1 // SPDX-License-Identifier: GPL-2.0-only
2 /* Copyright (c) 2020, Broadcom */
3 /*
4 * 8250-core based driver for Broadcom ns16550a UARTs
5 *
6 * This driver uses the standard 8250 driver core but adds additional
7 * optional features including the ability to use a baud rate clock
8 * mux for more accurate high speed baud rate selection and also
9 * an optional DMA engine.
10 *
11 */
12
13 #include <linux/module.h>
14 #include <linux/types.h>
15 #include <linux/tty.h>
16 #include <linux/errno.h>
17 #include <linux/device.h>
18 #include <linux/io.h>
19 #include <linux/of.h>
20 #include <linux/dma-mapping.h>
21 #include <linux/tty_flip.h>
22 #include <linux/delay.h>
23 #include <linux/clk.h>
24 #include <linux/debugfs.h>
25
26 #include "8250.h"
27
28 /* Register definitions for UART DMA block. Version 1.1 or later. */
29 #define UDMA_ARB_RX 0x00
30 #define UDMA_ARB_TX 0x04
31 #define UDMA_ARB_REQ 0x00000001
32 #define UDMA_ARB_GRANT 0x00000002
33
34 #define UDMA_RX_REVISION 0x00
35 #define UDMA_RX_REVISION_REQUIRED 0x00000101
36 #define UDMA_RX_CTRL 0x04
37 #define UDMA_RX_CTRL_BUF_CLOSE_MODE 0x00010000
38 #define UDMA_RX_CTRL_MASK_WR_DONE 0x00008000
39 #define UDMA_RX_CTRL_ENDIAN_OVERRIDE 0x00004000
40 #define UDMA_RX_CTRL_ENDIAN 0x00002000
41 #define UDMA_RX_CTRL_OE_IS_ERR 0x00001000
42 #define UDMA_RX_CTRL_PE_IS_ERR 0x00000800
43 #define UDMA_RX_CTRL_FE_IS_ERR 0x00000400
44 #define UDMA_RX_CTRL_NUM_BUF_USED_MASK 0x000003c0
45 #define UDMA_RX_CTRL_NUM_BUF_USED_SHIFT 6
46 #define UDMA_RX_CTRL_BUF_CLOSE_CLK_SEL_SYS 0x00000020
47 #define UDMA_RX_CTRL_BUF_CLOSE_ENA 0x00000010
48 #define UDMA_RX_CTRL_TIMEOUT_CLK_SEL_SYS 0x00000008
49 #define UDMA_RX_CTRL_TIMEOUT_ENA 0x00000004
50 #define UDMA_RX_CTRL_ABORT 0x00000002
51 #define UDMA_RX_CTRL_ENA 0x00000001
52 #define UDMA_RX_STATUS 0x08
53 #define UDMA_RX_STATUS_ACTIVE_BUF_MASK 0x0000000f
54 #define UDMA_RX_TRANSFER_LEN 0x0c
55 #define UDMA_RX_TRANSFER_TOTAL 0x10
56 #define UDMA_RX_BUFFER_SIZE 0x14
57 #define UDMA_RX_SRC_ADDR 0x18
58 #define UDMA_RX_TIMEOUT 0x1c
59 #define UDMA_RX_BUFFER_CLOSE 0x20
60 #define UDMA_RX_BLOCKOUT_COUNTER 0x24
61 #define UDMA_RX_BUF0_PTR_LO 0x28
62 #define UDMA_RX_BUF0_PTR_HI 0x2c
63 #define UDMA_RX_BUF0_STATUS 0x30
64 #define UDMA_RX_BUFX_STATUS_OVERRUN_ERR 0x00000010
65 #define UDMA_RX_BUFX_STATUS_FRAME_ERR 0x00000008
66 #define UDMA_RX_BUFX_STATUS_PARITY_ERR 0x00000004
67 #define UDMA_RX_BUFX_STATUS_CLOSE_EXPIRED 0x00000002
68 #define UDMA_RX_BUFX_STATUS_DATA_RDY 0x00000001
69 #define UDMA_RX_BUF0_DATA_LEN 0x34
70 #define UDMA_RX_BUF1_PTR_LO 0x38
71 #define UDMA_RX_BUF1_PTR_HI 0x3c
72 #define UDMA_RX_BUF1_STATUS 0x40
73 #define UDMA_RX_BUF1_DATA_LEN 0x44
74
75 #define UDMA_TX_REVISION 0x00
76 #define UDMA_TX_REVISION_REQUIRED 0x00000101
77 #define UDMA_TX_CTRL 0x04
78 #define UDMA_TX_CTRL_ENDIAN_OVERRIDE 0x00000080
79 #define UDMA_TX_CTRL_ENDIAN 0x00000040
80 #define UDMA_TX_CTRL_NUM_BUF_USED_MASK 0x00000030
81 #define UDMA_TX_CTRL_NUM_BUF_USED_1 0x00000010
82 #define UDMA_TX_CTRL_ABORT 0x00000002
83 #define UDMA_TX_CTRL_ENA 0x00000001
84 #define UDMA_TX_DST_ADDR 0x08
85 #define UDMA_TX_BLOCKOUT_COUNTER 0x10
86 #define UDMA_TX_TRANSFER_LEN 0x14
87 #define UDMA_TX_TRANSFER_TOTAL 0x18
88 #define UDMA_TX_STATUS 0x20
89 #define UDMA_TX_BUF0_PTR_LO 0x24
90 #define UDMA_TX_BUF0_PTR_HI 0x28
91 #define UDMA_TX_BUF0_STATUS 0x2c
92 #define UDMA_TX_BUFX_LAST 0x00000002
93 #define UDMA_TX_BUFX_EMPTY 0x00000001
94 #define UDMA_TX_BUF0_DATA_LEN 0x30
95 #define UDMA_TX_BUF0_DATA_SENT 0x34
96 #define UDMA_TX_BUF1_PTR_LO 0x38
97
98 #define UDMA_INTR_STATUS 0x00
99 #define UDMA_INTR_ARB_TX_GRANT 0x00040000
100 #define UDMA_INTR_ARB_RX_GRANT 0x00020000
101 #define UDMA_INTR_TX_ALL_EMPTY 0x00010000
102 #define UDMA_INTR_TX_EMPTY_BUF1 0x00008000
103 #define UDMA_INTR_TX_EMPTY_BUF0 0x00004000
104 #define UDMA_INTR_TX_ABORT 0x00002000
105 #define UDMA_INTR_TX_DONE 0x00001000
106 #define UDMA_INTR_RX_ERROR 0x00000800
107 #define UDMA_INTR_RX_TIMEOUT 0x00000400
108 #define UDMA_INTR_RX_READY_BUF7 0x00000200
109 #define UDMA_INTR_RX_READY_BUF6 0x00000100
110 #define UDMA_INTR_RX_READY_BUF5 0x00000080
111 #define UDMA_INTR_RX_READY_BUF4 0x00000040
112 #define UDMA_INTR_RX_READY_BUF3 0x00000020
113 #define UDMA_INTR_RX_READY_BUF2 0x00000010
114 #define UDMA_INTR_RX_READY_BUF1 0x00000008
115 #define UDMA_INTR_RX_READY_BUF0 0x00000004
116 #define UDMA_INTR_RX_READY_MASK 0x000003fc
117 #define UDMA_INTR_RX_READY_SHIFT 2
118 #define UDMA_INTR_RX_ABORT 0x00000002
119 #define UDMA_INTR_RX_DONE 0x00000001
120 #define UDMA_INTR_SET 0x04
121 #define UDMA_INTR_CLEAR 0x08
122 #define UDMA_INTR_MASK_STATUS 0x0c
123 #define UDMA_INTR_MASK_SET 0x10
124 #define UDMA_INTR_MASK_CLEAR 0x14
125
126
127 #define UDMA_RX_INTERRUPTS ( \
128 UDMA_INTR_RX_ERROR | \
129 UDMA_INTR_RX_TIMEOUT | \
