1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /*
3 * Copyright (c) 2011 Bosch Sensortec GmbH
4 * Copyright (c) 2011 Unixphere
5 *
6 * This driver adds support for Bosch Sensortec's digital acceleration
7 * sensors BMA150 and SMB380.
8 * The SMB380 is fully compatible with BMA150 and only differs in packaging.
9 *
10 * The datasheet for the BMA150 chip can be found here:
11 * http://www.bosch-sensortec.com/content/language1/downloads/BST-BMA150-DS000-07.pdf
12 */
13 #include <linux/kernel.h>
14 #include <linux/module.h>
15 #include <linux/i2c.h>
16 #include <linux/input.h>
17 #include <linux/interrupt.h>
18 #include <linux/delay.h>
19 #include <linux/slab.h>
20 #include <linux/pm.h>
21 #include <linux/pm_runtime.h>
22 #include <linux/bma150.h>
23
24 #define ABSMAX_ACC_VAL 0x01FF
25 #define ABSMIN_ACC_VAL -(ABSMAX_ACC_VAL)
26
27 /* Each axis is represented by a 2-byte data word */
28 #define BMA150_XYZ_DATA_SIZE 6
29
30 /* Input poll interval in milliseconds */
31 #define BMA150_POLL_INTERVAL 10
32 #define BMA150_POLL_MAX 200
33 #define BMA150_POLL_MIN 0
34
35 #define BMA150_MODE_NORMAL 0
36 #define BMA150_MODE_SLEEP 2
37 #define BMA150_MODE_WAKE_UP 3
38
39 /* Data register addresses */
40 #define BMA150_DATA_0_REG 0x00
41 #define BMA150_DATA_1_REG 0x01
42 #define BMA150_DATA_2_REG 0x02
43
44 /* Control register addresses */
45 #define BMA150_CTRL_0_REG 0x0A
46 #define BMA150_CTRL_1_REG 0x0B
47 #define BMA150_CTRL_2_REG 0x14
48 #define BMA150_CTRL_3_REG 0x15
49
50 /* Configuration/Setting register addresses */
51 #define BMA150_CFG_0_REG 0x0C
52 #define BMA150_CFG_1_REG 0x0D
53 #define BMA150_CFG_2_REG 0x0E
54 #define BMA150_CFG_3_REG 0x0F
55 #define BMA150_CFG_4_REG 0x10
56 #define BMA150_CFG_5_REG 0x11
57
58 #define BMA150_CHIP_ID 2
59 #define BMA150_CHIP_ID_REG BMA150_DATA_0_REG
60
61 #define BMA150_ACC_X_LSB_REG BMA150_DATA_2_REG
62
63 #define BMA150_SLEEP_POS 0
64 #define BMA150_SLEEP_MSK 0x01
65 #define BMA150_SLEEP_REG BMA150_CTRL_0_REG
66
67 #define BMA150_BANDWIDTH_POS 0
68 #define BMA150_BANDWIDTH_MSK 0x07
69 #define BMA150_BANDWIDTH_REG BMA150_CTRL_2_REG
70
71 #define BMA150_RANGE_POS 3
72 #define BMA150_RANGE_MSK 0x18
73 #define BMA150_RANGE_REG BMA150_CTRL_2_REG
74
75 #define BMA150_WAKE_UP_POS 0
76 #define BMA150_WAKE_UP_MSK 0x01
77 #define BMA150_WAKE_UP_REG BMA150_CTRL_3_REG
78
79 #define BMA150_SW_RES_POS 1
80 #define BMA150_SW_RES_MSK 0x02
81 #define BMA150_SW_RES_REG BMA150_CTRL_0_REG
82
83 /* Any-motion interrupt register fields */
84 #define BMA150_ANY_MOTION_EN_POS 6
85 #define BMA150_ANY_MOTION_EN_MSK 0x40
86 #define BMA150_ANY_MOTION_EN_REG BMA150_CTRL_1_REG
87
88 #define BMA150_ANY_MOTION_DUR_POS 6
89 #define BMA150_ANY_MOTION_DUR_MSK 0xC0
90 #define BMA150_ANY_MOTION_DUR_REG BMA150_CFG_5_REG
91
92 #define BMA150_ANY_MOTION_THRES_REG BMA150_CFG_4_REG
93
94 /* Advanced interrupt register fields */
95 #define BMA150_ADV_INT_EN_POS 6
96 #define BMA150_ADV_INT_EN_MSK 0x40
97 #define BMA150_ADV_INT_EN_REG BMA150_CTRL_3_REG
98
99 /* High-G interrupt register fields */
100 #define BMA150_HIGH_G_EN_POS 1
101 #define BMA150_HIGH_G_EN_MSK 0x02
102 #define BMA150_HIGH_G_EN_REG BMA150_CTRL_1_REG
103
104 #define BMA150_HIGH_G_HYST_POS 3
105 #define BMA150_HIGH_G_HYST_MSK 0x38
