1// SPDX-License-Identifier: GPL-2.0
2/dts-v1/;
3#include "bcm2837.dtsi"
4#include "bcm2836-rpi.dtsi"
5#include "bcm283x-rpi-lan7515.dtsi"
6#include "bcm283x-rpi-usb-host.dtsi"
7
8/ {
9	compatible = "raspberrypi,3-model-b-plus", "brcm,bcm2837";
10	model = "Raspberry Pi 3 Model B+";
11
12	chosen {
13		/* 8250 auxiliary UART instead of pl011 */
14		stdout-path = "serial1:115200n8";
15	};
16
17	memory@0 {
18		device_type = "memory";
19		reg = <0 0x40000000>;
20	};
21
22	leds {
23		act {
24			gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
25		};
26
27		pwr {
28			label = "PWR";
29			gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
30		};
31	};
32
33	wifi_pwrseq: wifi-pwrseq {
34		compatible = "mmc-pwrseq-simple";
35		reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
36	};
37};
38
39&firmware {
40	expgpio: gpio {
41		compatible = "raspberrypi,firmware-gpio";
42		gpio-controller;
43		#gpio-cells = <2>;
44		gpio-line-names = "BT_ON",
45				  "WL_ON",
46				  "STATUS_LED_R",
47				  "LAN_RUN",
48				  "",
49				  "CAM_GPIO0",
50				  "CAM_GPIO1",
51				  "";
52		status = "okay";
53	};
54};
55
56&gpio {
57	/*
58	 * Taken from rpi_SCH_3bplus_1p0_reduced.pdf and
59	 * the official GPU firmware DT blob.
60	 *
61	 * Legend:
62	 * "NC" = not connected (no rail from the SoC)
63	 * "FOO" = GPIO line named "FOO" on the schematic
64	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
65	 */
66	gpio-line-names = "ID_SDA",
67			  "ID_SCL",
68			  "SDA1",
69			  "SCL1",
70			  "GPIO_GCLK",
71			  "GPIO5",
72			  "GPIO6",
73			  "SPI_CE1_N",
74			  "SPI_CE0_N",
75			  "SPI_MISO",
76			  "SPI_MOSI",
77			  "SPI_SCLK",
78			  "GPIO12",
79			  "GPIO13",
80			  /* Serial port */
81			  "TXD1",
82			  "RXD1",
83			  "GPIO16",
84			  "GPIO17",
85			  "GPIO18",
86			  "GPIO19",
87			  "GPIO20",
88			  "GPIO21",
89			  "GPIO22",
90			  "GPIO23",
91			  "GPIO24",
92			  "GPIO25",
93			  "GPIO26",
94			  "GPIO27",
95			  "HDMI_HPD_N",
96			  "STATUS_LED_G",
97			  /* Used by BT module */
98			  "CTS0",
99			  "RTS0",
100			  "TXD0",
101			  "RXD0",
102			  /* Used by Wifi */
103			  "SD1_CLK",
104			  "SD1_CMD",
105			  "SD1_DATA0",
106			  "SD1_DATA1",
107			  "SD1_DATA2",
108			  "SD1_DATA3",
109			  "PWM0_OUT",
110			  "PWM1_OUT",
111			  "ETHCLK",
112			  "WIFI_CLK",
113			  "SDA0",
114			  "SCL0",
115			  "SMPS_SCL",
116			  "SMPS_SDA",
117			  /* Used by SD Card */
118			  "SD_CLK_R",
119			  "SD_CMD_R",
120			  "SD_DATA0_R",
121			  "SD_DATA1_R",
122			  "SD_DATA2_R",
123			  "SD_DATA3_R";
124};
125
126&hdmi {
127	hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
128	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
129	status = "okay";
130};
131
132&pwm {
133	pinctrl-names = "default";
134	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
135	status = "okay";
136};
137
138/* SDHCI is used to control the SDIO for wireless */
139&sdhci {
140	#address-cells = <1>;
141	#size-cells = <0>;
142	pinctrl-names = "default";
143	pinctrl-0 = <&emmc_gpio34>;
144	status = "okay";
145	bus-width = <4>;
146	non-removable;
147	mmc-pwrseq = <&wifi_pwrseq>;
148
149	brcmf: wifi@1 {
150		reg = <1>;
151		compatible = "brcm,bcm4329-fmac";
152	};
153};
154
155/* SDHOST is used to drive the SD card */
156&sdhost {
157	pinctrl-names = "default";
158	pinctrl-0 = <&sdhost_gpio48>;
159	status = "okay";
160	bus-width = <4>;
161};
162
163/* uart0 communicates with the BT module */
164&uart0 {
165	pinctrl-names = "default";
166	pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>;
167	status = "okay";
168
169	bluetooth {
170		compatible = "brcm,bcm43438-bt";
171		max-speed = <2000000>;
172		shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
173	};
174};
175
176/* uart1 is mapped to the pin header */
177&uart1 {
178	pinctrl-names = "default";
179	pinctrl-0 = <&uart1_gpio14>;
180	status = "okay";
181};
182