130 UDMA_INTR_RX_READY_BUF0 | \
131 UDMA_INTR_RX_READY_BUF1 | \
132 UDMA_INTR_RX_READY_BUF2 | \
133 UDMA_INTR_RX_READY_BUF3 | \
134 UDMA_INTR_RX_READY_BUF4 | \
135 UDMA_INTR_RX_READY_BUF5 | \
136 UDMA_INTR_RX_READY_BUF6 | \
137 UDMA_INTR_RX_READY_BUF7 | \
138 UDMA_INTR_RX_ABORT | \
139 UDMA_INTR_RX_DONE)
140
141 #define UDMA_RX_ERR_INTERRUPTS ( \
142 UDMA_INTR_RX_ERROR | \
143 UDMA_INTR_RX_TIMEOUT | \
144 UDMA_INTR_RX_ABORT | \
145 UDMA_INTR_RX_DONE)
146
147 #define UDMA_TX_INTERRUPTS ( \
148 UDMA_INTR_TX_ABORT | \
149 UDMA_INTR_TX_DONE)
150
151 #define UDMA_IS_RX_INTERRUPT(status) ((status) & UDMA_RX_INTERRUPTS)
152 #define UDMA_IS_TX_INTERRUPT(status) ((status) & UDMA_TX_INTERRUPTS)
153
154
155 /* Current devices have 8 sets of RX buffer registers */
156 #define UDMA_RX_BUFS_COUNT 8
157 #define UDMA_RX_BUFS_REG_OFFSET (UDMA_RX_BUF1_PTR_LO - UDMA_RX_BUF0_PTR_LO)
158 #define UDMA_RX_BUFx_PTR_LO(x) (UDMA_RX_BUF0_PTR_LO + \
159 ((x) * UDMA_RX_BUFS_REG_OFFSET))
160 #define UDMA_RX_BUFx_PTR_HI(x) (UDMA_RX_BUF0_PTR_HI + \
161 ((x) * UDMA_RX_BUFS_REG_OFFSET))
162 #define UDMA_RX_BUFx_STATUS(x) (UDMA_RX_BUF0_STATUS + \
163 ((x) * UDMA_RX_BUFS_REG_OFFSET))
164 #define UDMA_RX_BUFx_DATA_LEN(x) (UDMA_RX_BUF0_DATA_LEN + \
165 ((x) * UDMA_RX_BUFS_REG_OFFSET))
166
167 /* Current devices have 2 sets of TX buffer registers */
168 #define UDMA_TX_BUFS_COUNT 2
169 #define UDMA_TX_BUFS_REG_OFFSET (UDMA_TX_BUF1_PTR_LO - UDMA_TX_BUF0_PTR_LO)
170 #define UDMA_TX_BUFx_PTR_LO(x) (UDMA_TX_BUF0_PTR_LO + \
171 ((x) * UDMA_TX_BUFS_REG_OFFSET))
172 #define UDMA_TX_BUFx_PTR_HI(x) (UDMA_TX_BUF0_PTR_HI + \
173 ((x) * UDMA_TX_BUFS_REG_OFFSET))
174 #define UDMA_TX_BUFx_STATUS(x) (UDMA_TX_BUF0_STATUS + \
175 ((x) * UDMA_TX_BUFS_REG_OFFSET))
176 #define UDMA_TX_BUFx_DATA_LEN(x) (UDMA_TX_BUF0_DATA_LEN + \
177 ((x) * UDMA_TX_BUFS_REG_OFFSET))
178 #define UDMA_TX_BUFx_DATA_SENT(x) (UDMA_TX_BUF0_DATA_SENT + \
179 ((x) * UDMA_TX_BUFS_REG_OFFSET))
180 #define REGS_8250 0
181 #define REGS_DMA_RX 1
182 #define REGS_DMA_TX 2
183 #define REGS_DMA_ISR 3
184 #define REGS_DMA_ARB 4
185 #define REGS_MAX 5
186
187 #define TX_BUF_SIZE 4096
188 #define RX_BUF_SIZE 4096
189 #define RX_BUFS_COUNT 2
190 #define KHZ 1000
191 #define MHZ(x) ((x) * KHZ * KHZ)
192
193 static const u32 brcmstb_rate_table[] = {
194 MHZ(81),
195 MHZ(108),
196 MHZ(64), /* Actually 64285715 for some chips */
197 MHZ(48),
198 };
199
200 static const u32 brcmstb_rate_table_7278[] = {
201 MHZ(81),
202 MHZ(108),
203 0,
204 MHZ(48),
205 };
206
207 struct brcmuart_priv {
208 int line;
209 struct clk *baud_mux_clk;
210 unsigned long default_mux_rate;
211 u32 real_rates[ARRAY_SIZE(brcmstb_rate_table)];
212 const u32 *rate_table;
213 ktime_t char_wait;
214 struct uart_port *up;
215 struct hrtimer hrt;
216 bool shutdown;
217 bool dma_enabled;
218 struct uart_8250_dma dma;
219 void __iomem *regs[REGS_MAX];
220 dma_addr_t rx_addr;
221 void *rx_bufs;
222 size_t rx_size;
223 int rx_next_buf;
224 dma_addr_t tx_addr;
225 void *tx_buf;
226 size_t tx_size;
227 bool tx_running;
228 bool rx_running;
229 struct dentry *debugfs_dir;
230
231 /* stats exposed through debugfs */
232 u64 dma_rx_partial_buf;
233 u64 dma_rx_full_buf;
234 u32 rx_bad_timeout_late_char;
235 u32 rx_bad_timeout_no_char;
236 u32 rx_missing_close_timeout;
237 u32 rx_err;
238 u32 rx_timeout;
239 u32 rx_abort;
240 u32 saved_mctrl;
241 };
242
243 static struct dentry *brcmuart_debugfs_root;
244
245 /*
246 * Register access routines
247 */
udma_readl(struct brcmuart_priv * priv,int reg_type,int offset)248 static u32 udma_readl(struct brcmuart_priv *priv,
249 int reg_type, int offset)
250 {
251 return readl(priv->regs[reg_type] + offset);
252 }
253
udma_writel(struct brcmuart_priv * priv,int reg_type,int offset,u32 value)254 static void udma_writel(struct brcmuart_priv *priv,
255 int reg_type, int offset, u32 value)
256 {
257 writel(value, priv->regs[reg_type] + offset);
258 }
259
udma_set(struct brcmuart_priv * priv,int reg_type,int offset,u32 bits)260 static void udma_set(struct brcmuart_priv *priv,
261 int reg_type, int offset, u32 bits)
262 {
263 void __iomem *reg = priv->regs[reg_type] + offset;
264 u32 value;
265
266 value = readl(reg);
267 value |= bits;
268 writel(value, reg);
269 }
270
udma_unset(struct brcmuart_priv * priv,int reg_type,int offset,u32 bits)271 static void udma_unset(struct brcmuart_priv *priv,
272 int reg_type, int offset, u32 bits)
273 {
274 void __iomem *reg = priv->regs[reg_type] + offset;
275 u32 value;
276
277 value = readl(reg);
278 value &= ~bits;
279 writel(value, reg);
280 }
281
282 /*
283 * The UART DMA engine hardware can be used by multiple UARTS, but
284 * only one at a time. Sharing is not currently supported so
285 * the first UART to request the DMA engine will get it and any
286 * subsequent requests by other UARTS will fail.
