1// SPDX-License-Identifier: BSD-3-Clause 2/* 3 * SDX55 SoC device tree source 4 * 5 * Copyright (c) 2018, The Linux Foundation. All rights reserved. 6 * Copyright (c) 2020, Linaro Ltd. 7 */ 8 9#include <dt-bindings/clock/qcom,gcc-sdx55.h> 10#include <dt-bindings/clock/qcom,rpmh.h> 11#include <dt-bindings/gpio/gpio.h> 12#include <dt-bindings/interconnect/qcom,sdx55.h> 13#include <dt-bindings/interrupt-controller/arm-gic.h> 14#include <dt-bindings/power/qcom-rpmpd.h> 15#include <dt-bindings/soc/qcom,rpmh-rsc.h> 16 17/ { 18 #address-cells = <1>; 19 #size-cells = <1>; 20 qcom,msm-id = <357 0x10000>, <368 0x10000>, <418 0x10000>; 21 interrupt-parent = <&intc>; 22 23 memory { 24 device_type = "memory"; 25 reg = <0 0>; 26 }; 27 28 clocks { 29 xo_board: xo-board { 30 compatible = "fixed-clock"; 31 #clock-cells = <0>; 32 clock-frequency = <38400000>; 33 clock-output-names = "xo_board"; 34 }; 35 36 sleep_clk: sleep-clk { 37 compatible = "fixed-clock"; 38 #clock-cells = <0>; 39 clock-frequency = <32000>; 40 }; 41 42 nand_clk_dummy: nand-clk-dummy { 43 compatible = "fixed-clock"; 44 #clock-cells = <0>; 45 clock-frequency = <32000>; 46 }; 47 }; 48 49 cpus { 50 #address-cells = <1>; 51 #size-cells = <0>; 52 53 cpu0: cpu@0 { 54 device_type = "cpu"; 55 compatible = "arm,cortex-a7"; 56 reg = <0x0>; 57 enable-method = "psci"; 58 clocks = <&apcs>; 59 power-domains = <&rpmhpd SDX55_CX>; 60 power-domain-names = "rpmhpd"; 61 operating-points-v2 = <&cpu_opp_table>; 62 }; 63 }; 64 65 cpu_opp_table: cpu-opp-table { 66 compatible = "operating-points-v2"; 67 opp-shared; 68 69 opp-345600000 { 70 opp-hz = /bits/ 64 <345600000>; 71 required-opps = <&rpmhpd_opp_low_svs>; 72 }; 73 74 opp-576000000 { 75 opp-hz = /bits/ 64 <576000000>; 76 required-opps = <&rpmhpd_opp_svs>; 77 }; 78 79 opp-1094400000 { 80 opp-hz = /bits/ 64 <1094400000>; 81 required-opps = <&rpmhpd_opp_nom>; 82 }; 83 84 opp-1555200000 { 85 opp-hz = /bits/ 64 <1555200000>; 86 required-opps = <&rpmhpd_opp_turbo>; 87 }; 88 }; 89 90 firmware { 91 scm { 92 compatible = "qcom,scm-sdx55", "qcom,scm"; 93 }; 94 }; 95 96 psci { 97 compatible = "arm,psci-1.0"; 98 method = "smc"; 99 }; 100 101 reserved-memory { 102 #address-cells = <1>; 103 #size-cells = <1>; 104 ranges; 105 106 hyp_mem: memory@8fc00000 { 107 no-map; 108 reg = <0x8fc00000 0x80000>; 109 }; 110 111 ac_db_mem: memory@8fc80000 { 112 no-map; 113 reg = <0x8fc80000 0x40000>; 114 }; 115 116 secdata_mem: memory@8fcfd000 { 117 no-map; 118 reg = <0x8fcfd000 0x1000>; 119 }; 120 121 sbl_mem: memory@8fd00000 { 122 no-map; 123 reg = <0x8fd00000 0x100000>; 124 }; 125 126 aop_image: memory@8fe00000 { 127 no-map; 128 reg = <0x8fe00000 0x20000>; 129 }; 130 131 aop_cmd_db: memory@8fe20000 { 132 compatible = "qcom,cmd-db"; 133 reg = <0x8fe20000 0x20000>; 134 no-map; 135 }; 136 137 smem_mem: memory@8fe40000 { 138 no-map; 139 reg = <0x8fe40000 0xc0000>; 140 }; 141 142 tz_mem: memory@8ff00000 { 143 no-map; 