Lines Matching +full:cs +full:- +full:setup +full:- +full:time
10 MEC150x except for an enhanced Boot-ROM SPI loader. The SPI image format has
18 - MEC1521HA0SZ ARM Cortex-M4 Processor
19 - 256 KB RAM and 64 KB boot ROM
20 - Keyboard interface
21 - ADC & GPIO headers
22 - UART0, UART1, and UART2
23 - FAN0, FAN1, FAN2 headers
24 - FAN PWM interface
25 - JTAG/SWD, ETM and MCHP Trace ports
26 - PECI interface 3.0
27 - I2C voltage translator
28 - 10 SMBUS headers
29 - 4 SGPIO headers
30 - VCI interface
31 - 5 independent Hardware Driven PS/2 Ports
32 - eSPI header
33 - 3 Breathing/Blinking LEDs
34 - 2 Sockets for SPI NOR chips
35 - One reset and VCC_PWRDGD pushbuttons
36 - One external PCA9555 I/O port with jumper selectable I2C address.
37 - One external LTC2489 delta-sigma ADC with jumper selectable I2C address.
38 - Board power jumper selectable from +5V 2.1mm/5.5mm barrel connector or USB Micro A connector.
48 +-----------+------------+-------------------------------------+
51 | NVIC | on-chip | nested vector interrupt controller |
52 +-----------+------------+-------------------------------------+
53 | SYSTICK | on-chip | systick |
54 +-----------+------------+-------------------------------------+
55 | UART | on-chip | serial port |
56 +-----------+------------+-------------------------------------+
57 | GPIO | on-chip | gpio |
58 +-----------+------------+-------------------------------------+
59 | I2C | on-chip | i2c |
60 +-----------+------------+-------------------------------------+
61 | PINMUX | on-chip | pinmux |
62 +-----------+------------+-------------------------------------+
63 | PS/2 | on-chip | ps2 |
64 +-----------+------------+-------------------------------------+
65 | KSCAN | on-chip | kscan |
66 +-----------+------------+-------------------------------------+
67 | TACH | on-chip | tachometer |
68 +-----------+------------+-------------------------------------+
83 - MEC15xx EVB ASSY 6853 Rev A `MEC15xx EVB Schematic`_
84 - MEC1501 144WFBA SOLDER DC ASSY 6883 with MEC152x silicon `MEC1501 Daughter Card Schematic`_
85 - SPI DONGLE ASSY 6791 `SPI Dongle Schematic`_
91 on-chip PLL to generate a resulting EC clock rate of 12 MHz. See Processor clock
109 Power-related jumpers
110 ---------------------
113 (5.5mm OD, 2.1mm ID) and move the jumper to ``JP88 5-6``.
115 If you wish to power from micro-USB type A/B connector ``P12``, move the
116 jumper to ``JP88 7-8``.
121 +-------+------+------+------+------+------+------+------+------+------+------+
124 | 1-2 | 1-2 | 1-2 | 1-2 | 1-2 | 1-2 | 1-2 | 1-2 | 1-2 | 1-2 | 1-2 |
125 +-------+------+------+------+------+------+------+------+------+------+------+