287 */
brcmuart_arbitration(struct brcmuart_priv * priv,bool acquire)288 static int brcmuart_arbitration(struct brcmuart_priv *priv, bool acquire)
289 {
290 u32 rx_grant;
291 u32 tx_grant;
292 int waits;
293 int ret = 0;
294
295 if (acquire) {
296 udma_set(priv, REGS_DMA_ARB, UDMA_ARB_RX, UDMA_ARB_REQ);
297 udma_set(priv, REGS_DMA_ARB, UDMA_ARB_TX, UDMA_ARB_REQ);
298
299 waits = 1;
300 while (1) {
301 rx_grant = udma_readl(priv, REGS_DMA_ARB, UDMA_ARB_RX);
302 tx_grant = udma_readl(priv, REGS_DMA_ARB, UDMA_ARB_TX);
303 if (rx_grant & tx_grant & UDMA_ARB_GRANT)
304 return 0;
305 if (waits-- == 0)
306 break;
307 msleep(1);
308 }
309 ret = 1;
310 }
311
312 udma_unset(priv, REGS_DMA_ARB, UDMA_ARB_RX, UDMA_ARB_REQ);
313 udma_unset(priv, REGS_DMA_ARB, UDMA_ARB_TX, UDMA_ARB_REQ);
314 return ret;
315 }
316
brcmuart_init_dma_hardware(struct brcmuart_priv * priv)317 static void brcmuart_init_dma_hardware(struct brcmuart_priv *priv)
318 {
319 u32 daddr;
320 u32 value;
321 int x;
322
323 /* Start with all interrupts disabled */
324 udma_writel(priv, REGS_DMA_ISR, UDMA_INTR_MASK_SET, 0xffffffff);
325
326 udma_writel(priv, REGS_DMA_RX, UDMA_RX_BUFFER_SIZE, RX_BUF_SIZE);
327
328 /*
329 * Setup buffer close to happen when 32 character times have
330 * elapsed since the last character was received.
331 */
332 udma_writel(priv, REGS_DMA_RX, UDMA_RX_BUFFER_CLOSE, 16*10*32);
333 value = (RX_BUFS_COUNT << UDMA_RX_CTRL_NUM_BUF_USED_SHIFT)
334 | UDMA_RX_CTRL_BUF_CLOSE_MODE
335 | UDMA_RX_CTRL_BUF_CLOSE_ENA;
336 udma_writel(priv, REGS_DMA_RX, UDMA_RX_CTRL, value);
337
338 udma_writel(priv, REGS_DMA_RX, UDMA_RX_BLOCKOUT_COUNTER, 0);
339 daddr = priv->rx_addr;
340 for (x = 0; x < RX_BUFS_COUNT; x++) {
341
342 /* Set RX transfer length to 0 for unknown */
343 udma_writel(priv, REGS_DMA_RX, UDMA_RX_TRANSFER_LEN, 0);
344
345 udma_writel(priv, REGS_DMA_RX, UDMA_RX_BUFx_PTR_LO(x),
346 lower_32_bits(daddr));
347 udma_writel(priv, REGS_DMA_RX, UDMA_RX_BUFx_PTR_HI(x),
348 upper_32_bits(daddr));
349 daddr += RX_BUF_SIZE;
350 }
351
352 daddr = priv->tx_addr;
353 udma_writel(priv, REGS_DMA_TX, UDMA_TX_BUFx_PTR_LO(0),
354 lower_32_bits(daddr));
355 udma_writel(priv, REGS_DMA_TX, UDMA_TX_BUFx_PTR_HI(0),
356 upper_32_bits(daddr));
357 udma_writel(priv, REGS_DMA_TX, UDMA_TX_CTRL,
358 UDMA_TX_CTRL_NUM_BUF_USED_1);
359
360 /* clear all interrupts then enable them */
361 udma_writel(priv, REGS_DMA_ISR, UDMA_INTR_CLEAR, 0xffffffff);
362 udma_writel(priv, REGS_DMA_ISR, UDMA_INTR_MASK_CLEAR,
363 UDMA_RX_INTERRUPTS | UDMA_TX_INTERRUPTS);
364
365 }
366
start_rx_dma(struct uart_8250_port * p)367 static void start_rx_dma(struct uart_8250_port *p)
368 {
369 struct brcmuart_priv *priv = p->port.private_data;
370 int x;
371
372 udma_unset(priv, REGS_DMA_RX, UDMA_RX_CTRL, UDMA_RX_CTRL_ENA);
373
374 /* Clear the RX ready bit for all buffers */
375 for (x = 0; x < RX_BUFS_COUNT; x++)
376 udma_unset(priv, REGS_DMA_RX, UDMA_RX_BUFx_STATUS(x),
377 UDMA_RX_BUFX_STATUS_DATA_RDY);
378
379 /* always start with buffer 0 */
380 udma_unset(priv, REGS_DMA_RX, UDMA_RX_STATUS,
381 UDMA_RX_STATUS_ACTIVE_BUF_MASK);
382 priv->rx_next_buf = 0;
383
384 udma_set(priv, REGS_DMA_RX, UDMA_RX_CTRL, UDMA_RX_CTRL_ENA);
385 priv->rx_running = true;
386 }
387
stop_rx_dma(struct uart_8250_port * p)388 static void stop_rx_dma(struct uart_8250_port *p)
389 {
390 struct brcmuart_priv *priv = p->port.private_data;
391
392 /* If RX is running, set the RX ABORT */
393 if (priv->rx_running)
394 udma_set(priv, REGS_DMA_RX, UDMA_RX_CTRL, UDMA_RX_CTRL_ABORT);
395 }
396
stop_tx_dma(struct uart_8250_port * p)397 static int stop_tx_dma(struct uart_8250_port *p)
398 {
399 struct brcmuart_priv *priv = p->port.private_data;
400 u32 value;
401
402 /* If TX is running, set the TX ABORT */
403 value = udma_readl(priv, REGS_DMA_TX, UDMA_TX_CTRL);
404 if (value & UDMA_TX_CTRL_ENA)
405 udma_set(priv, REGS_DMA_TX, UDMA_TX_CTRL, UDMA_TX_CTRL_ABORT);
406 priv->tx_running = false;
407 return 0;
408 }
409
410 /*
411 * NOTE: printk's in this routine will hang the system if this is
412 * the console tty
413 */
brcmuart_tx_dma(struct uart_8250_port * p)414 static int brcmuart_tx_dma(struct uart_8250_port *p)
415 {
416 struct brcmuart_priv *priv = p->port.private_data;
417 struct circ_buf *xmit = &p->port.state->xmit;
418 u32 tx_size;
419
420 if (uart_tx_stopped(&p->port) || priv->tx_running ||
421 uart_circ_empty(xmit)) {
422 return 0;
423 }
424 tx_size = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE);
425
426 priv->dma.tx_err = 0;
427 memcpy(priv->tx_buf, &xmit->buf[xmit->tail], tx_size);
428 uart_xmit_advance(&p->port, tx_size);
429
430 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
431 uart_write_wakeup(&p->port);
432
433 udma_writel(priv, REGS_DMA_TX, UDMA_TX_TRANSFER_LEN, tx_size);
434 udma_writel(priv, REGS_DMA_TX, UDMA_TX_BUF0_DATA_LEN, tx_size);
435 udma_unset(priv, REGS_DMA_TX, UDMA_TX_BUF0_STATUS, UDMA_TX_BUFX_EMPTY);
436 udma_set(priv, REGS_DMA_TX, UDMA_TX_CTRL, UDMA_TX_CTRL_ENA);
437 priv->tx_running = true;
438
439 return 0;
440 }
441