144 reg = <0x8ff00000 0x100000>; 145 }; 146 147 tz_apps_mem: memory@90000000 { 148 no-map; 149 reg = <0x90000000 0x500000>; 150 }; 151 }; 152 153 smem { 154 compatible = "qcom,smem"; 155 memory-region = <&smem_mem>; 156 hwlocks = <&tcsr_mutex 3>; 157 }; 158 159 smp2p-mpss { 160 compatible = "qcom,smp2p"; 161 qcom,smem = <435>, <428>; 162 interrupts = <GIC_SPI 113 IRQ_TYPE_EDGE_RISING>; 163 mboxes = <&apcs 14>; 164 qcom,local-pid = <0>; 165 qcom,remote-pid = <1>; 166 167 modem_smp2p_out: master-kernel { 168 qcom,entry-name = "master-kernel"; 169 #qcom,smem-state-cells = <1>; 170 }; 171 172 modem_smp2p_in: slave-kernel { 173 qcom,entry-name = "slave-kernel"; 174 interrupt-controller; 175 #interrupt-cells = <2>; 176 }; 177 178 ipa_smp2p_out: ipa-ap-to-modem { 179 qcom,entry-name = "ipa"; 180 #qcom,smem-state-cells = <1>; 181 }; 182 183 ipa_smp2p_in: ipa-modem-to-ap { 184 qcom,entry-name = "ipa"; 185 interrupt-controller; 186 #interrupt-cells = <2>; 187 }; 188 }; 189 190 soc: soc { 191 #address-cells = <1>; 192 #size-cells = <1>; 193 ranges; 194 compatible = "simple-bus"; 195 196 gcc: clock-controller@100000 { 197 compatible = "qcom,gcc-sdx55"; 198 reg = <0x100000 0x1f0000>; 199 #clock-cells = <1>; 200 #reset-cells = <1>; 201 #power-domain-cells = <1>; 202 clock-names = "bi_tcxo", "sleep_clk"; 203 clocks = <&rpmhcc RPMH_CXO_CLK>, <&sleep_clk>; 204 }; 205 206 blsp1_uart3: serial@831000 { 207 compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; 208 reg = <0x00831000 0x200>; 209 interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; 210 clocks = <&gcc 30>, 211 <&gcc 9>; 212 clock-names = "core", "iface"; 213 status = "disabled"; 214 }; 215 216 usb_hsphy: phy@ff4000 { 217 compatible = "qcom,usb-snps-hs-7nm-phy"; 218 reg = <0x00ff4000 0x114>; 219 status = "disabled"; 220 #phy-cells = <0>; 221 222 clocks = <&rpmhcc RPMH_CXO_CLK>; 223 clock-names = "ref"; 224 225 resets = <&gcc GCC_QUSB2PHY_BCR>; 226 }; 227 228 usb_qmpphy: phy@ff6000 { 229 compatible = "qcom,sdx55-qmp-usb3-uni-phy"; 230 reg = <0x00ff6000 0x1c0>; 231 status = "disabled"; 232 #address-cells = <1>; 233 #size-cells = <1>; 234 ranges; 235 236 clocks = <&gcc GCC_USB3_PHY_AUX_CLK>, 237 <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>, 238 <&gcc GCC_USB3_PRIM_CLKREF_CLK>; 239 clock-names = "aux", "cfg_ahb", "ref"; 240 241 resets = <&gcc GCC_USB3PHY_PHY_BCR>, 242 <&gcc GCC_USB3_PHY_BCR>; 243 reset-names = "phy", "common"; 244 245 usb_ssphy: phy@ff6200 { 246 reg = <0x00ff6200 0x170>, 247 <0x00ff6400 0x200>, 248 <0x00ff6800 0x800>; 249 #phy-cells = <0>; 250 #clock-cells = <0>; 251 clocks = <&gcc GCC_USB3_PHY_PIPE_CLK>; 252 clock-names = "pipe0"; 253 clock-output-names = "usb3_uni_phy_pipe_clk_src"; 254 }; 255 }; 256 257 mc_virt: interconnect@1100000 { 258 compatible = "qcom,sdx55-mc-virt"; 259 reg = <0x01100000 0x400000>; 260 #interconnect-cells = <1>; 261 qcom,bcm-voters = <&apps_bcm_voter>; 262 }; 263 264 