1// SPDX-License-Identifier: GPL-2.0
2/*
3 * Device Tree Source for the Lager board
4 *
5 * Copyright (C) 2013-2014 Renesas Solutions Corp.
6 * Copyright (C) 2014 Cogent Embedded, Inc.
7 * Copyright (C) 2015-2016 Renesas Electronics Corporation
8 */
9
10/*
11 * SSI-AK4643
12 *
13 * SW1: 1: AK4643
14 *      2: CN22
15 *      3: ADV7511
16 *
17 * This command is required when Playback/Capture
18 *
19 *	amixer set "LINEOUT Mixer DACL" on
20 *	amixer set "DVC Out" 100%
21 *	amixer set "DVC In" 100%
22 *
23 * You can use Mute
24 *
25 *	amixer set "DVC Out Mute" on
26 *	amixer set "DVC In Mute" on
27 *
28 * You can use Volume Ramp
29 *
30 *	amixer set "DVC Out Ramp Up Rate"   "0.125 dB/64 steps"
31 *	amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
32 *	amixer set "DVC Out Ramp" on
33 *	aplay xxx.wav &
34 *	amixer set "DVC Out"  80%  // Volume Down
35 *	amixer set "DVC Out" 100%  // Volume Up
36 */
37
38/dts-v1/;
39#include "r8a7790.dtsi"
40#include <dt-bindings/gpio/gpio.h>
41#include <dt-bindings/input/input.h>
42
43/ {
44	model = "Lager";
45	compatible = "renesas,lager", "renesas,r8a7790";
46
47	aliases {
48		serial0 = &scif0;
49		serial1 = &scifa1;
50		i2c8 = &gpioi2c1;
51		i2c9 = &gpioi2c2;
52		i2c10 = &i2cexio0;
53		i2c11 = &i2cexio1;
54		i2c12 = &i2chdmi;
55		i2c13 = &i2cpwr;
56	};
57
58	chosen {
59		bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
60		stdout-path = "serial0:115200n8";
61	};
62
63	memory@40000000 {
64		device_type = "memory";
65		reg = <0 0x40000000 0 0x40000000>;
66	};
67
68	memory@140000000 {
69		device_type = "memory";
70		reg = <1 0x40000000 0 0xc0000000>;
71	};
72
73	lbsc {
74		#address-cells = <1>;
75		#size-cells = <1>;
76	};
77
78	keyboard {
79		compatible = "gpio-keys";
80
81		one {
82			linux,code = <KEY_1>;
83			label = "SW2-1";
84			wakeup-source;
85			debounce-interval = <20>;
86			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
87		};
88		two {
89			linux,code = <KEY_2>;
90			label = "SW2-2";
91			wakeup-source;
92			debounce-interval = <20>;
93			gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
94		};
95		three {
96			linux,code = <KEY_3>;
97			label = "SW2-3";
98			wakeup-source;
99			debounce-interval = <20>;
100			gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
101		};
102		four {
103			linux,code = <KEY_4>;
104			label = "SW2-4";
105			wakeup-source;
106			debounce-interval = <20>;
107			gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
108		};
109	};
110
111	leds {
112		compatible = "gpio-leds";
113		led6 {
114			gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
115		};
116		led7 {
117			gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;
118		};
119		led8 {
120			gpios = <&gpio5 17 GPIO_ACTIVE_HIGH>;
121		};
122	};
123
124	fixedregulator3v3: regulator-3v3 {
125		compatible = "regulator-fixed";
126		regulator-name = "fixed-3.3V";
127		regulator-min-microvolt = <3300000>;
128		regulator-max-microvolt = <3300000>;
129		regulator-boot-on;
130		regulator-always-on;
131	};
132
133	vcc_sdhi0: regulator-vcc-sdhi0 {
134		compatible = "regulator-fixed";
135
136		regulator-name = "SDHI0 Vcc";
137		regulator-min-microvolt = <3300000>;
138		regulator-max-microvolt = <3300000>;
139
140		gpio = <&gpio5 24 GPIO_ACTIVE_HIGH>;
141		enable-active-high;
142	};
143
144	vccq_sdhi0: regulator-vccq-sdhi0 {
145		compatible = "regulator-gpio";
146
147		regulator-name = "SDHI0 VccQ";
148		regulator-min-microvolt = <1800000>;
149		regulator-max-microvolt = <3300000>;
150