brcmuart_rx_buf_done_isr(struct uart_port * up,int index)442 static void brcmuart_rx_buf_done_isr(struct uart_port *up, int index)
443 {
444 struct brcmuart_priv *priv = up->private_data;
445 struct tty_port *tty_port = &up->state->port;
446 u32 status;
447 u32 length;
448 u32 copied;
449
450 /* Make sure we're still in sync with the hardware */
451 status = udma_readl(priv, REGS_DMA_RX, UDMA_RX_BUFx_STATUS(index));
452 length = udma_readl(priv, REGS_DMA_RX, UDMA_RX_BUFx_DATA_LEN(index));
453
454 if ((status & UDMA_RX_BUFX_STATUS_DATA_RDY) == 0) {
455 dev_err(up->dev, "RX done interrupt but DATA_RDY not found\n");
456 return;
457 }
458 if (status & (UDMA_RX_BUFX_STATUS_OVERRUN_ERR |
459 UDMA_RX_BUFX_STATUS_FRAME_ERR |
460 UDMA_RX_BUFX_STATUS_PARITY_ERR)) {
461 if (status & UDMA_RX_BUFX_STATUS_OVERRUN_ERR) {
462 up->icount.overrun++;
463 dev_warn(up->dev, "RX OVERRUN Error\n");
464 }
465 if (status & UDMA_RX_BUFX_STATUS_FRAME_ERR) {
466 up->icount.frame++;
467 dev_warn(up->dev, "RX FRAMING Error\n");
468 }
469 if (status & UDMA_RX_BUFX_STATUS_PARITY_ERR) {
470 up->icount.parity++;
471 dev_warn(up->dev, "RX PARITY Error\n");
472 }
473 }
474 copied = (u32)tty_insert_flip_string(
475 tty_port,
476 priv->rx_bufs + (index * RX_BUF_SIZE),
477 length);
478 if (copied != length) {
479 dev_warn(up->dev, "Flip buffer overrun of %d bytes\n",
480 length - copied);
481 up->icount.overrun += length - copied;
482 }
483 up->icount.rx += length;
484 if (status & UDMA_RX_BUFX_STATUS_CLOSE_EXPIRED)
485 priv->dma_rx_partial_buf++;
486 else if (length != RX_BUF_SIZE)
487 /*
488 * This is a bug in the controller that doesn't cause
489 * any problems but will be fixed in the future.
490 */
491 priv->rx_missing_close_timeout++;
492 else
493 priv->dma_rx_full_buf++;
494
495 tty_flip_buffer_push(tty_port);
496 }
497
brcmuart_rx_isr(struct uart_port * up,u32 rx_isr)498 static void brcmuart_rx_isr(struct uart_port *up, u32 rx_isr)
499 {
500 struct brcmuart_priv *priv = up->private_data;
501 struct device *dev = up->dev;
502 u32 rx_done_isr;
503 u32 check_isr;
504
505 rx_done_isr = (rx_isr & UDMA_INTR_RX_READY_MASK);
506 while (rx_done_isr) {
507 check_isr = UDMA_INTR_RX_READY_BUF0 << priv->rx_next_buf;
508 if (check_isr & rx_done_isr) {
509 brcmuart_rx_buf_done_isr(up, priv->rx_next_buf);
510 } else {
511 dev_err(dev,
512 "RX buffer ready out of sequence, restarting RX DMA\n");
513 start_rx_dma(up_to_u8250p(up));
514 break;
515 }
516 if (rx_isr & UDMA_RX_ERR_INTERRUPTS) {
517 if (rx_isr & UDMA_INTR_RX_ERROR)
518 priv->rx_err++;
519 if (rx_isr & UDMA_INTR_RX_TIMEOUT) {
520 priv->rx_timeout++;
521 dev_err(dev, "RX TIMEOUT Error\n");
522 }
523 if (rx_isr & UDMA_INTR_RX_ABORT)
524 priv->rx_abort++;
525 priv->rx_running = false;
526 }
527 /* If not ABORT, re-enable RX buffer */
528 if (!(rx_isr & UDMA_INTR_RX_ABORT))
529 udma_unset(priv, REGS_DMA_RX,
530 UDMA_RX_BUFx_STATUS(priv->rx_next_buf),
531 UDMA_RX_BUFX_STATUS_DATA_RDY);
532 rx_done_isr &= ~check_isr;
533 priv->rx_next_buf++;
534 if (priv->rx_next_buf == RX_BUFS_COUNT)
535 priv->rx_next_buf = 0;
536 }
537 }
538
brcmuart_tx_isr(struct uart_port * up,u32 isr)539 static void brcmuart_tx_isr(struct uart_port *up, u32 isr)
540 {
541 struct brcmuart_priv *priv = up->private_data;
542 struct device *dev = up->dev;
543 struct uart_8250_port *port_8250 = up_to_u8250p(up);
544 struct circ_buf *xmit = &port_8250->port.state->xmit;
545
546 if (isr & UDMA_INTR_TX_ABORT) {
547 if (priv->tx_running)
548 dev_err(dev, "Unexpected TX_ABORT interrupt\n");
549 return;
550 }
551 priv->tx_running = false;
552 if (!uart_circ_empty(xmit) && !uart_tx_stopped(up))
553 brcmuart_tx_dma(port_8250);
554 }
555
brcmuart_isr(int irq,void * dev_id)556 static irqreturn_t brcmuart_isr(int irq, void *dev_id)
557 {
558 struct uart_port *up = dev_id;
559 struct device *dev = up->dev;
560 struct brcmuart_priv *priv = up->private_data;
561 unsigned long flags;
562 u32 interrupts;
563 u32 rval;
564 u32 tval;
565
566 interrupts = udma_readl(priv, REGS_DMA_ISR, UDMA_INTR_STATUS);
567 if (interrupts == 0)
568 return IRQ_NONE;
569
570 spin_lock_irqsave(&up->lock, flags);
571
572 /* Clear all interrupts */
573 udma_writel(priv, REGS_DMA_ISR, UDMA_INTR_CLEAR, interrupts);
574
575 rval = UDMA_IS_RX_INTERRUPT(interrupts);
576 if (rval)
577 brcmuart_rx_isr(up, rval);
578 tval = UDMA_IS_TX_INTERRUPT(interrupts);
579 if (tval)
580 brcmuart_tx_isr(up, tval);
581 if ((rval | tval) == 0)
582 dev_warn(dev, "Spurious interrupt: 0x%x\n", interrupts);
583
584 spin_unlock_irqrestore(&up->lock, flags);
585 return IRQ_HANDLED;
586 }
587
brcmuart_startup(struct uart_port * port)588 static int brcmuart_startup(struct uart_port *port)
589 {
590 int res;
591 struct uart_8250_port *up = up_to_u8250p(port);
592 struct brcmuart_priv *priv = up->port.private_data;
593
594 priv->shutdown = false;
595
596 /*
597 * prevent serial8250_do_startup() from allocating non-existent
598 * DMA resources
599 */
600 up->dma = NULL;
601
602 res = serial8250_do_startup(port);
603 if (!priv->dma_enabled)
604 return res;
605 /*
606 * Disable the Receive Data Interrupt because the DMA engine
607 * will handle this.