127 +------+------+------+------+------+------+------+------+------+------+
130 | 1-2 | 1-2 | 1-2 | 1-2 | 1-2 | 1-2 | 1-2 | 1-2 | 1-2 | 1-2 |
131 +------+------+------+------+------+------+------+------+------+------+
133 +------+------+-------+-------+-------+
136 | 1-2 | 1-2 | 1-2 | 1-2 | 2-3 |
137 +------+------+-------+-------+-------+
141 +------------------+-----------+--------------+
145 | 1-2 | 1-2 | 2-3 |
146 +------------------+-----------+--------------+
148 Boot-ROM Straps.
149 ----------------
151 These jumpers configure MEC1501 Boot-ROM straps.
153 +-------------+------------+--------------+-------------+
157 | 2-3 | 1-2 | 2-3 | 1-2 |
158 +-------------+------------+--------------+-------------+
160 ``JP96 1-2`` pulls SHD SPI CS0# up to VTR2. MEC1501 Boot-ROM samples
164 --------------------------
167 PVT SPI, SHD SPI and LED0-2 respectively.
169 +----------+----------+--------+-----------+----------+---------+
171 | (UART2) | (UART2) | (SWD) | (PVT SPI) | (SHD SPI)| (LED0-2)|
173 | 1-2 | | 2-3 | 2-3 | 2-3 | 1-2 |
174 +----------+----------+--------+-----------+----------+---------+
175 | 4-5 | 4-5 | | 5-6 | 5-6 | 3-4 |
176 +----------+----------+--------+-----------+----------+---------+
177 | 7-8 | | 8-9 | 8-9 | 8-9 | 5-6 |
178 +----------+----------+--------+-----------+----------+---------+
179 | 10-11 | 10-11 | | 11-12 | 11-12 | |
180 +----------+----------+--------+-----------+----------+---------+
181 | | | | 14-15 | 14-15 | |
182 +----------+----------+--------+-----------+----------+---------+
183 | | | | 17-18 | 20-21 | |
184 +----------+----------+--------+-----------+----------+---------+
186 .. note:: For UART2 make sure JP39 have jumpers connected 1-2, 3-4.
209 ------------------------------------
210 +-------+-------+
213 | 1-2 | 2-3 |
214 +-------+-------+
217 -------------------------------------------
218 +-------+-------+
221 | NC | 1-2 |
222 +-------+-------+
236 Setup section in Programming and Debugging
238 #. If you use Dediprog SF100 programmer, then setup it.
243 Follow the `SF100 Linux manual`_ to complete setup of the SF100 programmer.
244 For Linux please make sure that you copied ``60-dediprog.rules``
248 .. code-block:: console
250 $ udevadm control --reload
256 that directory. For the pre-production MEC150x use `MEC150x SPI Image Gen`_
263 .. code-block:: console
268 For the pre-production MEC1501 SOC use everglades_spi_gen_lin64.
273 .. code-block:: console
289 .. list-table:: Microchip board wiring
292 * -
297 -
313 +------------+---------------+
318 +------------+---------------+
320 +------------+---------------+
321 | CS | 3 |
322 +------------+---------------+
324 +------------+---------------+
326 +------------+---------------+
328 +------------+---------------+
333 #. Apply power to the board via a micro-USB cable.
334 Configure this option by using a jumper between ``JP88 7-8``.
348 #. Build :zephyr:code-sample:`hello_world` application as you would normally do.
361 .. code-block:: console
363 $ minicom -D /dev/ttyUSB0 -o
365 The -o option tells minicom not to send the modem initialization
368 - Speed: 115200
369 - Data: 8 bits
370 - Parity: None
371 - Stop bits: 1
376 .. code-block:: console
388 .. note:: If you don't want to press Reset button every time, you can disconnect
406 are lit. If one of these is off, then check the power-related jumpers again.
422 * JP99 1-2 Connected Connect I2C01_SDA from CPU to header J5
423 * JP99 13-14 Connected Connect I2C01_SCL from CPU to header J5
424 * JP25 21-22 Connected External pull-up for I2C01_SDA
425 * JP25 23-24 Connected External pull-up for I2C01_SCL
433 .. target-notes::
444 …hipTech/CPGZephyrDocs/blob/master/MEC1501/Everglades%20EVB%20-%20Assy_6853%20Rev%20A1p1%20-%20SCH.…
446 …ter/MEC1501/MEC1501%20Socket%20DC%20for%20EVERGLADES%20EVB%20-%20Assy_6883%20Rev%20A0p1%20-%20SCH.…
448 …ter/MEC1501/MEC1503%20Socket%20DC%20for%20EVERGLADES%20EVB%20-%20Assy_6856%20Rev%20A1p0%20-%20SCH.…
450 …master/MEC1501/SPI%20Dongles%20and%20Aardvark%20Interposer%20Assy%206791%20Rev%20A1p1%20-%20SCH.pdf