151		gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
152		gpios-states = <1>;
153		states = <3300000 1
154			  1800000 0>;
155	};
156
157	vcc_sdhi2: regulator-vcc-sdhi2 {
158		compatible = "regulator-fixed";
159
160		regulator-name = "SDHI2 Vcc";
161		regulator-min-microvolt = <3300000>;
162		regulator-max-microvolt = <3300000>;
163
164		gpio = <&gpio5 25 GPIO_ACTIVE_HIGH>;
165		enable-active-high;
166	};
167
168	vccq_sdhi2: regulator-vccq-sdhi2 {
169		compatible = "regulator-gpio";
170
171		regulator-name = "SDHI2 VccQ";
172		regulator-min-microvolt = <1800000>;
173		regulator-max-microvolt = <3300000>;
174
175		gpios = <&gpio5 30 GPIO_ACTIVE_HIGH>;
176		gpios-states = <1>;
177		states = <3300000 1
178			  1800000 0>;
179	};
180
181	audio_clock: audio_clock {
182		compatible = "fixed-clock";
183		#clock-cells = <0>;
184		clock-frequency = <11289600>;
185	};
186
187	rsnd_ak4643: sound {
188		compatible = "simple-audio-card";
189
190		simple-audio-card,format = "left_j";
191		simple-audio-card,bitclock-master = <&sndcodec>;
192		simple-audio-card,frame-master = <&sndcodec>;
193
194		sndcpu: simple-audio-card,cpu {
195			sound-dai = <&rcar_sound>;
196		};
197
198		sndcodec: simple-audio-card,codec {
199			sound-dai = <&ak4643>;
200			clocks = <&audio_clock>;
201		};
202	};
203
204	vga-encoder {
205		compatible = "adi,adv7123";
206
207		ports {
208			#address-cells = <1>;
209			#size-cells = <0>;
210
211			port@0 {
212				reg = <0>;
213				adv7123_in: endpoint {
214					remote-endpoint = <&du_out_rgb>;
215				};
216			};
217			port@1 {
218				reg = <1>;
219				adv7123_out: endpoint {
220					remote-endpoint = <&vga_in>;
221				};
222			};
223		};
224	};
225
226	vga {
227		compatible = "vga-connector";
228
229		port {
230			vga_in: endpoint {
231				remote-endpoint = <&adv7123_out>;
232			};
233		};
234	};
235
236	hdmi-in {
237		compatible = "hdmi-connector";
238		type = "a";
239
240		port {
241			hdmi_con_in: endpoint {
242				remote-endpoint = <&adv7612_in>;
243			};
244		};
245	};
246
247	cec_clock: cec-clock {
248		compatible = "fixed-clock";
249		#clock-cells = <0>;
250		clock-frequency = <12000000>;
251	};
252
253	hdmi-out {
254		compatible = "hdmi-connector";
255		type = "a";
256
257		port {
258			hdmi_con_out: endpoint {
259				remote-endpoint = <&adv7511_out>;
260			};
261		};
262	};
263
264	x2_clk: x2-clock {
265		compatible = "fixed-clock";
266		#clock-cells = <0>;
267		clock-frequency = <148500000>;
268	};
269
270	x13_clk: x13-clock {
271		compatible = "fixed-clock";
272		#clock-cells = <0>;
273		clock-frequency = <148500000>;
274	};
275
276	gpioi2c1: i2c-8 {
277		#address-cells = <1>;
278		#size-cells = <0>;
279		compatible = "i2c-gpio";
280		status = "disabled";
281		scl-gpios = <&gpio1 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
282		sda-gpios = <&gpio1 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
283		i2c-gpio,delay-us = <5>;
284	};
285
286	gpioi2c2: i2c-9 {
287		#address-cells = <1>;
288		#size-cells = <0>;
289		compatible = "i2c-gpio";
290		status = "disabled";
291		scl-gpios = <&gpio5 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
292		sda-gpios = <&gpio5 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
293		i2c-gpio,delay-us = <5>;
294	};
295
296	/*
297	 * IIC0/I2C0 is routed to EXIO connector A, pins 114 (SCL) + 116 (SDA) only.
298	 * We use the I2C demuxer, so the desired IP core can be selected at runtime
299	 * depending on the use case (e.g. DMA with IIC0 or slave support with I2C0).