106 #define BMA150_HIGH_G_HYST_REG BMA150_CFG_5_REG
107
108 #define BMA150_HIGH_G_DUR_REG BMA150_CFG_3_REG
109 #define BMA150_HIGH_G_THRES_REG BMA150_CFG_2_REG
110
111 /* Low-G interrupt register fields */
112 #define BMA150_LOW_G_EN_POS 0
113 #define BMA150_LOW_G_EN_MSK 0x01
114 #define BMA150_LOW_G_EN_REG BMA150_CTRL_1_REG
115
116 #define BMA150_LOW_G_HYST_POS 0
117 #define BMA150_LOW_G_HYST_MSK 0x07
118 #define BMA150_LOW_G_HYST_REG BMA150_CFG_5_REG
119
120 #define BMA150_LOW_G_DUR_REG BMA150_CFG_1_REG
121 #define BMA150_LOW_G_THRES_REG BMA150_CFG_0_REG
122
123 struct bma150_data {
124 struct i2c_client *client;
125 struct input_dev *input;
126 u8 mode;
127 };
128
129 /*
130 * The settings for the given range, bandwidth and interrupt features
131 * are stated and verified by Bosch Sensortec where they are configured
132 * to provide a generic sensitivity performance.
133 */
134 static const struct bma150_cfg default_cfg = {
135 .any_motion_int = 1,
136 .hg_int = 1,
137 .lg_int = 1,
138 .any_motion_dur = 0,
139 .any_motion_thres = 0,
140 .hg_hyst = 0,
141 .hg_dur = 150,
142 .hg_thres = 160,
143 .lg_hyst = 0,
144 .lg_dur = 150,
145 .lg_thres = 20,
146 .range = BMA150_RANGE_2G,
147 .bandwidth = BMA150_BW_50HZ
148 };
149
bma150_write_byte(struct i2c_client * client,u8 reg,u8 val)150 static int bma150_write_byte(struct i2c_client *client, u8 reg, u8 val)
151 {
152 s32 ret;
153
154 /* As per specification, disable irq in between register writes */
155 if (client->irq)
156 disable_irq_nosync(client->irq);
157
158 ret = i2c_smbus_write_byte_data(client, reg, val);
159
160 if (client->irq)
161 enable_irq(client->irq);
162
163 return ret;
164 }
165
bma150_set_reg_bits(struct i2c_client * client,int val,int shift,u8 mask,u8 reg)166 static int bma150_set_reg_bits(struct i2c_client *client,
167 int val, int shift, u8 mask, u8 reg)
168 {
169 int data;
170
171 data = i2c_smbus_read_byte_data(client, reg);
172 if (data < 0)
173 return data;
174
175 data = (data & ~mask) | ((val << shift) & mask);
176 return bma150_write_byte(client, reg, data);
177 }
178
bma150_set_mode(struct bma150_data * bma150,u8 mode)179 static int bma150_set_mode(struct bma150_data *bma150, u8 mode)
180 {
181 int error;
182
183 error = bma150_set_reg_bits(bma150->client, mode, BMA150_WAKE_UP_POS,
184 BMA150_WAKE_UP_MSK, BMA150_WAKE_UP_REG);
185 if (error)
186 return error;
187
188 error = bma150_set_reg_bits(bma150->client, mode, BMA150_SLEEP_POS,
189 BMA150_SLEEP_MSK, BMA150_SLEEP_REG);
190 if (error)
191 return error;
192
193 if (mode == BMA150_MODE_NORMAL)
194 usleep_range(2000, 2100);
195
196 bma150->mode = mode;
197 return 0;
198 }
199
bma150_soft_reset(struct bma150_data * bma150)200 static int bma150_soft_reset(struct bma150_data *bma150)
201 {
202 int error;
203
204 error = bma150_set_reg_bits(bma150->client, 1, BMA150_SW_RES_POS,
205 BMA150_SW_RES_MSK, BMA150_SW_RES_REG);
206 if (error)
207 return error;
208
209 usleep_range(2000, 2100);
210 return 0;
211 }
212
bma150_set_range(struct bma150_data * bma150,u8 range)213 static int bma150_set_range(struct bma150_data *bma150, u8 range)
214 {
215 return bma150_set_reg_bits(bma150->client, range, BMA150_RANGE_POS,
216 BMA150_RANGE_MSK, BMA150_RANGE_REG);
217 }
218