608 *
609 * Synchronize UART_IER access against the console.
610 */
611 spin_lock_irq(&port->lock);
612 up->ier &= ~UART_IER_RDI;
613 serial_port_out(port, UART_IER, up->ier);
614 spin_unlock_irq(&port->lock);
615
616 priv->tx_running = false;
617 priv->dma.rx_dma = NULL;
618 priv->dma.tx_dma = brcmuart_tx_dma;
619 up->dma = &priv->dma;
620
621 brcmuart_init_dma_hardware(priv);
622 start_rx_dma(up);
623 return res;
624 }
625
brcmuart_shutdown(struct uart_port * port)626 static void brcmuart_shutdown(struct uart_port *port)
627 {
628 struct uart_8250_port *up = up_to_u8250p(port);
629 struct brcmuart_priv *priv = up->port.private_data;
630 unsigned long flags;
631
632 spin_lock_irqsave(&port->lock, flags);
633 priv->shutdown = true;
634 if (priv->dma_enabled) {
635 stop_rx_dma(up);
636 stop_tx_dma(up);
637 /* disable all interrupts */
638 udma_writel(priv, REGS_DMA_ISR, UDMA_INTR_MASK_SET,
639 UDMA_RX_INTERRUPTS | UDMA_TX_INTERRUPTS);
640 }
641
642 /*
643 * prevent serial8250_do_shutdown() from trying to free
644 * DMA resources that we never alloc'd for this driver.
645 */
646 up->dma = NULL;
647
648 spin_unlock_irqrestore(&port->lock, flags);
649 serial8250_do_shutdown(port);
650 }
651
652 /*
653 * Not all clocks run at the exact specified rate, so set each requested
654 * rate and then get the actual rate.
655 */
init_real_clk_rates(struct device * dev,struct brcmuart_priv * priv)656 static void init_real_clk_rates(struct device *dev, struct brcmuart_priv *priv)
657 {
658 int x;
659 int rc;
660
661 priv->default_mux_rate = clk_get_rate(priv->baud_mux_clk);
662 for (x = 0; x < ARRAY_SIZE(priv->real_rates); x++) {
663 if (priv->rate_table[x] == 0) {
664 priv->real_rates[x] = 0;
665 continue;
666 }
667 rc = clk_set_rate(priv->baud_mux_clk, priv->rate_table[x]);
668 if (rc) {
669 dev_err(dev, "Error selecting BAUD MUX clock for %u\n",
670 priv->rate_table[x]);
671 priv->real_rates[x] = priv->rate_table[x];
672 } else {
673 priv->real_rates[x] = clk_get_rate(priv->baud_mux_clk);
674 }
675 }
676 clk_set_rate(priv->baud_mux_clk, priv->default_mux_rate);
677 }
678
set_clock_mux(struct uart_port * up,struct brcmuart_priv * priv,u32 baud)679 static void set_clock_mux(struct uart_port *up, struct brcmuart_priv *priv,
680 u32 baud)
681 {
682 u32 percent;
683 u32 best_percent = UINT_MAX;
684 u32 quot;
685 u32 best_quot = 1;
686 u32 rate;
687 int best_index = -1;
688 u64 hires_rate;
689 u64 hires_baud;
690 u64 hires_err;
691 int rc;
692 int i;
693 int real_baud;
694
695 /* If the Baud Mux Clock was not specified, just return */
696 if (priv->baud_mux_clk == NULL)
697 return;
698
699 /* Find the closest match for specified baud */
700 for (i = 0; i < ARRAY_SIZE(priv->real_rates); i++) {
701 if (priv->real_rates[i] == 0)
702 continue;
703 rate = priv->real_rates[i] / 16;
704 quot = DIV_ROUND_CLOSEST(rate, baud);
705 if (!quot)
706 continue;
707
708 /* increase resolution to get xx.xx percent */
709 hires_rate = (u64)rate * 10000;
710 hires_baud = (u64)baud * 10000;
711
712 hires_err = div_u64(hires_rate, (u64)quot);
713
714 /* get the delta */
715 if (hires_err > hires_baud)
716 hires_err = (hires_err - hires_baud);
717 else
718 hires_err = (hires_baud - hires_err);
719
720 percent = (unsigned long)DIV_ROUND_CLOSEST_ULL(hires_err, baud);
721 dev_dbg(up->dev,
722 "Baud rate: %u, MUX Clk: %u, Error: %u.%u%%\n",
723 baud, priv->real_rates[i], percent / 100,
724 percent % 100);
725 if (percent < best_percent) {
726 best_percent = percent;
727 best_index = i;
728 best_quot = quot;
729 }
730 }
731 if (best_index == -1) {
732 dev_err(up->dev, "Error, %d BAUD rate is too fast.\n", baud);
733 return;
734 }
735 rate = priv->real_rates[best_index];
736 rc = clk_set_rate(priv->baud_mux_clk, rate);
737 if (rc)
738 dev_err(up->dev, "Error selecting BAUD MUX clock\n");
739
740 /* Error over 3 percent will cause data errors */
741 if (best_percent > 300)
742 dev_err(up->dev, "Error, baud: %d has %u.%u%% error\n",
743 baud, percent / 100, percent % 100);
744
745 real_baud = rate / 16 / best_quot;
746 dev_dbg(up->dev, "Selecting BAUD MUX rate: %u\n", rate);
747 dev_dbg(up->dev, "Requested baud: %u, Actual baud: %u\n",
748 baud, real_baud);
749
750 /* calc nanoseconds for 1.5 characters time at the given baud rate */
751 i = NSEC_PER_SEC / real_baud / 10;
752 i += (i / 2);
753 priv->char_wait = ns_to_ktime(i);
754
755 up->uartclk = rate;
756 }
757
brcmstb_set_termios(struct uart_port * up,struct ktermios * termios,const struct ktermios * old)758 static void brcmstb_set_termios(struct uart_port *up,
759 struct ktermios *termios,
760 const struct ktermios *old)
761 {
762 struct uart_8250_port *p8250 = up_to_u8250p(up);
763 struct brcmuart_priv *priv = up->private_data;
764
765 if (priv->dma_enabled)
766 stop_rx_dma(p8250);
767 set_clock_mux(up, priv, tty_termios_baud_rate(termios));
768 serial8250_do_set_termios(up, termios, old);
769 if (p8250->mcr & UART_MCR_AFE)
770 p8250->port.status |= UPSTAT_AUTOCTS;
771 if (priv->dma_enabled)
772 start_rx_dma(p8250);
773 }
774
brcmuart_handle_irq(struct uart_port * p)775 static int brcmuart_handle_irq(struct uart_port *p)
776 {
777 unsigned int iir = serial_port_in(p, UART_IIR);
778 struct brcmuart_priv *priv = p->private_data;
779 struct uart_8250_port *up = up_to_u8250p(p);
780 unsigned int status;
781 unsigned long flags;
782 unsigned int ier;
783 unsigned int mcr;
784 int handled = 0;
785
786 /*
787 * There's a bug in some 8250 cores where we get a timeout
788 * interrupt but there is no data ready.
