1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * Driver for ADC module on the Cirrus Logic EP93xx series of SoCs
4 *
5 * Copyright (C) 2015 Alexander Sverdlin
6 *
7 * The driver uses polling to get the conversion status. According to EP93xx
8 * datasheets, reading ADCResult register starts the conversion, but user is also
9 * responsible for ensuring that delay between adjacent conversion triggers is
10 * long enough so that maximum allowed conversion rate is not exceeded. This
11 * basically renders IRQ mode unusable.
12 */
13
14 #include <linux/clk.h>
15 #include <linux/delay.h>
16 #include <linux/device.h>
17 #include <linux/err.h>
18 #include <linux/iio/iio.h>
19 #include <linux/io.h>
20 #include <linux/irqflags.h>
21 #include <linux/module.h>
22 #include <linux/mutex.h>
23 #include <linux/platform_device.h>
24 #include <linux/of.h>
25
26 /*
27 * This code could benefit from real HR Timers, but jiffy granularity would
28 * lower ADC conversion rate down to CONFIG_HZ, so we fallback to busy wait
29 * in such case.
30 *
31 * HR Timers-based version loads CPU only up to 10% during back to back ADC
32 * conversion, while busy wait-based version consumes whole CPU power.
33 */
34 #ifdef CONFIG_HIGH_RES_TIMERS
35 #define ep93xx_adc_delay(usmin, usmax) usleep_range(usmin, usmax)
36 #else
37 #define ep93xx_adc_delay(usmin, usmax) udelay(usmin)
38 #endif
39
40 #define EP93XX_ADC_RESULT 0x08
41 #define EP93XX_ADC_SDR BIT(31)
42 #define EP93XX_ADC_SWITCH 0x18
43 #define EP93XX_ADC_SW_LOCK 0x20
44
45 struct ep93xx_adc_priv {
46 struct clk *clk;
47 void __iomem *base;
48 int lastch;
49 struct mutex lock;
50 };
51
52 #define EP93XX_ADC_CH(index, dname, swcfg) { \
53 .type = IIO_VOLTAGE, \
54 .indexed = 1, \
55 .channel = index, \
56 .address = swcfg, \
57 .datasheet_name = dname, \
58 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \
59 .info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SCALE) | \
60 BIT(IIO_CHAN_INFO_OFFSET), \
61 }
62
63 /*
64 * Numbering scheme for channels 0..4 is defined in EP9301 and EP9302 datasheets.
65 * EP9307, EP9312 and EP9312 have 3 channels more (total 8), but the numbering is
66 * not defined. So the last three are numbered randomly, let's say.
67 */
68 static const struct iio_chan_spec ep93xx_adc_channels[8] = {
69 EP93XX_ADC_CH(0, "YM", 0x608),
70 EP93XX_ADC_CH(1, "SXP", 0x680),
71 EP93XX_ADC_CH(2, "SXM", 0x640),
72 EP93XX_ADC_CH(3, "SYP", 0x620),
73 EP93XX_ADC_CH(4, "SYM", 0x610),
74 EP93XX_ADC_CH(5, "XP", 0x601),
75 EP93XX_ADC_CH(6, "XM", 0x602),
76 EP93XX_ADC_CH(7, "YP", 0x604),
77 };
78
ep93xx_read_raw(struct iio_dev * iiodev,struct iio_chan_spec const * channel,int * value,int * shift,long mask)79 static int ep93xx_read_raw(struct iio_dev *iiodev,
80 struct iio_chan_spec const *channel, int *value,
81 int *shift, long mask)
82 {
83 struct ep93xx_adc_priv *priv = iio_priv(iiodev);
84 unsigned long timeout;
85 int ret;
86
87 switch (mask) {
88 case IIO_CHAN_INFO_RAW:
89 mutex_lock(&priv->lock);
90 if (priv->lastch != channel->channel) {
91 priv->lastch = channel->channel;
92 /*
93 * Switch register is software-locked, unlocking must be
94 * immediately followed by write
95 */
96 local_irq_disable();
97 writel_relaxed(0xAA, priv->base + EP93XX_ADC_SW_LOCK);
98 writel_relaxed(channel->address,
99 priv->base + EP93XX_ADC_SWITCH);
100 local_irq_enable();
101 /*
102 * Settling delay depends on module clock and could be
103 * 2ms or 500us
104 */
105 ep93xx_adc_delay(2000, 2000);
106 }
107 /* Start the conversion, eventually discarding old result */
108 readl_relaxed(priv->base + EP93XX_ADC_RESULT);
109 /* Ensure maximum conversion rate is not exceeded */
110 ep93xx_adc_delay(DIV_ROUND_UP(1000000, 925),
111 DIV_ROUND_UP(1000000, 925));
112 /* At this point conversion must be completed, but anyway... */