mem_noc: interconnect@9680000 { 265 compatible = "qcom,sdx55-mem-noc"; 266 reg = <0x09680000 0x40000>; 267 #interconnect-cells = <1>; 268 qcom,bcm-voters = <&apps_bcm_voter>; 269 }; 270 271 system_noc: interconnect@162c000 { 272 compatible = "qcom,sdx55-system-noc"; 273 reg = <0x0162c000 0x31200>; 274 #interconnect-cells = <1>; 275 qcom,bcm-voters = <&apps_bcm_voter>; 276 }; 277 278 qpic_bam: dma-controller@1b04000 { 279 compatible = "qcom,bam-v1.7.0"; 280 reg = <0x01b04000 0x1c000>; 281 interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>; 282 clocks = <&rpmhcc RPMH_QPIC_CLK>; 283 clock-names = "bam_clk"; 284 #dma-cells = <1>; 285 qcom,ee = <0>; 286 qcom,controlled-remotely; 287 status = "disabled"; 288 }; 289 290 qpic_nand: nand-controller@1b30000 { 291 compatible = "qcom,sdx55-nand"; 292 reg = <0x01b30000 0x10000>; 293 #address-cells = <1>; 294 #size-cells = <0>; 295 clocks = <&rpmhcc RPMH_QPIC_CLK>, 296 <&nand_clk_dummy>; 297 clock-names = "core", "aon"; 298 299 dmas = <&qpic_bam 0>, 300 <&qpic_bam 1>, 301 <&qpic_bam 2>; 302 dma-names = "tx", "rx", "cmd"; 303 status = "disabled"; 304 }; 305 306 pcie0_phy: phy@1c07000 { 307 compatible = "qcom,sdx55-qmp-pcie-phy"; 308 reg = <0x01c07000 0x1c4>; 309 #address-cells = <1>; 310 #size-cells = <1>; 311 ranges; 312 clocks = <&gcc GCC_PCIE_AUX_PHY_CLK_SRC>, 313 <&gcc GCC_PCIE_CFG_AHB_CLK>, 314 <&gcc GCC_PCIE_0_CLKREF_CLK>, 315 <&gcc GCC_PCIE_RCHNG_PHY_CLK>; 316 clock-names = "aux", "cfg_ahb", "ref", "refgen"; 317 318 resets = <&gcc GCC_PCIE_PHY_BCR>; 319 reset-names = "phy"; 320 321 assigned-clocks = <&gcc GCC_PCIE_RCHNG_PHY_CLK>; 322 assigned-clock-rates = <100000000>; 323 324 status = "disabled"; 325 326 pcie0_lane: lanes@1c06000 { 327 reg = <0x01c06000 0x104>, /* tx0 */ 328 <0x01c06200 0x328>, /* rx0 */ 329 <0x01c07200 0x1e8>, /* pcs */ 330 <0x01c06800 0x104>, /* tx1 */ 331 <0x01c06a00 0x328>, /* rx1 */ 332 <0x01c07600 0x800>; /* pcs_misc */ 333 clocks = <&gcc GCC_PCIE_PIPE_CLK>; 334 clock-names = "pipe0"; 335 336 #phy-cells = <0>; 337 clock-output-names = "pcie_pipe_clk"; 338 }; 339 }; 340 341 ipa: ipa@1e40000 { 342 compatible = "qcom,sdx55-ipa"; 343 344 iommus = <&apps_smmu 0x5e0 0x0>, 345 <&apps_smmu 0x5e2 0x0>; 346 reg = <0x1e40000 0x7000>, 347 <0x1e50000 0x4b20>, 348 <0x1e04000 0x2c000>; 349 reg-names = "ipa-reg", 350 "ipa-shared", 351 "gsi"; 352 353 interrupts-extended = <&intc GIC_SPI 241 IRQ_TYPE_EDGE_RISING>, 354 <&intc GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>, 355 <&ipa_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, 356 <&ipa_smp2p_in 1 IRQ_TYPE_EDGE_RISING>; 357 interrupt-names = "ipa", 358 "gsi", 359 "ipa-clock-query", 360 "ipa-setup-ready"; 361 362 clocks = <&rpmhcc RPMH_IPA_CLK>; 363 clock-names = "core"; 364 365 interconnects = <&system_noc MASTER_IPA &mc_virt SLAVE_EBI_CH0>, 366 <&system_noc MASTER_IPA &system_noc SLAVE_OCIMEM>, 367 <&mem_noc MASTER_AMPSS_M0 &system_noc