Lines Matching +full:clock +full:- +full:lane

6 The i.MX7S SoC is a Hybrid multi-core processor composed of Single Cortex A7
19 - 6-axis Accelerometer Magnetometer: NXP FXOS8700CQ (I2C4 interface)
20 - 3-axis Gyroscope: NXP FXAS21002C (I2C4 interface)
21 - Altimeter: NXP MPL3115A2 (I2C4 interface)
22 - NXP NTAG NT3H1101 (I2C2 interface)
23 - Audio Codec: NXP SGTL5000 (I2C4 and SAI1 interfaces)
24 - S1 - Reset Button (POR_B signal)
25 - S2 - User Defined button (ENET1_RD1/GPIO7_IO1 signal)
26 - S3 - On/Off (MX7_ONOFF signal)
27 - Board to board connector (34 configurable pins)
28 - mikroBUS expansion connector
29 - 10-pin needle JTAG Connector
30 - Debug USB exposing two UARTs (UART1 for A7 and UART2 for M4)
31 - MIPI DSI 1 lane Connector
32 - LCD Touch Connector (I2C2 interface)
33 - Audio Jack: Mic and Stereo Headphone
38 - CPU i.MX7 Solo with a Single Cortex A7 (800MHz) core and
40 - Memory
42   - RAM -> A7: 4GB (Kingston 08EMCP04)
43   - RAM -> M4: 3x32KB (TCML, TCMU, OCRAM_S), 1x128KB (OCRAM) and 1x256MB (DDR)
44   - Flash -> A7: 8GB eMMC (Kingston 08EMCP04)
45 - Multimedia
47   - MIPI CSI 1 lane connector with 5MP OV5640 camera module (I2C2 interface)
48 - Connectivity
50   - Board to board connector (34 configurable pins)
51   - Micro USB 2.0 OTG connector (USB_OTG1 interface)
52   - Murata Type 1DX Wi-Fi IEEE 802.11b/g/n and Bluetooth 4.1 plus EDR
54 - Li-ion/Li-polymer Battery Charger: NXP BC3770 (I2C1 interface)
55 - Power management integrated circuit (PMIC): NXP PF3000 (I2C1 interface)
