1// SPDX-License-Identifier: BSD-3-Clause 2/* 3 * Copyright (c) 2022, Eugene Lepshy <fekz115@gmail.com> 4 * Copyright (c) 2022, Gianluca Boiano <morf3089@gmail.com> 5 */ 6/dts-v1/; 7 8#include "msm8953.dtsi" 9#include "pm8953.dtsi" 10#include "pmi8950.dtsi" 11#include <dt-bindings/leds/common.h> 12 13/delete-node/ &adsp_fw_mem; 14/delete-node/ &cont_splash_mem; 15/delete-node/ &qseecom_mem; 16/delete-node/ &wcnss_fw_mem; 17 18/ { 19 model = "Xiaomi Redmi 5 Plus"; 20 compatible = "xiaomi,vince", "qcom,msm8953"; 21 chassis-type = "handset"; 22 qcom,msm-id = <293 0>; 23 qcom,board-id = <0x1000b 0x08>; 24 25 gpio-keys { 26 compatible = "gpio-keys"; 27 28 pinctrl-names = "default"; 29 pinctrl-0 = <&gpio_key_default>; 30 31 key-volume-up { 32 label = "volume_up"; 33 linux,code = <KEY_VOLUMEUP>; 34 gpios = <&tlmm 85 GPIO_ACTIVE_LOW>; 35 }; 36 }; 37 38 reserved-memory { 39 qseecom_mem: qseecom@84a00000 { 40 reg = <0x0 0x84a00000 0x0 0x1900000>; 41 no-map; 42 }; 43 44 cont_splash_mem: cont-splash@90001000 { 45 reg = <0x0 0x90001000 0x0 (1080 * 2160 * 3)>; 46 no-map; 47 }; 48 49 adsp_fw_mem: adsp@8d600000 { 50 reg = <0x0 0x8d600000 0x0 0x1200000>; 51 no-map; 52 }; 53 54 wcnss_fw_mem: wcnss@8e800000 { 55 reg = <0x0 0x8e800000 0x0 0x700000>; 56 no-map; 57 }; 58 59 ramoops@9ff00000 { 60 compatible = "ramoops"; 61 reg = <0x0 0x9ff00000 0x0 0x100000>; 62 record-size = <0x1000>; 63 console-size = <0x80000>; 64 ftrace-size = <0x1000>; 65 pmsg-size = <0x8000>; 66 }; 67 }; 68 69 /* 70 * We bitbang on &i2c_4 because BLSP is protected by TZ as sensors are 71 * normally proxied via ADSP firmware. GPIOs aren't protected. 72 */ 73 i2c-sensors { 74 compatible = "i2c-gpio"; 75 sda-gpios = <&tlmm 14 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; 76 scl-gpios = <&tlmm 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; 77 i2c-gpio,delay-us = <2>; /* ~100 kHz */ 78 #address-cells = <1>; 79 #size-cells = <0>; 80 81 imu@6a { 82 compatible = "st,lsm6dsl"; 83 reg = <0x6a>; 84 vdd-supply = <&pm8953_l10>; 85 vddio-supply = <&pm8953_l6>; 86 mount-matrix = "1", "0", "0", 87 "0", "-1", "0", 88 "0", "0", "1"; 89 }; 90 }; 91 92 vph_pwr: vph-pwr-regulator { 93 compatible = "regulator-fixed"; 94 regulator-name = "vph_pwr"; 95 regulator-always-on; 96 regulator-boot-on; 97 }; 98}; 99 100&hsusb_phy { 101 vdd-supply = <&pm8953_l3>; 102 vdda-pll-supply = <&pm8953_l7>; 103 vdda-phy-dpdm-supply = <&pm8953_l13>; 104 105 status = "okay"; 106}; 107 108&i2c_2 { 109 status = "okay"; 110 111 led-controller@45 { 112 compatible = "awinic,aw2013"; 113 reg = <0x45>; 114 115 vcc-supply = <&pm8953_l10>; 116 117 #address-cells = <1>; 118 #size-cells = <0>; 119 120 led@0 { 121 reg = <0>; 122 led-max-microamp = <5000>; 123 function = LED_FUNCTION_INDICATOR; 124 color = <LED_COLOR_ID_WHITE>; 125 }; 126 }; 127}; 128 129&i2c_3 { 130 status = "okay"; 131 132 touchscreen@20 { 133 reg = <0x20>; 134 compatible = "syna,rmi4-i2c"; 135 interrupts-extended = <&tlmm 65 IRQ_TYPE_EDGE_FALLING>; 136 137 #address-cells = <1>; 138 #size-cells = <0>; 139 140 vdd-supply = <&pm8953_l10>; 141 vio-supply = <&pm8953_l6>; 142 143 pinctrl-names = "init", "suspend"; 144 pinctrl-0 = <&ts_reset_active &ts_int_active>; 145 pinctrl-1 = <&ts_reset_suspend &ts_int_suspend>; 146 syna,reset-delay-ms = <200>; 147 syna,startup-delay-ms = <500>; 148 149 rmi4-f01@1 { 150 reg = <0x01>; 151 syna,nosleep-mode = <1>; 152 }; 153 154 rmi4-f12@12 { 155 reg = <0x12>; 156 syna,rezero-wait-ms = <20>; 157 syna,sensor-type = <1>; 158 touchscreen-x-mm = <68>; 159 touchscreen-y-mm = <122>; 160 }; 161 }; 162}; 163 164&pm8953_resin { 165 linux,code = <KEY_VOLUMEDOWN>; 166 status = "okay"; 167}; 168 169&pmi8950_wled { 170 qcom,current-limit-microamp = <20000>; 171 qcom,ovp-millivolt = <29600>; 172 qcom,num-strings = <2>; 173 qcom,external-pfet; 174 qcom,cabc; 175 176 status = "okay"; 177}; 178 179&rpm_requests { 180 regulators { 181 compatible = "qcom,rpm-pm8953-regulators"; 182 vdd_s1-supply = <&vph_pwr>; 183 vdd_s2-supply = <&vph_pwr>; 184 vdd_s3-supply = <&vph_pwr>; 185 vdd_s4-supply = <&vph_pwr>; 186 vdd_s5-supply = <&vph_pwr>; 187 vdd_s6-supply = <&vph_pwr>; 188 vdd_s7-supply = <&vph_pwr>; 189 vdd_l1-supply = <&pm8953_s3>; 190 vdd_l2_l3-supply = <&pm8953_s3>; 191 vdd_l4_l5_l6_l7_l16_l19-supply = <&pm8953_s4>; 192 vdd_l8_l11_l12_l13_l14_l15-supply = <&vph_pwr>; 193 vdd_l9_l10_l17_l18_l22-supply = <&vph_pwr>; 194 195 pm8953_s1: s1 { 196 regulator-min-microvolt = <870000>; 197 regulator-max-microvolt = <1156000>; 198 }; 199 200 pm8953_s3: s3 { 201 regulator-min-microvolt = <984000>; 202 regulator-max-microvolt = <1224000>; 203 }; 204 205 pm8953_s4: s4 { 206 regulator-min-microvolt = <1900000>; 207 regulator-max-microvolt = <2050000>; 208 }; 209 210 pm8953_l1: l1 { 211 regulator-min-microvolt = <1000000>; 212 regulator-max-microvolt = <1100000>; 213 }; 214 215 pm8953_l2: l2 { 216 regulator-min-microvolt = <1200000>; 217 regulator-max-microvolt = <1225000>; 218 }; 219 220 pm8953_l3: l3 { 221 regulator-min-microvolt = <925000>; 222 regulator-max-microvolt = <925000>; 223 }; 224 225 pm8953_l5: l5 { 226 regulator-min-microvolt = <1800000>; 227 regulator-max-microvolt = <1800000>; 228 }; 229 230 pm8953_l6: l6 { 231 regulator-min-microvolt = <1800000>; 232 regulator-max-microvolt = <1800000>; 233 }; 234 235 pm8953_l7: l7 { 236 regulator-min-microvolt = <1800000>; 237 regulator-max-microvolt = <1900000>; 238 }; 239 240 pm8953_l8: l8 { 241 regulator-min-microvolt = <2900000>; 242 regulator-max-microvolt = <2900000>; 243 }; 244 245 pm8953_l9: l9 { 246 regulator-min-microvolt = <3000000>; 247 regulator-max-microvolt = <3300000>; 248 }; 249 250 pm8953_l10: l10 { 251 regulator-min-microvolt = <2850000>; 252 regulator-max-microvolt = <2850000>; 253 }; 254 255 pm8953_l11: l11 { 256 regulator-min-microvolt = <2950000>; 257 regulator-max-microvolt = <2950000>; 258 }; 259 260 pm8953_l12: l12 { 261 regulator-min-microvolt = <1800000>; 262 regulator-max-microvolt = <2950000>; 263 }; 264 265 pm8953_l13: l13 { 266 regulator-min-microvolt = <3125000>; 267 regulator-max-microvolt = <3125000>; 268 }; 269 270 pm8953_l16: l16 { 271 regulator-min-microvolt = <1800000>; 272 regulator-max-microvolt = <1800000>; 273 }; 274 275 pm8953_l17: l17 { 276 regulator-min-microvolt = <2750000>; 277 regulator-max-microvolt = <2850000>; 278 }; 279 280 pm8953_l19: l19 { 281 regulator-min-microvolt = <1200000>; 282 regulator-max-microvolt = <1380000>; 283 }; 284 285 pm8953_l22: l22 { 286 regulator-min-microvolt = <2800000>; 287 regulator-max-microvolt = <2800000>; 288 }; 289 290 pm8953_l23: l23 { 291 regulator-min-microvolt = <1200000>; 292 regulator-max-microvolt = <1225000>; 293 }; 294 }; 295}; 296 297&sdhc_1 { 298 vmmc-supply = <&pm8953_l8>; 299 vqmmc-supply = <&pm8953_l5>; 300 301 status = "okay"; 302}; 303 304&sdhc_2 { 305 vmmc-supply = <&pm8953_l11>; 306 vqmmc-supply = <&pm8953_l12>; 307 308 pinctrl-names = "default", "sleep"; 309 pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>; 310 pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>; 311 312 status = "okay"; 313}; 314 315&tlmm { 316 gpio-reserved-ranges = <0 4>, <16 4>, <135 4>; 317 318 ts_reset_active: ts-reset-active-state { 319 pins = "gpio64"; 320 function = "gpio"; 321 drive-strength = <8>; 322 bias-pull-up; 323 }; 324 325 ts_reset_suspend: ts-reset-suspend-state { 326 pins = "gpio64"; 327 function = "gpio"; 328 drive-strength = <2>; 329 bias-pull-up; 330 }; 331 332 ts_int_active: ts-int-active-state { 333 pins = "gpio65"; 334 function = "gpio"; 335 drive-strength = <8>; 336 bias-pull-up; 337 }; 338 339 ts_int_suspend: ts-int-suspend-state { 340 pins = "gpio65"; 341 function = "gpio"; 342 drive-strength = <2>; 343 bias-pull-down; 344 }; 345}; 346 347&uart_0 { 348 pinctrl-names = "default"; 349 pinctrl-0 = <&uart_console_active>; 350 351 status = "okay"; 352}; 353 354&usb3 { 355 status = "okay"; 356}; 357 358&usb3_dwc3 { 359 dr_mode = "peripheral"; 360}; 361