SLAVE_IPA_CFG>; 368 interconnect-names = "memory", 369 "imem", 370 "config"; 371 372 qcom,smem-states = <&ipa_smp2p_out 0>, 373 <&ipa_smp2p_out 1>; 374 qcom,smem-state-names = "ipa-clock-enabled-valid", 375 "ipa-clock-enabled"; 376 377 status = "disabled"; 378 }; 379 380 tcsr_mutex: hwlock@1f40000 { 381 compatible = "qcom,tcsr-mutex"; 382 reg = <0x01f40000 0x40000>; 383 #hwlock-cells = <1>; 384 }; 385 386 tcsr: syscon@1fcb000 { 387 compatible = "syscon"; 388 reg = <0x01fc0000 0x1000>; 389 }; 390 391 sdhc_1: mmc@8804000 { 392 compatible = "qcom,sdx55-sdhci", "qcom,sdhci-msm-v5"; 393 reg = <0x08804000 0x1000>; 394 interrupts = <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>, 395 <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>; 396 interrupt-names = "hc_irq", "pwr_irq"; 397 clocks = <&gcc GCC_SDCC1_AHB_CLK>, 398 <&gcc GCC_SDCC1_APPS_CLK>; 399 clock-names = "iface", "core"; 400 status = "disabled"; 401 }; 402 403 pcie_ep: pcie-ep@40000000 { 404 compatible = "qcom,sdx55-pcie-ep"; 405 reg = <0x01c00000 0x3000>, 406 <0x40000000 0xf1d>, 407 <0x40000f20 0xc8>, 408 <0x40001000 0x1000>, 409 <0x40200000 0x100000>, 410 <0x01c03000 0x3000>; 411 reg-names = "parf", "dbi", "elbi", "atu", "addr_space", 412 "mmio"; 413 414 qcom,perst-regs = <&tcsr 0xb258 0xb270>; 415 416 clocks = <&gcc GCC_PCIE_AUX_CLK>, 417 <&gcc GCC_PCIE_CFG_AHB_CLK>, 418 <&gcc GCC_PCIE_MSTR_AXI_CLK>, 419 <&gcc GCC_PCIE_SLV_AXI_CLK>, 420 <&gcc GCC_PCIE_SLV_Q2A_AXI_CLK>, 421 <&gcc GCC_PCIE_SLEEP_CLK>, 422 <&gcc GCC_PCIE_0_CLKREF_CLK>; 423 clock-names = "aux", "cfg", "bus_master", "bus_slave", 424 "slave_q2a", "sleep", "ref"; 425 426 interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>, 427 <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>; 428 interrupt-names = "global", "doorbell"; 429 reset-gpios = <&tlmm 57 GPIO_ACTIVE_LOW>; 430 wake-gpios = <&tlmm 53 GPIO_ACTIVE_LOW>; 431 resets = <&gcc GCC_PCIE_BCR>; 432 reset-names = "core"; 433 power-domains = <&gcc PCIE_GDSC>; 434 phys = <&pcie0_lane>; 435 phy-names = "pciephy"; 436 max-link-speed = <3>; 437 num-lanes = <2>; 438 439 status = "disabled"; 440 }; 441 442 remoteproc_mpss: remoteproc@4080000 { 443 compatible = "qcom,sdx55-mpss-pas"; 444 reg = <0x04080000 0x4040>; 445 446 interrupts-extended = <&intc GIC_SPI 250 IRQ_TYPE_EDGE_RISING>, 447 <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, 448 <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, 449 <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, 450 <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>, 451 <&modem_smp2p_in 7 IRQ_TYPE_EDGE_RISING>; 452 interrupt-names = "wdog", "fatal", "ready", "handover", 453 "stop-ack", "shutdown-ack"; 454 455 clocks = <&rpmhcc RPMH_CXO_CLK>; 456 clock-names = "xo"; 457 458 power-domains = <&rpmhpd SDX55_CX>, 459 <&rpmhpd SDX55_MSS>; 460 power-domain-names = "cx", "mss"; 461 462 qcom,smem-states = <&modem_smp2p_out 0>; 463 qcom,smem-state-names = "stop"; 464 465 status = "disabled"; 466 467 glink-edge { 468 interrupts = <GIC_SPI 114 IRQ_TYPE_EDGE_RISING>; 469 label = "mpss"; 470 qcom,remote-pid = <1>; 471 mboxes = <&apcs 15>; 472 }; 473 }; 474 475 usb: usb@a6f8800 { 476 compatible = "qcom,sdx55-dwc3", "qcom,dwc3"; 477 reg = <0x0a6f8800 0x400>; 478 status = "disabled"; 479 #address-cells = <1>; 480 #size-cells = <1>; 481 ranges; 482 483 clocks = <&gcc GCC_USB30_SLV_AHB_CLK>, 484 <&gcc GCC_USB30_MASTER_CLK>, 485 <&gcc GCC_USB30_MSTR_AXI_CLK>, 486 <&gcc GCC_USB30_SLEEP_CLK>, 487 <&gcc GCC_USB30_MOCK_UTMI_CLK>; 488 clock-names = "cfg_noc", 489 "core", 490 "iface", 491 "sleep", 492 "mock_utmi"; 493 494 assigned-clocks = <&gcc GCC_USB30_MOCK_UTMI_CLK>, 495 <&gcc GCC_USB30_MASTER_CLK>; 496 assigned-clock-rates = <19200000>, <200000000>; 497 498 interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>, 499 <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>, 500 <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>, 501 <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>; 502 interrupt-names = "hs_phy_irq", "ss_phy_irq", 503 "dm_hs_phy_irq", "dp_hs_phy_irq"; 504 505 power-domains = <&gcc USB30_GDSC>; 506 507 resets = <&gcc GCC_USB30_BCR>; 508 509 usb_dwc3: dwc3@a600000 { 510 compatible = "snps,dwc3"; 511 reg = <0x0a600000 0xcd00>; 512 interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; 513 iommus = <&apps_smmu 0x1a0 0x0>; 514 snps,dis_u2_susphy_quirk; 515 snps,dis_enblslpm_quirk; 516 phys = <&usb_hsphy>, <&usb_ssphy>; 517 phy-names = "usb2-phy", "usb3-phy"; 518 }; 519 }; 520 521 pdc: interrupt-controller@b210000 { 522 compatible = "qcom,sdx55-pdc", "qcom,pdc"; 523 reg = <0x0b210000 0x30000>; 524 qcom,pdc-ranges = <0 179 52>; 525 #interrupt-cells = <3>; 526 interrupt-parent = <&intc>; 527 interrupt-controller; 528 }; 529 530 restart@c264000 { 531 compatible = "qcom,pshold"; 532 reg = <0x0c264000 0x1000>; 533 }; 534 535 spmi_bus: spmi@c440000 { 536 compatible = "qcom,spmi-pmic-arb"; 537 reg = <0x0c440000 0x0000d00>, 538 <0x0c600000 0x2000000>, 539 <0x0e600000 0x0100000>, 540 <0x0e700000 0x00a0000>, 541 <0x0c40a000 0x0000700>; 542 reg-names = "core", "chnls", "obsrvr", "intr", "cnfg"; 543 interrupt-names = "periph_irq"; 544 interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>; 545 qcom,ee = <0>; 546 qcom,channel = <0>; 547 #address-cells = <2>; 548 #size-cells = <0>; 549 interrupt-controller; 550 #interrupt-cells = <4>; 551 cell-index = <0>; 552 }; 553 554 tlmm: pinctrl@f100000 { 555 compatible = "qcom,sdx55-pinctrl"; 556 reg = <0xf100000 0x300000>; 557 interrupts = <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>; 558 gpio-controller; 559 #gpio-cells = <2>; 560 interrupt-controller; 561 #interrupt-cells = <2>; 562 }; 563 564 sram@1468f000 { 565 compatible = "qcom,sdx55-imem", "syscon", "simple-mfd"; 566 reg = <0x1468f000 0x1000>; 567 568 #address-cells = <1>; 569 #size-cells = <1>; 570 