789 */
790 if (((iir & UART_IIR_ID) == UART_IIR_RX_TIMEOUT) && !(priv->shutdown)) {
791 spin_lock_irqsave(&p->lock, flags);
792 status = serial_port_in(p, UART_LSR);
793 if ((status & UART_LSR_DR) == 0) {
794
795 ier = serial_port_in(p, UART_IER);
796 /*
797 * if Receive Data Interrupt is enabled and
798 * we're uing hardware flow control, deassert
799 * RTS and wait for any chars in the pipline to
800 * arrive and then check for DR again.
801 */
802 if ((ier & UART_IER_RDI) && (up->mcr & UART_MCR_AFE)) {
803 ier &= ~(UART_IER_RLSI | UART_IER_RDI);
804 serial_port_out(p, UART_IER, ier);
805 mcr = serial_port_in(p, UART_MCR);
806 mcr &= ~UART_MCR_RTS;
807 serial_port_out(p, UART_MCR, mcr);
808 hrtimer_start(&priv->hrt, priv->char_wait,
809 HRTIMER_MODE_REL);
810 } else {
811 serial_port_in(p, UART_RX);
812 }
813
814 handled = 1;
815 }
816 spin_unlock_irqrestore(&p->lock, flags);
817 if (handled)
818 return 1;
819 }
820 return serial8250_handle_irq(p, iir);
821 }
822
brcmuart_hrtimer_func(struct hrtimer * t)823 static enum hrtimer_restart brcmuart_hrtimer_func(struct hrtimer *t)
824 {
825 struct brcmuart_priv *priv = container_of(t, struct brcmuart_priv, hrt);
826 struct uart_port *p = priv->up;
827 struct uart_8250_port *up = up_to_u8250p(p);
828 unsigned int status;
829 unsigned long flags;
830
831 if (priv->shutdown)
832 return HRTIMER_NORESTART;
833
834 spin_lock_irqsave(&p->lock, flags);
835 status = serial_port_in(p, UART_LSR);
836
837 /*
838 * If a character did not arrive after the timeout, clear the false
839 * receive timeout.
840 */
841 if ((status & UART_LSR_DR) == 0) {
842 serial_port_in(p, UART_RX);
843 priv->rx_bad_timeout_no_char++;
844 } else {
845 priv->rx_bad_timeout_late_char++;
846 }
847
848 /* re-enable receive unless upper layer has disabled it */
849 if ((up->ier & (UART_IER_RLSI | UART_IER_RDI)) ==
850 (UART_IER_RLSI | UART_IER_RDI)) {
851 status = serial_port_in(p, UART_IER);
852 status |= (UART_IER_RLSI | UART_IER_RDI);
853 serial_port_out(p, UART_IER, status);
854 status = serial_port_in(p, UART_MCR);
855 status |= UART_MCR_RTS;
856 serial_port_out(p, UART_MCR, status);
857 }
858 spin_unlock_irqrestore(&p->lock, flags);
859 return HRTIMER_NORESTART;
860 }
861
862 static const struct of_device_id brcmuart_dt_ids[] = {
863 {
864 .compatible = "brcm,bcm7278-uart",
865 .data = brcmstb_rate_table_7278,
866 },
867 {
868 .compatible = "brcm,bcm7271-uart",
869 .data = brcmstb_rate_table,
870 },
871 {},
872 };
873
874 MODULE_DEVICE_TABLE(of, brcmuart_dt_ids);
875
brcmuart_free_bufs(struct device * dev,struct brcmuart_priv * priv)876 static void brcmuart_free_bufs(struct device *dev, struct brcmuart_priv *priv)
877 {
878 if (priv->rx_bufs)
879 dma_free_coherent(dev, priv->rx_size, priv->rx_bufs,
880 priv->rx_addr);
881 if (priv->tx_buf)
882 dma_free_coherent(dev, priv->tx_size, priv->tx_buf,
883 priv->tx_addr);
884 }
885
brcmuart_throttle(struct uart_port * port)886 static void brcmuart_throttle(struct uart_port *port)
887 {
888 struct brcmuart_priv *priv = port->private_data;
889
890 udma_writel(priv, REGS_DMA_ISR, UDMA_INTR_MASK_SET, UDMA_RX_INTERRUPTS);
891 }
892
brcmuart_unthrottle(struct uart_port * port)893 static void brcmuart_unthrottle(struct uart_port *port)
894 {
895 struct brcmuart_priv *priv = port->private_data;
896
897 udma_writel(priv, REGS_DMA_ISR, UDMA_INTR_MASK_CLEAR,
898 UDMA_RX_INTERRUPTS);
899 }
900
debugfs_stats_show(struct seq_file * s,void * unused)901 static int debugfs_stats_show(struct seq_file *s, void *unused)
902 {
903 struct brcmuart_priv *priv = s->private;
904
905 seq_printf(s, "rx_err:\t\t\t\t%u\n",
906 priv->rx_err);
907 seq_printf(s, "rx_timeout:\t\t\t%u\n",
908 priv->rx_timeout);
909 seq_printf(s, "rx_abort:\t\t\t%u\n",
910 priv->rx_abort);
911 seq_printf(s, "rx_bad_timeout_late_char:\t%u\n",
912 priv->rx_bad_timeout_late_char);
913 seq_printf(s, "rx_bad_timeout_no_char:\t\t%u\n",
914 priv->rx_bad_timeout_no_char);
915 seq_printf(s, "rx_missing_close_timeout:\t%u\n",
916 priv->rx_missing_close_timeout);
917 if (priv->dma_enabled) {