bma150_set_bandwidth(struct bma150_data * bma150,u8 bw)219 static int bma150_set_bandwidth(struct bma150_data *bma150, u8 bw)
220 {
221 return bma150_set_reg_bits(bma150->client, bw, BMA150_BANDWIDTH_POS,
222 BMA150_BANDWIDTH_MSK, BMA150_BANDWIDTH_REG);
223 }
224
bma150_set_low_g_interrupt(struct bma150_data * bma150,u8 enable,u8 hyst,u8 dur,u8 thres)225 static int bma150_set_low_g_interrupt(struct bma150_data *bma150,
226 u8 enable, u8 hyst, u8 dur, u8 thres)
227 {
228 int error;
229
230 error = bma150_set_reg_bits(bma150->client, hyst,
231 BMA150_LOW_G_HYST_POS, BMA150_LOW_G_HYST_MSK,
232 BMA150_LOW_G_HYST_REG);
233 if (error)
234 return error;
235
236 error = bma150_write_byte(bma150->client, BMA150_LOW_G_DUR_REG, dur);
237 if (error)
238 return error;
239
240 error = bma150_write_byte(bma150->client, BMA150_LOW_G_THRES_REG, thres);
241 if (error)
242 return error;
243
244 return bma150_set_reg_bits(bma150->client, !!enable,
245 BMA150_LOW_G_EN_POS, BMA150_LOW_G_EN_MSK,
246 BMA150_LOW_G_EN_REG);
247 }
248
bma150_set_high_g_interrupt(struct bma150_data * bma150,u8 enable,u8 hyst,u8 dur,u8 thres)249 static int bma150_set_high_g_interrupt(struct bma150_data *bma150,
250 u8 enable, u8 hyst, u8 dur, u8 thres)
251 {
252 int error;
253
254 error = bma150_set_reg_bits(bma150->client, hyst,
255 BMA150_HIGH_G_HYST_POS, BMA150_HIGH_G_HYST_MSK,
256 BMA150_HIGH_G_HYST_REG);
257 if (error)
258 return error;
259
260 error = bma150_write_byte(bma150->client,
261 BMA150_HIGH_G_DUR_REG, dur);
262 if (error)
263 return error;
264
265 error = bma150_write_byte(bma150->client,
266 BMA150_HIGH_G_THRES_REG, thres);
267 if (error)
268 return error;
269
270 return bma150_set_reg_bits(bma150->client, !!enable,
271 BMA150_HIGH_G_EN_POS, BMA150_HIGH_G_EN_MSK,
272 BMA150_HIGH_G_EN_REG);
273 }
274
275
bma150_set_any_motion_interrupt(struct bma150_data * bma150,u8 enable,u8 dur,u8 thres)276 static int bma150_set_any_motion_interrupt(struct bma150_data *bma150,
277 u8 enable, u8 dur, u8 thres)
278 {
279 int error;
280
281 error = bma150_set_reg_bits(bma150->client, dur,
282 BMA150_ANY_MOTION_DUR_POS,
283 BMA150_ANY_MOTION_DUR_MSK,
284 BMA150_ANY_MOTION_DUR_REG);
285 if (error)
286 return error;
287
288 error = bma150_write_byte(bma150->client,
289 BMA150_ANY_MOTION_THRES_REG, thres);
290 if (error)
291 return error;
292
293 error = bma150_set_reg_bits(bma150->client, !!enable,
294 BMA150_ADV_INT_EN_POS, BMA150_ADV_INT_EN_MSK,
295 BMA150_ADV_INT_EN_REG);
296 if (error)
297 return error;
298
299 return bma150_set_reg_bits(bma150->client, !!enable,
300 BMA150_ANY_MOTION_EN_POS,
301 BMA150_ANY_MOTION_EN_MSK,
302 BMA150_ANY_MOTION_EN_REG);
303 }
304
bma150_report_xyz(struct bma150_data * bma150)305 static void bma150_report_xyz(struct bma150_data *bma150)
306 {
307 u8 data[BMA150_XYZ_DATA_SIZE];
308 s16 x, y, z;
309 s32 ret;
310
311 ret = i2c_smbus_read_i2c_block_data(bma150->client,
312 BMA150_ACC_X_LSB_REG, BMA150_XYZ_DATA_SIZE, data);
313 if (ret != BMA150_XYZ_DATA_SIZE)
314 return;
315
316 x = ((0xc0 & data[0]) >> 6) | (data[1] << 2);
317 y = ((0xc0 & data[2]) >> 6) | (data[3] << 2);
318 z = ((0xc0 & data[4]) >> 6) | (data[5] << 2);
319
320 x = sign_extend32(x, 9);
321 y = sign_extend32(y, 9);
322 z = sign_extend32(z, 9);
323
324 input_report_abs(bma150->input, ABS_X, x);
