = <1>;
166 #size-cells = <0>;
175 #address-cells = <1>;
176 #size-cells = <0>;
179 /* Remove LPUART5-8, they don't exist on RT1010 */
180 /delete-node/ uart@40194000;
181 /delete-node/ uart@40198000;
182 /delete-node/ uart@4019c000;
183 /delete-node/ uart@401a0000;
185 /* Remove ADC2, it doesn't exist on RT1010 */
186 /delete-node/ adc@400C8000;
189 /delete-node/ spi@402a4000;
191 /* Fixup FlexPWM1 it has different base addr and interrupt numbers on RT1010 */
192 /delete-node/ flexpwm@403dc000;
199 compatible = "nxp,imx-pwm";
202 #pwm-cells = <3>;
209 compatible = "nxp,imx-pwm";
212 #pwm-cells = <3>;
219 compatible = "nxp,imx-pwm";
222 #pwm-cells = <3>;
229 compatible = "nxp,imx-pwm";
232 #pwm-cells = <3>;
238 /* Remove FlexPWM2-4, they don't exist on RT1010 */
239 /delete-node/ flexpwm@403e0000;
240 /delete-node/ flexpwm@403e4000;
241 /delete-node/ flexpwm@403e8000;
243 /* Remove Ethernet, it doesn't exist on RT1010 */
244 /delete-node/ enet@402d8000;
246 /* Fixup USB it has different base addr and interrupt numbers on RT1010 */
247 /delete-node/ usbd@402e0000;
252 interrupt-names = "usb_otg";
254 num-bidir-endpoints = <8>;
258 /* Remove USB2, it doesn't exist on RT1010 */
259 /delete-node/ usbd@402e0200;
261 /* Remove USDHC, they don't exist on RT1010 */
262 /delete-node/ usdhc@402c0000;
263 /delete-node/ usdhc@402c4000;
265 /* Remove CSI, it doesn't exist on RT1010 */
266 /delete-node/ csi@402bc000;
268 /* Remove FLEXCAN, they don't exist on RT1010 */
269 /delete-node/ can@401d0000;
270 /delete-node/ can@401d4000;
271 /delete-node/ can@401d8000;
273 /* Remove WDOG2, it doesn't exist on RT1010 */
274 /delete-node/ wdog@400d0000;
276 /* Fix SAI1, 3, it has different base addr on RT1010 */
277 /delete-node/ sai@40384000;
278 /delete-node/ sai@4038c000;
280 compatible = "nxp,mcux-i2s";
281 #address-cells = <1>;
282 #size-cells = <0>;
283 #pinmux-cells = <2>;
287 clock-mux = <2>;
290 * = (24MHz * (32 + 77 / 100)) / 1 = 786.48 MHz
292 pll-clocks = <&anatop 0x70 0xC000 0>,
296 <&anatop 0x90 0x3FFFFFFF 100>;
297 pll-clock-names = "src", "lp", "pd", "num", "den";
299 * Based on this requirement, pre-div must be at least 3
300 * The pre-div and post-div are one less than the actual divide-by amount.
301 * A pre-div value of 0x1 results in a pre-divider of
304 pre-div = <0x3>;
309 dma-names = "rx", "tx";
313 nxp,tx-channel = <1>;
314 nxp,tx-dma-channel = <0>;
315 nxp,rx-dma-channel = <1>;
320 compatible = "nxp,mcux-i2s";
321 #address-cells = <1>;
322 #size-cells = <0>;
323 #pinmux-cells = <2>;
327 clock-mux = <2>;
328 pre-div = <0>;
330 pll-clocks = <&anatop 0x70 0xC000 0>,
334 <&anatop 0x90 0x3FFFFFFF 100>;
335 pll-clock-names = "src", "lp", "pd", "num", "den";
339 dma-names = "rx", "tx";
340 nxp,tx-channel = <0>;
341 nxp,tx-dma-channel = <5>;
342 nxp,rx-dma-channel = <6>;
346 /* Remove SAI2, it doesn't exist on RT1010 */
347 /delete-node/ sai@40388000;
352 /delete-node/ &lpspi3;
353 /delete-node/ &lpspi4;