Lines Matching +full:reset +full:- +full:causes +full:- +full:en
6 of the MAX32672 microcontroller, which is a small, high-reliability, ultra-low power,
7 32-bit microcontroller. The MAX32672 is a secure and cost-effective solution
8 for motion/motor control, industrial sensors, and battery-powered medical devices and offers legacy
9 designs an easy, cost-optimal upgrade path from 8-bit or 16-bit microcontrollers.
16 - MAX32672 MCU:
18 - High-Efficiency Microcontroller for Low-Power High-Reliability Devices
20 - Arm Cortex-M4 Processor with FPU up to 100MHz
21 - 1MB Dual-Bank Flash with Error Correction
22 - 200KB SRAM (160KB with ECC Enabled), Optionally Preserved in Lowest Power Modes
23 - EEPROM Emulation on Flash
24 - 16KB Unified Cache with ECC
25 - Resource Protection Unit (RPU) and MemoryProtection Unit (MPU)
26 - Dual- or Single-Supply Operation, 1.7V to 3.6V
27 - Wide Operating Temperature: -40°C to +105°C
29 - Flexible Clocking Schemes
31 - Internal High-Speed 100MHz Oscillator
32 - Internal Low-Power 7.3728MHz and Ultra-Low-Power 80kHz Oscillators
33 - 16MHz–32MHz Oscillator, 32.768kHz Oscillator(External Crystal Required)
34 - External Clock Input for CPU, LPUART, LPTMR
36 - Power Management Maximizes Uptime for Battery Applications
38 - 59.8μA/MHz ACTIVE at 0.9V up to 12MHz(CoreMark®)
39 - 56.6μA/MHz ACTIVE at 1.1V up to 100MHz(While(1))
40 - 3.09μA Full Memory Retention Power in BACKUPMode at VDD = 1.8V
41 - 350nA Ultra-Low-Power RTC at
42 - Wake from LPUART or LPTMR
44 - Optimal Peripheral Mix Provides Platform Scalability
46 - Up to 42 General-Purpose I/O Pins
47 - Up to Three SPI Master/Slave (up to 50Mbps)
48 - Up to Three 4-Wire UART
49 - Up to Three I2C Master/Slave 3.4Mbps High Speed
50 - Up to Four 32-Bit Timers (TMR)
51 - Up to Two Low-Power 32-Bit Timers (LPTMR)
52 - One I2S Master/Slave for Digital Audio Interface
53 - 12-Channel, 12-Bit, 1Msps SAR ADC with On-DieTemperature Sensor
55 - Security and Integrity
57 - Optional ECDSA-Based Cryptographic SecureBootloader in ROM
58 - Secure Cryptographic Accelerator for Elliptic Curve
59 - AES-128/192/256 Hardware Acceleration Engine
61 - Benefits and Features of MAX32672EVKIT:
63 - Selectable, On-Board, High-Precision Voltage Reference
64 - 128 x 128 (1.45in) Color TFT Display with SPI Interface
65 - Breadboard-Compatible Headers
66 - USB 2.0 Micro B-to-Serial UARTs
67 - UART0 and LPUART0 Interface Is Selectable through On-Board Jumpers
68 - All GPIOs Signals Accessed through 0.1in Headers
69 - 12 Analog Inputs Accessed through 0.1in Headers with Optional Filtering
70 - 10-Pin Arm® Cortex® SWD Connector
71 - Board Power Provided by USB Port
72 - On-Board, 3.3V LDO Regulator
73 - Test Loops Provided to Supply Optional VCORE Power Externally
74 - Individual Power Measurement on All IC Rails through Jumpers
75 - Two General-Purpose LEDs and One General-Purpose Pushbutton Switch
82 +-----------+------------+-------------------------------------+
85 | NVIC | on-chip | nested vector interrupt controller |
86 +-----------+------------+-------------------------------------+
87 | SYSTICK | on-chip | systick |
88 +-----------+------------+-------------------------------------+
89 | CLOCK | on-chip | clock and reset control |
90 +-----------+------------+-------------------------------------+
91 | GPIO | on-chip | gpio |
92 +-----------+------------+-------------------------------------+
93 | UART | on-chip | serial |
94 +-----------+------------+-------------------------------------+
95 | TRNG | on-chip | entropy |
96 +-----------+------------+-------------------------------------+
97 | I2C | on-chip | i2c |
98 +-----------+------------+-------------------------------------+
99 | DMA | on-chip | dma controller |
100 +-----------+------------+-------------------------------------+
101 | Watchdog | on-chip | watchdog |
102 +-----------+------------+-------------------------------------+
103 | SPI | on-chip | spi |
104 +-----------+------------+-------------------------------------+
105 | ADC | on-chip | adc |
106 +-----------+------------+-------------------------------------+
107 | Timer | on-chip | counter |
108 +-----------+------------+-------------------------------------+
109 | PWM | on-chip | pwm |
110 +-----------+------------+-------------------------------------+
111 | Flash | on-chip | flash |
112 +-----------+------------+-------------------------------------+
118 +-----------+---------------+---------------+------------------------------------------------------…
122 … | | +-----------+ | +-----------------------------------------------------…
123 | | | | Open | | | Disconnects on-board, high-precision voltage refer…
124 … | | +-----------+ | +-----------------------------------------------------…
125 | | | | Closed | | | Connects on-board, high-precision voltage referenc…
126 … | | +-----------+ | +-----------------------------------------------------…
128 +-----------+---------------+---------------+------------------------------------------------------…
129 …P2 | P0_22 | +-----------+ | +-----------------------------------------------------…
131 … | | +-----------+ | +-----------------------------------------------------…
133 … | | +-----------+ | +-----------------------------------------------------…
135 +-----------+---------------+---------------+------------------------------------------------------…
136 …P3 | P0_23 | +-----------+ | +-----------------------------------------------------…
138 … | | +-----------+ | +-----------------------------------------------------…
140 … | | +-----------+ | +-----------------------------------------------------…
142 +-----------+---------------+---------------+------------------------------------------------------…
143 …P4 | I2C0_SCL | +-----------+ | +-----------------------------------------------------…
145 … | | +-----------+ | +-----------------------------------------------------…
147 … | | +-----------+ | +-----------------------------------------------------…
149 +-----------+---------------+---------------+------------------------------------------------------…