571 ranges = <0x0 0x1468f000 0x1000>; 572 573 pil-reloc@94c { 574 compatible = "qcom,pil-reloc-info"; 575 reg = <0x94c 0x200>; 576 }; 577 }; 578 579 apps_smmu: iommu@15000000 { 580 compatible = "qcom,sdx55-smmu-500", "arm,mmu-500"; 581 reg = <0x15000000 0x20000>; 582 #iommu-cells = <2>; 583 #global-interrupts = <1>; 584 interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>, 585 <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>, 586 <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>, 587 <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, 588 <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>, 589 <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>, 590 <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>, 591 <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>, 592 <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>, 593 <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, 594 <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>, 595 <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>, 596 <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>, 597 <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>, 598 <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>, 599 <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>, 600 <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; 601 }; 602 603 intc: interrupt-controller@17800000 { 604 compatible = "qcom,msm-qgic2"; 605 interrupt-controller; 606 interrupt-parent = <&intc>; 607 #interrupt-cells = <3>; 608 reg = <0x17800000 0x1000>, 609 <0x17802000 0x1000>; 610 }; 611 612 a7pll: clock@17808000 { 613 compatible = "qcom,sdx55-a7pll"; 614 reg = <0x17808000 0x1000>; 615 clocks = <&rpmhcc RPMH_CXO_CLK>; 616 clock-names = "bi_tcxo"; 617 #clock-cells = <0>; 618 }; 619 620 apcs: mailbox@17810000 { 621 compatible = "qcom,sdx55-apcs-gcc", "syscon"; 622 reg = <0x17810000 0x2000>; 623 #mbox-cells = <1>; 624 clocks = <&rpmhcc RPMH_CXO_CLK>, <&a7pll>, <&gcc GPLL0>; 625 clock-names = "ref", "pll", "aux"; 626 #clock-cells = <0>; 627 }; 628 629 watchdog@17817000 { 630 compatible = "qcom,apss-wdt-sdx55", "qcom,kpss-wdt"; 631 reg = <0x17817000 0x1000>; 632 clocks = <&sleep_clk>; 633 }; 634 635 timer@17820000 { 636 #address-cells = <1>; 637 #size-cells = <1>; 638 ranges; 639 compatible = "arm,armv7-timer-mem"; 640 reg = <0x17820000 0x1000>; 641 clock-frequency = <19200000>; 642 643 frame@17821000 { 644 frame-number = <0>; 645 interrupts = <GIC_SPI 7 0x4>, 646 <GIC_SPI 6 0x4>; 647 reg = <0x17821000 0x1000>, 648 <0x17822000 0x1000>; 649 }; 650 651 frame@17823000 { 652 frame-number = <1>; 653 interrupts = <GIC_SPI 8 0x4>; 654 reg = <0x17823000 0x1000>; 655 status = "disabled"; 656 }; 657 658 frame@17824000 { 659 frame-number = <2>; 660 interrupts = <GIC_SPI 9 0x4>; 661 reg = <0x17824000 0x1000>; 662 status = "disabled"; 663 }; 664 665 frame@17825000 { 666 frame-number = <3>; 667 interrupts = <GIC_SPI 10 0x4>; 668 reg = <0x17825000 0x1000>; 669 status = "disabled"; 670 }; 671 672 frame@17826000 { 673 frame-number = <4>; 674 interrupts = <GIC_SPI 11 0x4>; 675 reg = <0x17826000 0x1000>; 676 status = "disabled"; 677 }; 678 679 frame@17827000 { 680 frame-number = <5>; 681 interrupts = <GIC_SPI 12 0x4>; 682 reg = <0x17827000 0x1000>; 683 status = "disabled"; 684 }; 685 686 frame@17828000 { 687 frame-number = <6>; 688 interrupts = <GIC_SPI 13 0x4>; 689 reg = <0x17828000 0x1000>; 690 status = "disabled"; 691 }; 692 693 frame@17829000 { 694 frame-number = <7>; 695 interrupts = <GIC_SPI 14 0x4>; 696 reg = <0x17829000 0x1000>; 697 status = "disabled"; 698 }; 699 }; 700 701 apps_rsc: rsc@17840000 { 702 compatible = "qcom,rpmh-rsc"; 703 reg = <0x17830000 0x10000>, <0x17840000 0x10000>; 704 reg-names = "drv-0", "drv-1"; 705 interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>, 706 <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; 707 qcom,tcs-offset = <0xd00>; 708 qcom,drv-id = <1>; 709 qcom,tcs-config = <ACTIVE_TCS 2>, <SLEEP_TCS 2>, 710 <WAKE_TCS 2>, <CONTROL_TCS 1>; 711 712 rpmhcc: clock-controller { 713 compatible = "qcom,sdx55-rpmh-clk"; 714 #clock-cells = <1>; 715 clock-names = "xo"; 716 clocks = <&xo_board>; 717 }; 718 719 rpmhpd: power-controller { 720 compatible = "qcom,sdx55-rpmhpd"; 721 #power-domain-cells = <1>; 722 operating-points-v2 = <&rpmhpd_opp_table>; 723 724 rpmhpd_opp_table: opp-table { 725 compatible = "operating-points-v2"; 726 727 rpmhpd_opp_ret: opp1 { 728 opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>; 729 }; 730 731 rpmhpd_opp_min_svs: opp2 { 732 opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>; 733 }; 734 735 rpmhpd_opp_low_svs: opp3 { 736 opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>; 737 }; 738 739 rpmhpd_opp_svs: opp4 { 740 opp-level = <RPMH_REGULATOR_LEVEL_SVS>; 741 }; 742 743 rpmhpd_opp_svs_l1: opp5 { 744 opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>; 745 }; 746 747 rpmhpd_opp_nom: opp6 { 748 opp-level = <RPMH_REGULATOR_LEVEL_NOM>; 749 }; 750 751 rpmhpd_opp_nom_l1: opp7 { 752 opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>; 753 }; 754 755 rpmhpd_opp_nom_l2: opp8 { 756 opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>; 757 }; 758 759 rpmhpd_opp_turbo: opp9 { 760 opp-level = <RPMH_REGULATOR_LEVEL_TURBO>; 761 }; 762 763 rpmhpd_opp_turbo_l1: opp10 { 764 opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>; 765 }; 766 }; 767 }; 768 769 apps_bcm_voter: bcm-voter { 770 compatible = "qcom,bcm-voter"; 771 }; 772 }; 773 }; 774 775 timer { 776 compatible = "arm,armv7-timer"; 777 interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, 778 <GIC_PPI 12 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, 779 <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, 780 <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; 781 clock-frequency = <19200000>; 782 }; 783}; 784