918 seq_printf(s, "dma_rx_partial_buf:\t\t%llu\n",
919 priv->dma_rx_partial_buf);
920 seq_printf(s, "dma_rx_full_buf:\t\t%llu\n",
921 priv->dma_rx_full_buf);
922 }
923 return 0;
924 }
925 DEFINE_SHOW_ATTRIBUTE(debugfs_stats);
926
brcmuart_init_debugfs(struct brcmuart_priv * priv,const char * device)927 static void brcmuart_init_debugfs(struct brcmuart_priv *priv,
928 const char *device)
929 {
930 priv->debugfs_dir = debugfs_create_dir(device, brcmuart_debugfs_root);
931 debugfs_create_file("stats", 0444, priv->debugfs_dir, priv,
932 &debugfs_stats_fops);
933 }
934
935
brcmuart_probe(struct platform_device * pdev)936 static int brcmuart_probe(struct platform_device *pdev)
937 {
938 struct resource *regs;
939 struct device_node *np = pdev->dev.of_node;
940 const struct of_device_id *of_id = NULL;
941 struct uart_8250_port *new_port;
942 struct device *dev = &pdev->dev;
943 struct brcmuart_priv *priv;
944 struct clk *baud_mux_clk;
945 struct uart_8250_port up;
946 int irq;
947 void __iomem *membase = NULL;
948 resource_size_t mapbase = 0;
949 u32 clk_rate = 0;
950 int ret;
951 int x;
952 int dma_irq;
953 static const char * const reg_names[REGS_MAX] = {
954 "uart", "dma_rx", "dma_tx", "dma_intr2", "dma_arb"
955 };
956
957 irq = platform_get_irq(pdev, 0);
958 if (irq < 0)
959 return irq;
960 priv = devm_kzalloc(dev, sizeof(struct brcmuart_priv),
961 GFP_KERNEL);
962 if (!priv)
963 return -ENOMEM;
964
965 of_id = of_match_node(brcmuart_dt_ids, np);
966 if (!of_id || !of_id->data)
967 priv->rate_table = brcmstb_rate_table;
968 else
969 priv->rate_table = of_id->data;
970
971 for (x = 0; x < REGS_MAX; x++) {
972 regs = platform_get_resource_byname(pdev, IORESOURCE_MEM,
973 reg_names[x]);
974 if (!regs)
975 break;
976 priv->regs[x] = devm_ioremap(dev, regs->start,
977 resource_size(regs));
978 if (!priv->regs[x])
979 return -ENOMEM;
980 if (x == REGS_8250) {
981 mapbase = regs->start;
982 membase = priv->regs[x];
983 }
984 }
985
986 /* We should have just the uart base registers or all the registers */
987 if (x != 1 && x != REGS_MAX) {
988 dev_warn(dev, "%s registers not specified\n", reg_names[x]);
989 return -EINVAL;
990 }
991
992 /* if the DMA registers were specified, try to enable DMA */
993 if (x > REGS_DMA_RX) {
994 if (brcmuart_arbitration(priv, 1) == 0) {
995 u32 txrev = 0;
996 u32 rxrev = 0;
997
998 txrev = udma_readl(priv, REGS_DMA_RX, UDMA_RX_REVISION);
999 rxrev = udma_readl(priv, REGS_DMA_TX, UDMA_TX_REVISION);
1000 if ((txrev >= UDMA_TX_REVISION_REQUIRED) &&
1001 (rxrev >= UDMA_RX_REVISION_REQUIRED)) {
1002
1003 /* Enable the use of the DMA hardware */
1004 priv->dma_enabled = true;
1005 } else {
1006 brcmuart_arbitration(priv, 0);
1007 dev_err(dev,
1008 "Unsupported DMA Hardware Revision\n");
1009 }
1010 } else {
1011 dev_err(dev,
1012 "Timeout arbitrating for UART DMA hardware\n");
1013 }
1014 }
1015
1016 of_property_read_u32(np, "clock-frequency", &clk_rate);
1017
1018 /* See if a Baud clock has been specified */
1019 baud_mux_clk = devm_clk_get(dev, "sw_baud");
1020 if (IS_ERR(baud_mux_clk)) {
1021 if (PTR_ERR(baud_mux_clk) == -EPROBE_DEFER) {
1022 ret = -EPROBE_DEFER;
1023 goto release_dma;
1024 }
1025 dev_dbg(dev, "BAUD MUX clock not specified\n");
1026 } else {
1027 dev_dbg(dev, "BAUD MUX clock found\n");
1028 ret = clk_prepare_enable(baud_mux_clk);
1029 if (ret)
1030 goto release_dma;
1031 priv->baud_mux_clk = baud_mux_clk;
1032 init_real_clk_rates(dev, priv);
1033 clk_rate = priv->default_mux_rate;
1034 }
1035
1036 if (clk_rate == 0) {
1037 dev_err(dev, "clock-frequency or clk not defined\n");
1038 ret = -EINVAL;
1039 goto err_clk_disable;
1040 }
1041
1042 dev_dbg(dev, "DMA is %senabled\n", priv->dma_enabled ? "" : "not ");
1043
1044 memset(&up, 0, sizeof(up));
1045 up.port.type = PORT_BCM7271;
1046 up.port.uartclk = clk_rate;
1047 up.port.dev = dev;
1048 up.port.mapbase = mapbase;
1049 up.port.membase = membase;
1050 up.port.irq = irq;
1051 up.port.handle_irq = brcmuart_handle_irq;
1052 up.port.regshift = 2;
1053 up.port.iotype = of_device_is_big_endian(np) ?