60 - `i.MX 7 Series Website`_
61 - `i.MX 7 Solo Datasheet`_
62 - `i.MX 7 Solo Reference Manual`_
63 - `WaRP7 Site`_
64 - `WaRP7 Quick Start Guide`_
65 - `WaRP7 User Guide`_
66 - `WaRP7 GitHub repository`_
74 +-----------+------------+-------------------------------------+
77 | NVIC      | on-chip    | nested vector interrupt controller  |
78 +-----------+------------+-------------------------------------+
79 | SYSTICK   | on-chip    | systick                             |
80 +-----------+------------+-------------------------------------+
81 | GPIO      | on-chip    | gpio                                |
82 +-----------+------------+-------------------------------------+
83 | I2C       | on-chip    | i2c                                 |
84 +-----------+------------+-------------------------------------+
85 | UART      | on-chip    | serial port-polling;                |
86 |           |            | serial port-interrupt               |
87 +-----------+------------+-------------------------------------+
88 | SENSOR    | off-chip   | fxos8700 polling;                   |
92 +-----------+------------+-------------------------------------+
105 +---------------+---------------------+--------------------------------+
109 +---------------+---------------------+--------------------------------+
111 +---------------+---------------------+--------------------------------+
113 +---------------+---------------------+--------------------------------+
115 +---------------+---------------------+--------------------------------+
117 +---------------+---------------------+--------------------------------+
119 +---------------+---------------------+--------------------------------+
121 +---------------+---------------------+--------------------------------+
123 +---------------+---------------------+--------------------------------+
125 System Clock
128 The M4 Core is configured to run at a 200 MHz clock speed.
149 +------------+-----------------------+------------------------+-----------------------+------------…
150 | Region     | Cortex-A7             | Cortex-M4 (System Bus) | Cortex-M4 (Code Bus)  | Size       …
152 | DDR        | 0x80000000-0xFFFFFFFF | 0x80000000-0xDFFFFFFF  | 0x10000000-0x1FFEFFFF | 2048MB (les…
153 +------------+-----------------------+------------------------+-----------------------+------------…
154 | OCRAM      | 0x00900000-0x0091FFFF | 0x20200000-0x2021FFFF  | 0x00900000-0x0091FFFF | 128KB      …
155 +------------+-----------------------+------------------------+-----------------------+------------…
156 | TCMU       | 0x00800000-0x00807FFF | 0x20000000-0x20007FFF  |                       | 32KB       …
157 +------------+-----------------------+------------------------+-----------------------+------------…
158 | TCML       | 0x007F8000-0x007FFFFF |                        | 0x1FFF8000-0x1FFFFFFF | 32KB       …
159 +------------+-----------------------+------------------------+-----------------------+------------…
160 | OCRAM_S    | 0x00180000-0x00187FFF | 0x20180000-0x20187FFF  | 0x00000000-0x00007FFF | 32KB       …
161 +------------+-----------------------+------------------------+-----------------------+------------…
162 | QSPI Flash |                       |                        | 0x08000000-0x0BFFFFFF | 64MB       …
163 +------------+-----------------------+------------------------+-----------------------+------------…
169 - `i.MX 7 Solo Reference Manual`_ from page 182 (section 2.1.2 and 2.1.3)
170 - `Toradex Wiki`_
178 .. code-block:: none
181    - &ddr_code
182    - &tcml_code
183    - &ocram_code
184    - &ocram_s_code
185    - &ocram_pxp_code
186    - &ocram_epdc_code
189    - &ddr_sys
190    - &tcmu_sys
191    - &ocram_sys
192    - &ocram_s_sys
193    - &ocram_pxp_sys
194    - &ocram_epdc_sys
198 u-boot.
206 After powering up the platform stop the u-boot execution on the A7 core and
207 expose the eMMC as mass storage with the following command in the u-boot
210 u-boot prompt.
211 Set the u-boot environment variables and run the zephyr.bin from the
214 .. code-block:: console
242 Download and install `J-Link Tools`_ and `NXP iMX7D Connect CortexM4.JLinkScript`_.
244 To run Zephyr Binary using J-Link, create the following script to get the
247 get-pc-sp.sh:
248 .. code-block:: console
254    pc=$(od -An -N 8 -t x4 $firmware | awk '{print $2;}')
255    sp=$(od -An -N 8 -t x4 $firmware | awk '{print $1;}')
261 Get the SP and PC from firmware binary: ``./get-pc-sp.sh zephyr.bin``
262 .. code-block:: console
267 Plug in the J-Link into the board and PC and run the J-Link command line tool:
269 .. code-block:: console
271    /usr/bin/JLinkExe -device Cortex-M4 -if JTAG \
272       -speed 4000 -autoconnect 1 -jtagconf -1,-1 \
273       -jlinkscriptfile iMX7D_Connect_CortexM4.JLinkScript
283 Issue the following commands inside J-Link commander:
285 .. code-block:: console
300 - `Loading Code on Cortex-M4 from Linux for the i.MX 6SoloX and i.MX 7Dual/7Solo Application Proces…
301 - `J-Link iMX7D Instructions`_
307    https://github.com/WaRP7/WaRP7-User-Guide/releases/download/v1.3/User_Guide_Manual_v1-3.pdf
310    https://www.nxp.com/docs/en/supporting-information/WARP7-LEAFLET-QSG.pdf
316 …nxp.com/products/processors-and-microcontrollers/applications-processors/i.mx-applications-process…
319    https://www.nxp.com/docs/en/data-sheet/IMX7SCEC.pdf
324 .. _J-Link Tools:
325    https://www.segger.com/downloads/jlink/#J-LinkSoftwareAndDocumentationPack
330 .. _Loading Code on Cortex-M4 from Linux for the i.MX 6SoloX and i.MX 7Dual/7Solo Application Proce…
331    https://www.nxp.com/docs/en/application-note/AN5317.pdf
333 .. _J-Link iMX7D Instructions:
337 …https://developer.toradex.com/knowledge-base/freertos-on-the-cortex-m4-of-a-colibri-imx7#Memory_ar…