325 input_report_abs(bma150->input, ABS_Y, y);
326 input_report_abs(bma150->input, ABS_Z, z);
327 input_sync(bma150->input);
328 }
329
bma150_irq_thread(int irq,void * dev)330 static irqreturn_t bma150_irq_thread(int irq, void *dev)
331 {
332 bma150_report_xyz(dev);
333
334 return IRQ_HANDLED;
335 }
336
bma150_poll(struct input_dev * input)337 static void bma150_poll(struct input_dev *input)
338 {
339 struct bma150_data *bma150 = input_get_drvdata(input);
340
341 bma150_report_xyz(bma150);
342 }
343
bma150_open(struct input_dev * input)344 static int bma150_open(struct input_dev *input)
345 {
346 struct bma150_data *bma150 = input_get_drvdata(input);
347 int error;
348
349 error = pm_runtime_get_sync(&bma150->client->dev);
350 if (error < 0 && error != -ENOSYS)
351 return error;
352
353 /*
354 * See if runtime PM woke up the device. If runtime PM
355 * is disabled we need to do it ourselves.
356 */
357 if (bma150->mode != BMA150_MODE_NORMAL) {
358 error = bma150_set_mode(bma150, BMA150_MODE_NORMAL);
359 if (error)
360 return error;
361 }
362
363 return 0;
364 }
365
bma150_close(struct input_dev * input)366 static void bma150_close(struct input_dev *input)
367 {
368 struct bma150_data *bma150 = input_get_drvdata(input);
369
370 pm_runtime_put_sync(&bma150->client->dev);
371
372 if (bma150->mode != BMA150_MODE_SLEEP)
373 bma150_set_mode(bma150, BMA150_MODE_SLEEP);
374 }
375
bma150_initialize(struct bma150_data * bma150,const struct bma150_cfg * cfg)376 static int bma150_initialize(struct bma150_data *bma150,
377 const struct bma150_cfg *cfg)
378 {
379 int error;
380
381 error = bma150_soft_reset(bma150);
382 if (error)
383 return error;
384
385 error = bma150_set_bandwidth(bma150, cfg->bandwidth);
386 if (error)
387 return error;
388
389 error = bma150_set_range(bma150, cfg->range);
390 if (error)
391 return error;
392
393 if (bma150->client->irq) {
394 error = bma150_set_any_motion_interrupt(bma150,
395 cfg->any_motion_int,
396 cfg->any_motion_dur,
397 cfg->any_motion_thres);
398 if (error)
399 return error;
400
401 error = bma150_set_high_g_interrupt(bma150,
402 cfg->hg_int, cfg->hg_hyst,
403 cfg->hg_dur, cfg->hg_thres);
404 if (error)
405 return error;
406
407 error = bma150_set_low_g_interrupt(bma150,
408 cfg->lg_int, cfg->lg_hyst,
409 cfg->lg_dur, cfg->lg_thres);
410 if (error)
411 return error;
412 }
413
414 return bma150_set_mode(bma150, BMA150_MODE_SLEEP);
415 }
416
bma150_probe(struct i2c_client * client,const struct i2c_device_id * id)417 static int bma150_probe(struct i2c_client *client,
418 const struct i2c_device_id *id)
419 {
420 const struct bma150_platform_data *pdata =
421 dev_get_platdata(&client->dev);
422 const struct bma150_cfg *cfg;
423 struct bma150_data *bma150;
424 struct input_dev *idev;
425 int chip_id;
426 int error;
427
428 if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
429 dev_err(&client->dev, "i2c_check_functionality error\n");
430 return -EIO;
431 }
432
433 chip_id = i2c_smbus_read_byte_data(client, BMA150_CHIP_ID_REG);
434 if (chip_id != BMA150_CHIP_ID) {
435 dev_err(&client->dev, "BMA150 chip id error: %d\n", chip_id);
436 return -EINVAL;
437 }
438
439 bma150 = devm_kzalloc(&client->dev, sizeof(*bma150), GFP_KERNEL);
440 if (!bma150)