1054 UPIO_MEM32BE : UPIO_MEM32;
1055 up.port.flags = UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF
1056 | UPF_FIXED_PORT | UPF_FIXED_TYPE;
1057 up.port.dev = dev;
1058 up.port.private_data = priv;
1059
1060 /* Check for a fixed line number */
1061 ret = of_alias_get_id(np, "serial");
1062 if (ret >= 0)
1063 up.port.line = ret;
1064
1065 /* setup HR timer */
1066 hrtimer_init(&priv->hrt, CLOCK_MONOTONIC, HRTIMER_MODE_ABS);
1067 priv->hrt.function = brcmuart_hrtimer_func;
1068
1069 up.port.shutdown = brcmuart_shutdown;
1070 up.port.startup = brcmuart_startup;
1071 up.port.throttle = brcmuart_throttle;
1072 up.port.unthrottle = brcmuart_unthrottle;
1073 up.port.set_termios = brcmstb_set_termios;
1074
1075 if (priv->dma_enabled) {
1076 priv->rx_size = RX_BUF_SIZE * RX_BUFS_COUNT;
1077 priv->rx_bufs = dma_alloc_coherent(dev,
1078 priv->rx_size,
1079 &priv->rx_addr, GFP_KERNEL);
1080 if (!priv->rx_bufs) {
1081 ret = -ENOMEM;
1082 goto err;
1083 }
1084 priv->tx_size = UART_XMIT_SIZE;
1085 priv->tx_buf = dma_alloc_coherent(dev,
1086 priv->tx_size,
1087 &priv->tx_addr, GFP_KERNEL);
1088 if (!priv->tx_buf) {
1089 ret = -ENOMEM;
1090 goto err;
1091 }
1092 }
1093
1094 ret = serial8250_register_8250_port(&up);
1095 if (ret < 0) {
1096 dev_err(dev, "unable to register 8250 port\n");
1097 goto err;
1098 }
1099 priv->line = ret;
1100 new_port = serial8250_get_port(ret);
1101 priv->up = &new_port->port;
1102 if (priv->dma_enabled) {
1103 dma_irq = platform_get_irq_byname(pdev, "dma");
1104 if (dma_irq < 0) {
1105 ret = dma_irq;
1106 dev_err(dev, "no IRQ resource info\n");
1107 goto err1;
1108 }
1109 ret = devm_request_irq(dev, dma_irq, brcmuart_isr,
1110 IRQF_SHARED, "uart DMA irq", &new_port->port);
1111 if (ret) {
1112 dev_err(dev, "unable to register IRQ handler\n");
1113 goto err1;
1114 }
1115 }
1116 platform_set_drvdata(pdev, priv);
1117 brcmuart_init_debugfs(priv, dev_name(&pdev->dev));
1118 return 0;
1119
1120 err1:
1121 serial8250_unregister_port(priv->line);
1122 err:
1123 brcmuart_free_bufs(dev, priv);
1124 err_clk_disable:
1125 clk_disable_unprepare(baud_mux_clk);
1126 release_dma:
1127 if (priv->dma_enabled)
1128 brcmuart_arbitration(priv, 0);
1129 return ret;
1130 }
1131
brcmuart_remove(struct platform_device * pdev)1132 static int brcmuart_remove(struct platform_device *pdev)
1133 {
1134 struct brcmuart_priv *priv = platform_get_drvdata(pdev);
1135
1136 debugfs_remove_recursive(priv->debugfs_dir);
1137 hrtimer_cancel(&priv->hrt);
1138 serial8250_unregister_port(priv->line);
1139 brcmuart_free_bufs(&pdev->dev, priv);
1140 clk_disable_unprepare(priv->baud_mux_clk);
1141 if (priv->dma_enabled)
1142 brcmuart_arbitration(priv, 0);
1143 return 0;
1144 }
1145
brcmuart_suspend(struct device * dev)1146 static int __maybe_unused brcmuart_suspend(struct device *dev)
1147 {
1148 struct brcmuart_priv *priv = dev_get_drvdata(dev);
1149 struct uart_8250_port *up = serial8250_get_port(priv->line);
1150 struct uart_port *port = &up->port;
1151 unsigned long flags;
1152
1153 /*
1154 * This will prevent resume from enabling RTS before the
1155 * baud rate has been restored.
1156 */
1157 spin_lock_irqsave(&port->lock, flags);
1158 priv->saved_mctrl = port->mctrl;
1159 port->mctrl &= ~TIOCM_RTS;
1160 spin_unlock_irqrestore(&port->lock, flags);
1161
1162 serial8250_suspend_port(priv->line);
1163 clk_disable_unprepare(priv->baud_mux_clk);
1164
1165 return 0;
1166 }
1167
brcmuart_resume(struct device * dev)1168 static int __maybe_unused brcmuart_resume(struct device *dev)
1169 {
1170 struct brcmuart_priv *priv = dev_get_drvdata(dev);
1171 struct uart_8250_port *up = serial8250_get_port(priv->line);
1172 struct uart_port *port = &up->port;
1173 unsigned long flags;
1174 int ret;
1175
1176 ret = clk_prepare_enable(priv->baud_mux_clk);
1177 if (ret)
1178 dev_err(dev, "Error enabling BAUD MUX clock\n");
1179
1180 /*
1181 * The hardware goes back to it's default after suspend
1182 * so get the "clk" back in sync.
1183 */
1184 ret = clk_set_rate(priv->baud_mux_clk, priv->default_mux_rate);
1185 if (ret)
1186 dev_err(dev, "Error restoring default BAUD MUX clock\n");
1187 if (priv->dma_enabled) {
1188 if (brcmuart_arbitration(priv, 1)) {
1189 dev_err(dev, "Timeout arbitrating for DMA hardware on resume\n");
1190 return(-EBUSY);
1191 }
1192 brcmuart_init_dma_hardware(priv);
1193 start_rx_dma(serial8250_get_port(priv->line));
1194 }
1195 serial8250_resume_port(priv->line);
1196
1197 if (priv->saved_mctrl & TIOCM_RTS) {
1198 /* Restore RTS */
1199 spin_lock_irqsave(&port->lock, flags);
1200 port->mctrl |= TIOCM_RTS;
1201 port->ops->set_mctrl(port, port->mctrl);
1202 spin_unlock_irqrestore(&port->lock, flags);
1203 }
1204
1205 return 0;
1206 }
1207
1208 static const struct dev_pm_ops brcmuart_dev_pm_ops = {
1209 SET_SYSTEM_SLEEP_PM_OPS(brcmuart_suspend, brcmuart_resume)
1210 };
1211
1212 static struct platform_driver brcmuart_platform_driver = {
1213 .driver = {
1214 .name = "bcm7271-uart",
1215 .pm = &brcmuart_dev_pm_ops,
1216 .of_match_table = brcmuart_dt_ids,
1217 },
1218 .probe = brcmuart_probe,
1219 .remove = brcmuart_remove,
1220 };
1221
brcmuart_init(void)1222 static int __init brcmuart_init(void)
1223 {
1224 int ret;
1225
1226 brcmuart_debugfs_root = debugfs_create_dir(
1227 brcmuart_platform_driver.driver.name, NULL);
1228 ret = platform_driver_register(&brcmuart_platform_driver);
1229 if (ret) {
1230 debugfs_remove_recursive(brcmuart_debugfs_root);
1231 return ret;
1232 }
1233
1234 return 0;
1235 }
1236 module_init(brcmuart_init);
1237
brcmuart_deinit(void)1238 static void __exit brcmuart_deinit(void)
1239 {
1240 platform_driver_unregister(&brcmuart_platform_driver);
1241 debugfs_remove_recursive(brcmuart_debugfs_root);
1242 }
1243 module_exit(brcmuart_deinit);
1244
1245 MODULE_AUTHOR("Al Cooper");
1246 MODULE_DESCRIPTION("Broadcom NS16550A compatible serial port driver");
1247 MODULE_LICENSE("GPL v2");
1248