300	 * Note: For testing the I2C slave feature, it is convenient to connect this
301	 * bus with IIC3 on pins 110 (SCL) + 112 (SDA), select I2C0 at runtime, and
302	 * instantiate the slave device at runtime according to the documentation.
303	 * You can then communicate with the slave via IIC3.
304	 *
305	 * IIC0/I2C0 does not appear to support fallback to GPIO.
306	 */
307	i2cexio0: i2c-10 {
308		compatible = "i2c-demux-pinctrl";
309		i2c-parent = <&iic0>, <&i2c0>;
310		i2c-bus-name = "i2c-exio0";
311		#address-cells = <1>;
312		#size-cells = <0>;
313	};
314
315	/*
316	 * IIC1/I2C1 is routed to EXIO connector A, pins 78 (SCL) + 80 (SDA).
317	 * This is similar to the arangement described for i2cexio0 (above)
318	 * with a fallback to GPIO also provided.
319	 */
320	i2cexio1: i2c-11 {
321		compatible = "i2c-demux-pinctrl";
322		i2c-parent = <&iic1>, <&i2c1>, <&gpioi2c1>;
323		i2c-bus-name = "i2c-exio1";
324		#address-cells = <1>;
325		#size-cells = <0>;
326	};
327
328        /*
329         * IIC2 and I2C2 may be switched using pinmux.
330         * A fallback to GPIO is also provided.
331         */
332	i2chdmi: i2c-12 {
333		compatible = "i2c-demux-pinctrl";
334		i2c-parent = <&iic2>, <&i2c2>, <&gpioi2c2>;
335		i2c-bus-name = "i2c-hdmi";
336		#address-cells = <1>;
337		#size-cells = <0>;
338
339		ak4643: codec@12 {
340			compatible = "asahi-kasei,ak4643";
341			#sound-dai-cells = <0>;
342			reg = <0x12>;
343		};
344
345		composite-in@20 {
346			compatible = "adi,adv7180";
347			reg = <0x20>;
348			remote = <&vin1>;
349
350			port {
351				adv7180: endpoint {
352					bus-width = <8>;
353					remote-endpoint = <&vin1ep0>;
354				};
355			};
356		};
357
358		hdmi@39 {
359			compatible = "adi,adv7511w";
360			reg = <0x39>;
361			interrupt-parent = <&gpio1>;
362			interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
363			clocks = <&cec_clock>;
364			clock-names = "cec";
365
366			adi,input-depth = <8>;
367			adi,input-colorspace = "rgb";
368			adi,input-clock = "1x";
369			adi,input-style = <1>;
370			adi,input-justification = "evenly";
371
372			ports {
373				#address-cells = <1>;
374				#size-cells = <0>;
375
376				port@0 {
377					reg = <0>;
378					adv7511_in: endpoint {
379						remote-endpoint = <&lvds0_out>;
380					};
381				};
382
383				port@1 {
384					reg = <1>;
385					adv7511_out: endpoint {
386						remote-endpoint = <&hdmi_con_out>;
387					};
388				};
389			};
390		};
391
392		hdmi-in@4c {
393			compatible = "adi,adv7612";
394			reg = <0x4c>;
395			interrupt-parent = <&gpio1>;
396			interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
397			default-input = <0>;
398
399			ports {
400				#address-cells = <1>;
401				#size-cells = <0>;
402
403				port@0 {
404					reg = <0>;
405					adv7612_in: endpoint {
406						remote-endpoint = <&hdmi_con_in>;
407					};
408				};
409
410				port@2 {
411					reg = <2>;
412					adv7612_out: endpoint {
413						remote-endpoint = <&vin0ep2>;
414					};
415				};
416			};
417		};
418	};
419
420	/*
421	 * IIC3 and I2C3 may be switched using pinmux.
422	 * IIC3/I2C3 does not appear to support fallback to GPIO.