150 …P5 | I2C0_SDA | +-----------+ | +-----------------------------------------------------…
152 … | | +-----------+ | +-----------------------------------------------------…
154 … | | +-----------+ | +-----------------------------------------------------…
156 +-----------+---------------+---------------+------------------------------------------------------…
157 …P6 | I2C1_SCL | +-----------+ | +-----------------------------------------------------…
159 … | | +-----------+ | +-----------------------------------------------------…
161 … | | +-----------+ | +-----------------------------------------------------…
163 +-----------+---------------+---------------+------------------------------------------------------…
164 …P7 | I2C1_SDA | +-----------+ | +-----------------------------------------------------…
166 … | | +-----------+ | +-----------------------------------------------------…
168 … | | +-----------+ | +-----------------------------------------------------…
170 +-----------+---------------+---------------+------------------------------------------------------…
171 …P8 | I2C2_SCL | +-----------+ | +-----------------------------------------------------…
173 … | | +-----------+ | +-----------------------------------------------------…
175 … | | +-----------+ | +-----------------------------------------------------…
177 +-----------+---------------+---------------+------------------------------------------------------…
178 …P9 | I2C2_SDA | +-----------+ | +-----------------------------------------------------…
180 … | | +-----------+ | +-----------------------------------------------------…
182 … | | +-----------+ | +-----------------------------------------------------…
184 +-----------+---------------+---------------+------------------------------------------------------…
185 …P10 | UART_RX | +-----------+ | +-----------------------------------------------------…
186 | | | | 2-1 | | | Connects the USB serial bridge to UART0_RX (P0.8).…
187 … | | +-----------+ | +-----------------------------------------------------…
188 | | | | 2-3 | | | Connects the USB serial bridge to LUART0_RX (P0.26…
189 … | | +-----------+ | +-----------------------------------------------------…
191 +-----------+---------------+---------------+------------------------------------------------------…
192 …P11 | UART_TX | +-----------+ | +-----------------------------------------------------…
193 | | | | 2-1 | | | Connects the USB serial bridge to UART0_TX (P0.9).…
194 … | | +-----------+ | +-----------------------------------------------------…
195 | | | | 2-3 | | | Connects the USB serial bridge to LUART0_TX (P0.27…
196 … | | +-----------+ | +-----------------------------------------------------…
198 +-----------+---------------+---------------+------------------------------------------------------…
199 …P12 | VDDA | +-----------+ | +-----------------------------------------------------…
201 … | | +-----------+ | +-----------------------------------------------------…
203 … | | +-----------+ | +-----------------------------------------------------…
205 +-----------+---------------+---------------+------------------------------------------------------…
206 …P13 | VDD | +-----------+ | +-----------------------------------------------------…
208 … | | +-----------+ | +-----------------------------------------------------…
210 … | | +-----------+ | +-----------------------------------------------------…
212 +-----------+---------------+---------------+------------------------------------------------------…
213 …14 | VCORE | +-----------+ | +------------------------------------------------------…
215 … | | +-----------+ | +------------------------------------------------------…
217 … | | +-----------+ | +------------------------------------------------------…
219 +-----------+---------------+---------------+------------------------------------------------------…
220 …P15 | LDO DUT | +-----------+ | +-----------------------------------------------------…
222 … | | +-----------+ | +-----------------------------------------------------…
224 … | | +-----------+ | +-----------------------------------------------------…
226 +-----------+---------------+---------------+------------------------------------------------------…
235 The EV kit is powered by +5V, which is made available through VBUS on the Micro USB type-B
239 Single- or Dual-Supply Operation
242 The EV kit is configured for single-supply operation. For dual-supply operation,
249 Two pin headers provide convenient current monitoring points for VDDA EN (JP12), VDD EN (JP13),
250 and VCORE EN (JP14). JP14 is only used for current measurements when VCORE is supplied externally.
252 Low-Power Mode Current Measurements
255 To accurately achieve the low-power current values, the EV kit must be configured such that
256 no outside influence (such as a pullup, external clock, or debugger connector) causes
272 The external voltage reference input VREF for the ADC can be sourced externally by a high-precision
280 The EV kit provides a USB-to-UART bridge chip (the FTDI FT230XS-R). This bridge eliminates
281 the requirement for a physical RS-232 COM port. Instead, the IC’s UART access is through
282 the Micro USB type-B connector (CN1). The USB-to-UART bridge can be connected to the IC’s UART0 or
290 The boot loader is activated by the boot-load-enable slide switch (SW2).
291 This pulls P0_10 low and, upon a power cycle or reset, the device will enter boot loader mode.
297 can be accessed through 0.1in-spaced headers J3 and J4.
315 The IC can be reset by pushbutton SW1.
324 SWD debug can be accessed through an Arm Cortex 10-pin connector (J5).
331 pass the ``--erase`` option when executing ``west flash``.
336 a Segger J-Link with Segger's native tooling by overriding the runner,
337 appending ``--runner jlink`` to your ``west`` command(s). The J-Link should
350 - `MAX32672EVKIT web page`_
353 …https://www.analog.com/en/design-center/evaluation-hardware-and-software/evaluation-boards-kits/ma…