113 ret = IIO_VAL_INT;
114 timeout = jiffies + msecs_to_jiffies(1) + 1;
115 while (1) {
116 u32 t;
117
118 t = readl_relaxed(priv->base + EP93XX_ADC_RESULT);
119 if (t & EP93XX_ADC_SDR) {
120 *value = sign_extend32(t, 15);
121 break;
122 }
123
124 if (time_after(jiffies, timeout)) {
125 dev_err(&iiodev->dev, "Conversion timeout\n");
126 ret = -ETIMEDOUT;
127 break;
128 }
129
130 cpu_relax();
131 }
132 mutex_unlock(&priv->lock);
133 return ret;
134
135 case IIO_CHAN_INFO_OFFSET:
136 /* According to datasheet, range is -25000..25000 */
137 *value = 25000;
138 return IIO_VAL_INT;
139
140 case IIO_CHAN_INFO_SCALE:
141 /* Typical supply voltage is 3.3v */
142 *value = (1ULL << 32) * 3300 / 50000;
143 *shift = 32;
144 return IIO_VAL_FRACTIONAL_LOG2;
145 }
146
147 return -EINVAL;
148 }
149
150 static const struct iio_info ep93xx_adc_info = {
151 .read_raw = ep93xx_read_raw,
152 };
153
ep93xx_adc_probe(struct platform_device * pdev)154 static int ep93xx_adc_probe(struct platform_device *pdev)
155 {
156 int ret;
157 struct iio_dev *iiodev;
158 struct ep93xx_adc_priv *priv;
159 struct clk *pclk;
160
161 iiodev = devm_iio_device_alloc(&pdev->dev, sizeof(*priv));
162 if (!iiodev)
163 return -ENOMEM;
164 priv = iio_priv(iiodev);
165
166 priv->base = devm_platform_ioremap_resource(pdev, 0);
167 if (IS_ERR(priv->base))
168 return PTR_ERR(priv->base);
169
170 iiodev->name = dev_name(&pdev->dev);
171 iiodev->modes = INDIO_DIRECT_MODE;
172 iiodev->info = &ep93xx_adc_info;
173 iiodev->num_channels = ARRAY_SIZE(ep93xx_adc_channels);
174 iiodev->channels = ep93xx_adc_channels;
175
176 priv->lastch = -1;
177 mutex_init(&priv->lock);
178
179 platform_set_drvdata(pdev, iiodev);
180
181 priv->clk = devm_clk_get(&pdev->dev, NULL);
182 if (IS_ERR(priv->clk)) {
183 dev_err(&pdev->dev, "Cannot obtain clock\n");
184 return PTR_ERR(priv->clk);
185 }
186
187 pclk = clk_get_parent(priv->clk);
188 if (!pclk) {
189 dev_warn(&pdev->dev, "Cannot obtain parent clock\n");
190 } else {
191 /*
192 * This is actually a place for improvement:
193 * EP93xx ADC supports two clock divisors -- 4 and 16,
194 * resulting in conversion rates 3750 and 925 samples per second
195 * with 500us or 2ms settling time respectively.
196 * One might find this interesting enough to be configurable.
197 */
198 ret = clk_set_rate(priv->clk, clk_get_rate(pclk) / 16);
199 if (ret)
200 dev_warn(&pdev->dev, "Cannot set clock rate\n");
201 /*
202 * We can tolerate rate setting failure because the module should
203 * work in any case.
204 */
205 }
206
207 ret = clk_prepare_enable(priv->clk);
208 if (ret) {
209 dev_err(&pdev->dev, "Cannot enable clock\n");
210 return ret;
211 }
212
213 ret = iio_device_register(iiodev);
214 if (ret)
215 clk_disable_unprepare(priv->clk);
216
217 return ret;
218 }
219
ep93xx_adc_remove(struct platform_device * pdev)220 static int ep93xx_adc_remove(struct platform_device *pdev)
221 {
222 struct iio_dev *iiodev = platform_get_drvdata(pdev);
223 struct ep93xx_adc_priv *priv = iio_priv(iiodev);
224
225 iio_device_unregister(iiodev);
226 clk_disable_unprepare(priv->clk);
227
228 return 0;
229 }
230
231 static const struct of_device_id ep93xx_adc_of_ids[] = {
232 { .compatible = "cirrus,ep9301-adc" },
233 {}
234 };
235 MODULE_DEVICE_TABLE(of, ep93xx_adc_of_ids);
236
237 static struct platform_driver ep93xx_adc_driver = {
238 .driver = {
239 .name = "ep93xx-adc",
240 .of_match_table = ep93xx_adc_of_ids,
241 },
242 .probe = ep93xx_adc_probe,
243 .remove = ep93xx_adc_remove,
244 };
245 module_platform_driver(ep93xx_adc_driver);
246
247 MODULE_AUTHOR("Alexander Sverdlin <alexander.sverdlin@gmail.com>");
248 MODULE_DESCRIPTION("Cirrus Logic EP93XX ADC driver");
249 MODULE_LICENSE("GPL");
250 MODULE_ALIAS("platform:ep93xx-adc");
251