423	 */
424	i2cpwr: i2c-13 {
425		compatible = "i2c-demux-pinctrl";
426		pinctrl-names = "default";
427		pinctrl-0 = <&pmic_irq_pins>;
428		i2c-parent = <&iic3>, <&i2c3>;
429		i2c-bus-name = "i2c-pwr";
430		#address-cells = <1>;
431		#size-cells = <0>;
432
433		pmic@58 {
434			compatible = "dlg,da9063";
435			reg = <0x58>;
436			interrupt-parent = <&irqc0>;
437			interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
438			interrupt-controller;
439
440			rtc {
441				compatible = "dlg,da9063-rtc";
442			};
443
444			wdt {
445				compatible = "dlg,da9063-watchdog";
446			};
447		};
448
449		vdd_dvfs: regulator@68 {
450			compatible = "dlg,da9210";
451			reg = <0x68>;
452			interrupt-parent = <&irqc0>;
453			interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
454
455			regulator-min-microvolt = <1000000>;
456			regulator-max-microvolt = <1000000>;
457			regulator-boot-on;
458			regulator-always-on;
459		};
460	};
461};
462
463&du {
464	pinctrl-0 = <&du_pins>;
465	pinctrl-names = "default";
466	status = "okay";
467
468	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 722>,
469		 <&x13_clk>, <&x2_clk>;
470	clock-names = "du.0", "du.1", "du.2", "dclkin.0", "dclkin.1";
471
472	ports {
473		port@0 {
474			endpoint {
475				remote-endpoint = <&adv7123_in>;
476			};
477		};
478	};
479};
480
481&lvds0 {
482	status = "okay";
483
484	ports {
485		port@1 {
486			endpoint {
487				remote-endpoint = <&adv7511_in>;
488			};
489		};
490	};
491};
492
493&lvds1 {
494	ports {
495		port@1 {
496			lvds_connector: endpoint {
497			};
498		};
499	};
500};
501
502&extal_clk {
503	clock-frequency = <20000000>;
504};
505
506&pfc {
507	pinctrl-0 = <&scif_clk_pins>;
508	pinctrl-names = "default";
509
510	du_pins: du {
511		groups = "du_rgb666", "du_sync_1", "du_clk_out_0";
512		function = "du";
513	};
514
515	scif0_pins: scif0 {
516		groups = "scif0_data";
517		function = "scif0";
518	};
519
520	scif_clk_pins: scif_clk {
521		groups = "scif_clk";
522		function = "scif_clk";
523	};
524
525	ether_pins: ether {
526		groups = "eth_link", "eth_mdio", "eth_rmii";
527		function = "eth";
528	};
529
530	phy1_pins: phy1 {
531		groups = "intc_irq0";
532		function = "intc";
533	};
534
535	scifa1_pins: scifa1 {
536		groups = "scifa1_data";
537		function = "scifa1";
538	};
539
540	sdhi0_pins: sd0 {
541		groups = "sdhi0_data4", "sdhi0_ctrl";
542		function = "sdhi0";
543		power-source = <3300>;
544	};
545
546	sdhi0_pins_uhs: sd0_uhs {
547		groups = "sdhi0_data4", "sdhi0_ctrl";
548		function = "sdhi0";
549		power-source = <1800>;
550	};
551
552	sdhi2_pins: sd2 {
553		groups = "sdhi2_data4", "sdhi2_ctrl";
554		function = "sdhi2";
555		power-source = <3300>;
556	};
557
558	sdhi2_pins_uhs: sd2_uhs {
559		groups = "sdhi2_data4", "sdhi2_ctrl";
560		function = "sdhi2";
561		power-source = <1800>;
562	};
563
564	mmc1_pins: mmc1 {
565		groups = "mmc1_data8", "mmc1_ctrl";
566		function = "mmc1";
567	};
568
569	qspi_pins: qspi {
570		groups = "qspi_ctrl", "qspi_data4";
571		function = "qspi";
572	};
573
574	msiof1_pins: msiof1 {
575		groups = "msiof1_clk", "msiof1_sync", "msiof1_rx",
576				 "msiof1_tx";
577		function = "msiof1";
578	};
579
580	i2c0_pins: i2c0 {
581		groups = "i2c0";
582		function = "i2c0";
