Lines Matching +full:ahb +full:- +full:prefetch
4 * SPDX-License-Identifier: Apache-2.0
7 #include "frdm_mcxn947-pinctrl.dtsi"
8 #include <zephyr/dt-bindings/i2c/i2c.h>
9 #include <zephyr/dt-bindings/input/input-event-codes.h>
19 mcuboot-button0 = &user_button_2;
23 compatible = "gpio-leds";
42 compatible = "gpio-keys";
58 * This node describes the GPIO pins of the LCD-PAR-S035 panel 8080 interface.
60 nxp_lcd_8080_connector: lcd-8080-connector {
61 compatible = "nxp,lcd-8080";
62 #gpio-cells = <2>;
63 gpio-map-mask = <0xffffffff 0xffffffc0>;
64 gpio-map-pass-thru = <0 0x3f>;
65 gpio-map = <9 0 &gpio4 6 0>, /* Pin 9, LCD touch INT */
72 pinctrl-0 = <&pinmux_flexcomm1_lpspi>;
73 pinctrl-names = "default";
77 pinctrl-0 = <&pinmux_flexcomm2_lpi2c>;
78 pinctrl-names = "default";
79 clock-frequency = <I2C_BITRATE_STANDARD>;
83 current-speed = <115200>;
84 pinctrl-0 = <&pinmux_flexcomm2_lpuart>;
85 pinctrl-names = "default";
89 current-speed = <115200>;
90 pinctrl-0 = <&pinmux_flexcomm4_lpuart>;
91 pinctrl-names = "default";
95 pinctrl-0 = <&pinmux_flexcomm7_lpi2c>;
96 pinctrl-names = "default";
97 clock-frequency = <I2C_BITRATE_STANDARD>;
100 reset-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
101 pwdn-gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>;
109 program-mem = <0x4000000>;
110 video_sdma: video-sdma {
112 compatible = "nxp,video-smartdma";
113 pinctrl-0 = <&pinmux_smartdma_camera>;
114 pinctrl-names = "default";
116 vsync-pin = <4>;
117 hsync-pin = <11>;
118 pclk-pin = <5>;
137 compatible = "mmio-sram";
141 compatible = "mmio-sram";
148 compatible = "fixed-partitions";
149 #address-cells = <1>;
150 #size-cells = <1>;
164 label = "image-0";
168 label = "image-1";
176 pinctrl-0 = <&pinmux_flexspi>;
177 pinctrl-names = "default";
178 ahb-prefetch;
179 ahb-bufferable;
180 ahb-cacheable;
181 ahb-read-addr-opt;
182 combination-mode;
183 rx-clock-source = <1>;
187 compatible = "nxp,imx-flexspi-nor";
191 spi-max-frequency = <133000000>;
192 jedec-id = [ef 40 17];
193 erase-block-size = <4096>;
194 write-block-size = <1>;
195 cs-interval-unit = <1>;
196 cs-interval = <2>;
197 cs-hold-time = <3>;
198 cs-setup-time = <3>;
199 data-valid-time = <2>;
200 column-space = <0>;
205 pinctrl-0 = <&pinmux_dac0>;
206 pinctrl-names = "default";
210 pinctrl-0 = <&pinmux_sai1>;
211 pinctrl-names = "default";
215 pinctrl-0 = <&pinmux_sai0>;
216 pinctrl-names = "default";
220 pinctrl-0 = <&pinmux_enet_qos>;
221 pinctrl-names = "default";
225 phy-connection-type = "rmii";
226 zephyr,random-mac-address;
227 phy-handle = <&phy>;
231 phy: ethernet-phy@0 {
232 compatible = "ethernet-phy";
239 pinctrl-0 = <&pinmux_flexpwm1_pwm0>;
240 pinctrl-names = "default";
244 pinctrl-0 = <&pinmux_usdhc0>;
245 pinctrl-1 = <&pinmux_usdhc0>;
246 pinctrl-2 = <&pinmux_usdhc0>;
247 cd-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
248 pinctrl-names = "default", "slow", "med";
249 no-1-8-v;
253 pinctrl-0 = <&pinmux_lpadc0>;
254 pinctrl-names = "default";
260 dma-names = "tx";
261 shifters-count = <8>;
262 timers-count = <1>;
263 enwr-pin = <1>;
264 rd-pin = <0>;
265 data-pin-start = <16>;
266 reset-gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>;
267 cs-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
268 rs-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
269 pinctrl-0 = <&pinmux_flexio_lcd>;
270 pinctrl-names = "default";
274 pinctrl-0 = <&pinmux_lpcmp0>;
275 pinctrl-names = "default";
279 pinctrl-0 = <&pinmux_i3c1>;
280 pinctrl-names = "default";
284 pinctrl-0 = <&pinmux_flexcan0>;
285 pinctrl-names = "default";
289 pinctrl-0 = <&pinmux_sctimer>;
290 pinctrl-names = "default";