1// SPDX-License-Identifier: GPL-2.0
2/*
3 * Copyright (C) 2017 Centrum Embedded Systems, Jia-Bin Huang <jb@ces.com.tw>
4 * Copyright (C) 2018 Jonathan McDowell <noodles@earth.li>
5 */
6
7/dts-v1/;
8#include "sun8i-h3.dtsi"
9#include "sunxi-common-regulators.dtsi"
10
11#include <dt-bindings/gpio/gpio.h>
12#include <dt-bindings/input/input.h>
13
14/ {
15	model = "MapleBoard MP130";
16	compatible = "mapleboard,mp130", "allwinner,sun8i-h3";
17
18	aliases {
19		ethernet0 = &emac;
20		serial0 = &uart0;
21	};
22
23	chosen {
24		stdout-path = "serial0:115200n8";
25	};
26
27	leds {
28		compatible = "gpio-leds";
29
30		pwr_led {
31			label = "mp130:orange:pwr";
32			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
33			default-state = "on";
34		};
35
36		status_led {
37			label = "mp130:orange:status";
38			gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>;
39		};
40	};
41
42	gpio-keys {
43		compatible = "gpio-keys";
44
45		key-power {
46			label = "power";
47			linux,code = <KEY_POWER>;
48			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; /* PL3 */
49		};
50
51		key-user {
52			label = "user";
53			linux,code = <BTN_0>;
54			gpios = <&r_pio 0 4 GPIO_ACTIVE_LOW>;
55		};
56	};
57};
58
59&codec {
60	allwinner,audio-routing =
61		"Line Out", "LINEOUT",
62		"LINEIN", "Line In";
63	status = "okay";
64};
65
66&ehci1 {
67	status = "okay";
68};
69
70&ehci2 {
71	status = "okay";
72};
73
74&ehci3 {
75	status = "okay";
76};
77
78&emac {
79	phy-handle = <&int_mii_phy>;
80	phy-mode = "mii";
81	allwinner,leds-active-low;
82	status = "okay";
83};
84
85&ir {
86	pinctrl-names = "default";
87	pinctrl-0 = <&r_ir_rx_pin>;
88	status = "okay";
89};
90
91&mmc0 {
92	vmmc-supply = <&reg_vcc3v3>;
93	bus-width = <4>;
94	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
95	status = "okay";
96};
97
98&mmc2 {
99	pinctrl-names = "default";
100	pinctrl-0 = <&mmc2_8bit_pins>;
101	vmmc-supply = <&reg_vcc3v3>;
102	bus-width = <8>;
103	non-removable;
104	cap-mmc-hw-reset;
105	status = "okay";
106};
107
108&ohci1 {
109	status = "okay";
110};
111
112&ohci2 {
113	status = "okay";
114};
115
116&ohci3 {
117	status = "okay";
118};
119
120&uart0 {
121	pinctrl-names = "default";
122	pinctrl-0 = <&uart0_pa_pins>;
123	status = "okay";
124};
125
126&uart1 {
127	pinctrl-names = "default";
128	pinctrl-0 = <&uart1_pins>;
129	status = "disabled";
130};
131
132&uart2 {
133	pinctrl-names = "default";
134	pinctrl-0 = <&uart2_pins>;
135	status = "disabled";
136};
137
138&uart3 {
139	pinctrl-names = "default";
140	pinctrl-0 = <&uart3_pins>;
141	status = "disabled";
142};
143
144&usb_otg {
145	dr_mode = "peripheral";
146	status = "okay";
147};
148
149&usbphy {
150	/* USB VBUS is always on */
151	status = "okay";
152};
153