583	};
584
585	iic0_pins: iic0 {
586		groups = "iic0";
587		function = "iic0";
588	};
589
590	i2c1_pins: i2c1 {
591		groups = "i2c1";
592		function = "i2c1";
593	};
594
595	iic1_pins: iic1 {
596		groups = "iic1";
597		function = "iic1";
598	};
599
600	i2c2_pins: i2c2 {
601		groups = "i2c2";
602		function = "i2c2";
603	};
604
605	iic2_pins: iic2 {
606		groups = "iic2";
607		function = "iic2";
608	};
609
610	i2c3_pins: i2c3 {
611		groups = "i2c3";
612		function = "i2c3";
613	};
614
615	iic3_pins: iic3 {
616		groups = "iic3";
617		function = "iic3";
618	};
619
620	pmic_irq_pins: pmicirq {
621		groups = "intc_irq2";
622		function = "intc";
623	};
624
625	hsusb_pins: hsusb {
626		groups = "usb0_ovc_vbus";
627		function = "usb0";
628	};
629
630	usb0_pins: usb0 {
631		groups = "usb0";
632		function = "usb0";
633	};
634
635	usb1_pins: usb1 {
636		groups = "usb1";
637		function = "usb1";
638	};
639
640	usb2_pins: usb2 {
641		groups = "usb2";
642		function = "usb2";
643	};
644
645	vin0_pins: vin0 {
646		groups = "vin0_data24", "vin0_sync", "vin0_clkenb", "vin0_clk";
647		function = "vin0";
648	};
649
650	vin1_pins: vin1 {
651		groups = "vin1_data8", "vin1_clk";
652		function = "vin1";
653	};
654
655	sound_pins: sound {
656		groups = "ssi0129_ctrl", "ssi0_data", "ssi1_data";
657		function = "ssi";
658	};
659
660	sound_clk_pins: sound_clk {
661		groups = "audio_clk_a";
662		function = "audio_clk";
663	};
664};
665
666&ether {
667	pinctrl-0 = <&ether_pins &phy1_pins>;
668	pinctrl-names = "default";
669
670	phy-handle = <&phy1>;
671	renesas,ether-link-active-low;
672	status = "okay";
673
674	phy1: ethernet-phy@1 {
675		reg = <1>;
676		interrupt-parent = <&irqc0>;
677		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
678		micrel,led-mode = <1>;
679	};
680};
681
682&cmt0 {
683	status = "okay";
684};
685
686&mmcif1 {
687	pinctrl-0 = <&mmc1_pins>;
688	pinctrl-names = "default";
689
690	vmmc-supply = <&fixedregulator3v3>;
691	bus-width = <8>;
692	non-removable;
693	status = "okay";
694};
695
696&sata1 {
697	status = "okay";
698};
699
700&qspi {
701	pinctrl-0 = <&qspi_pins>;
702	pinctrl-names = "default";
703
704	status = "okay";
705
706	flash: flash@0 {
707		compatible = "spansion,s25fl512s", "jedec,spi-nor";
708		reg = <0>;
709		spi-max-frequency = <30000000>;
710		spi-tx-bus-width = <4>;
711		spi-rx-bus-width = <4>;
712		spi-cpha;
713		spi-cpol;
714		m25p,fast-read;
715
716		partitions {
717			compatible = "fixed-partitions";
718			#address-cells = <1>;
719			#size-cells = <1>;
720
721			partition@0 {
722				label = "loader";
723				reg = <0x00000000 0x00040000>;
724				read-only;
725			};
726			partition@40000 {
727				label = "user";
728				reg = <0x00040000 0x00400000>;
729				read-only;
730			};
731			partition@440000 {
732				label = "flash";
733				reg = <0x00440000 0x03bc0000>;
734			};
735		};
736	};
737};
738
739&scif0 {
740	pinctrl-0 = <&scif0_pins>;
741	pinctrl-names = "default";
742
743	status = "okay";
744};
745
746&scifa1 {
747	pinctrl-0 = <&scifa1_pins>;
748	pinctrl-names = "default";
749
750	status = "okay";
751};
752
753&scif_clk {
754	clock-frequency = <14745600>;
755};
756
757&msiof1 {
758	pinctrl-0 = <&msiof1_pins>;
759	pinctrl-names = "default";
760