441 return -ENOMEM;
442
443 bma150->client = client;
444
445 if (pdata) {
446 if (pdata->irq_gpio_cfg) {
447 error = pdata->irq_gpio_cfg();
448 if (error) {
449 dev_err(&client->dev,
450 "IRQ GPIO conf. error %d, error %d\n",
451 client->irq, error);
452 return error;
453 }
454 }
455 cfg = &pdata->cfg;
456 } else {
457 cfg = &default_cfg;
458 }
459
460 error = bma150_initialize(bma150, cfg);
461 if (error)
462 return error;
463
464 idev = devm_input_allocate_device(&bma150->client->dev);
465 if (!idev)
466 return -ENOMEM;
467
468 input_set_drvdata(idev, bma150);
469 bma150->input = idev;
470
471 idev->name = BMA150_DRIVER;
472 idev->phys = BMA150_DRIVER "/input0";
473 idev->id.bustype = BUS_I2C;
474
475 idev->open = bma150_open;
476 idev->close = bma150_close;
477
478 input_set_abs_params(idev, ABS_X, ABSMIN_ACC_VAL, ABSMAX_ACC_VAL, 0, 0);
479 input_set_abs_params(idev, ABS_Y, ABSMIN_ACC_VAL, ABSMAX_ACC_VAL, 0, 0);
480 input_set_abs_params(idev, ABS_Z, ABSMIN_ACC_VAL, ABSMAX_ACC_VAL, 0, 0);
481
482 if (client->irq <= 0) {
483 error = input_setup_polling(idev, bma150_poll);
484 if (error)
485 return error;
486
487 input_set_poll_interval(idev, BMA150_POLL_INTERVAL);
488 input_set_min_poll_interval(idev, BMA150_POLL_MIN);
489 input_set_max_poll_interval(idev, BMA150_POLL_MAX);
490 }
491
492 error = input_register_device(idev);
493 if (error)
494 return error;
495
496 if (client->irq > 0) {
497 error = devm_request_threaded_irq(&client->dev, client->irq,
498 NULL, bma150_irq_thread,
499 IRQF_TRIGGER_RISING | IRQF_ONESHOT,
500 BMA150_DRIVER, bma150);
501 if (error) {
502 dev_err(&client->dev,
503 "irq request failed %d, error %d\n",
504 client->irq, error);
505 return error;
506 }
507 }
508
509 i2c_set_clientdata(client, bma150);
510
511 pm_runtime_enable(&client->dev);
512
513 return 0;
514 }
515
bma150_remove(struct i2c_client * client)516 static int bma150_remove(struct i2c_client *client)
517 {
518 pm_runtime_disable(&client->dev);
519
520 return 0;
521 }
522
bma150_suspend(struct device * dev)523 static int __maybe_unused bma150_suspend(struct device *dev)
524 {
525 struct i2c_client *client = to_i2c_client(dev);
526 struct bma150_data *bma150 = i2c_get_clientdata(client);
527
528 return bma150_set_mode(bma150, BMA150_MODE_SLEEP);
529 }
530
bma150_resume(struct device * dev)531 static int __maybe_unused bma150_resume(struct device *dev)
532 {
533 struct i2c_client *client = to_i2c_client(dev);
534 struct bma150_data *bma150 = i2c_get_clientdata(client);
535
536 return bma150_set_mode(bma150, BMA150_MODE_NORMAL);
537 }
538
539 static UNIVERSAL_DEV_PM_OPS(bma150_pm, bma150_suspend, bma150_resume, NULL);
540
541 static const struct i2c_device_id bma150_id[] = {
542 { "bma150", 0 },
543 { "smb380", 0 },
544 { "bma023", 0 },
545 { }
546 };
547
548 MODULE_DEVICE_TABLE(i2c, bma150_id);
549
550 static struct i2c_driver bma150_driver = {
551 .driver = {
552 .name = BMA150_DRIVER,
553 .pm = &bma150_pm,
554 },
555 .class = I2C_CLASS_HWMON,
556 .id_table = bma150_id,
557 .probe = bma150_probe,
558 .remove = bma150_remove,
559 };
560
561 module_i2c_driver(bma150_driver);
562
563 MODULE_AUTHOR("Albert Zhang <xu.zhang@bosch-sensortec.com>");
564 MODULE_DESCRIPTION("BMA150 driver");
565 MODULE_LICENSE("GPL");
566