761	status = "okay";
762
763	pmic: pmic@0 {
764		compatible = "renesas,r2a11302ft";
765		reg = <0>;
766		spi-max-frequency = <6000000>;
767		spi-cpol;
768		spi-cpha;
769	};
770};
771
772&sdhi0 {
773	pinctrl-0 = <&sdhi0_pins>;
774	pinctrl-1 = <&sdhi0_pins_uhs>;
775	pinctrl-names = "default", "state_uhs";
776
777	vmmc-supply = <&vcc_sdhi0>;
778	vqmmc-supply = <&vccq_sdhi0>;
779	cd-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>;
780	sd-uhs-sdr50;
781	sd-uhs-sdr104;
782	status = "okay";
783};
784
785&sdhi2 {
786	pinctrl-0 = <&sdhi2_pins>;
787	pinctrl-1 = <&sdhi2_pins_uhs>;
788	pinctrl-names = "default", "state_uhs";
789
790	vmmc-supply = <&vcc_sdhi2>;
791	vqmmc-supply = <&vccq_sdhi2>;
792	cd-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>;
793	sd-uhs-sdr50;
794	status = "okay";
795};
796
797&cpu0 {
798	cpu0-supply = <&vdd_dvfs>;
799};
800
801&i2c0	{
802	pinctrl-0 = <&i2c0_pins>;
803	pinctrl-names = "i2c-exio0";
804};
805
806&iic0	{
807	pinctrl-0 = <&iic0_pins>;
808	pinctrl-names = "i2c-exio0";
809};
810
811&i2c1	{
812	pinctrl-0 = <&i2c1_pins>;
813	pinctrl-names = "i2c-exio1";
814};
815
816&iic1	{
817	pinctrl-0 = <&iic1_pins>;
818	pinctrl-names = "i2c-exio1";
819};
820
821&i2c2	{
822	pinctrl-0 = <&i2c2_pins>;
823	pinctrl-names = "i2c-hdmi";
824
825	clock-frequency = <100000>;
826};
827
828&iic2	{
829	pinctrl-0 = <&iic2_pins>;
830	pinctrl-names = "i2c-hdmi";
831
832	clock-frequency = <100000>;
833};
834
835&i2c3	{
836	pinctrl-0 = <&i2c3_pins>;
837	pinctrl-names = "i2c-pwr";
838};
839
840&iic3	{
841	pinctrl-0 = <&iic3_pins>;
842	pinctrl-names = "i2c-pwr";
843};
844
845&pci0 {
846	status = "okay";
847	pinctrl-0 = <&usb0_pins>;
848	pinctrl-names = "default";
849};
850
851&pci1 {
852	status = "okay";
853	pinctrl-0 = <&usb1_pins>;
854	pinctrl-names = "default";
855};
856
857&xhci {
858	status = "okay";
859	pinctrl-0 = <&usb2_pins>;
860	pinctrl-names = "default";
861};
862
863&pci2 {
864	status = "okay";
865	pinctrl-0 = <&usb2_pins>;
866	pinctrl-names = "default";
867};
868
869&hsusb {
870	status = "okay";
871	pinctrl-0 = <&hsusb_pins>;
872	pinctrl-names = "default";
873	renesas,enable-gpio = <&gpio5 18 GPIO_ACTIVE_HIGH>;
874};
875
876&usbphy {
877	status = "okay";
878};
879
880/* HDMI video input */
881&vin0 {
882	pinctrl-0 = <&vin0_pins>;
883	pinctrl-names = "default";
884
885	status = "okay";
886
887	port {
888		vin0ep2: endpoint {
889			remote-endpoint = <&adv7612_out>;
890			bus-width = <24>;
891			hsync-active = <0>;
892			vsync-active = <0>;
893			pclk-sample = <1>;
894			data-active = <1>;
895		};
896	};
897};
898
899/* composite video input */
900&vin1 {
901	pinctrl-0 = <&vin1_pins>;
902	pinctrl-names = "default";
903
904	status = "okay";
905
906	port {
907		vin1ep0: endpoint {
908			remote-endpoint = <&adv7180>;
909			bus-width = <8>;
910		};
911	};
912};
913
914&rcar_sound {
915	pinctrl-0 = <&sound_pins &sound_clk_pins>;
916	pinctrl-names = "default";
917
918	/* Single DAI */
919	#sound-dai-cells = <0>;
920
921	status = "okay";
922
923	rcar_sound,dai {
924		dai0 {
925			playback = <&ssi0 &src2 &dvc0>;
926			capture  = <&ssi1 &src3 &dvc1>;
927		};
928	};
929};
930
931&rwdt {
932	timeout-sec = <60>;
933	status = "okay";
934};
935
936&ssi1 {
937	shared-pin;
938};
939