1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /*
3 * SMP support for power macintosh.
4 *
5 * We support both the old "powersurge" SMP architecture
6 * and the current Core99 (G4 PowerMac) machines.
7 *
8 * Note that we don't support the very first rev. of
9 * Apple/DayStar 2 CPUs board, the one with the funky
10 * watchdog. Hopefully, none of these should be there except
11 * maybe internally to Apple. I should probably still add some
12 * code to detect this card though and disable SMP. --BenH.
13 *
14 * Support Macintosh G4 SMP by Troy Benjegerdes (hozer@drgw.net)
15 * and Ben Herrenschmidt <benh@kernel.crashing.org>.
16 *
17 * Support for DayStar quad CPU cards
18 * Copyright (C) XLR8, Inc. 1994-2000
19 */
20 #include <linux/kernel.h>
21 #include <linux/sched.h>
22 #include <linux/sched/hotplug.h>
23 #include <linux/smp.h>
24 #include <linux/interrupt.h>
25 #include <linux/kernel_stat.h>
26 #include <linux/delay.h>
27 #include <linux/init.h>
28 #include <linux/spinlock.h>
29 #include <linux/errno.h>
30 #include <linux/hardirq.h>
31 #include <linux/cpu.h>
32 #include <linux/compiler.h>
33 #include <linux/pgtable.h>
34
35 #include <asm/ptrace.h>
36 #include <linux/atomic.h>
37 #include <asm/code-patching.h>
38 #include <asm/irq.h>
39 #include <asm/page.h>
40 #include <asm/sections.h>
41 #include <asm/io.h>
42 #include <asm/prom.h>
43 #include <asm/smp.h>
44 #include <asm/machdep.h>
45 #include <asm/pmac_feature.h>
46 #include <asm/time.h>
47 #include <asm/mpic.h>
48 #include <asm/cacheflush.h>
49 #include <asm/keylargo.h>
50 #include <asm/pmac_low_i2c.h>
51 #include <asm/pmac_pfunc.h>
52 #include <asm/inst.h>
53
54 #include "pmac.h"
55
56 #undef DEBUG
57
58 #ifdef DEBUG
59 #define DBG(fmt...) udbg_printf(fmt)
60 #else
61 #define DBG(fmt...)
62 #endif
63
64 extern void __secondary_start_pmac_0(void);
65
66 static void (*pmac_tb_freeze)(int freeze);
67 static u64 timebase;
68 static int tb_req;
69
70 #ifdef CONFIG_PPC_PMAC32_PSURGE
71
72 /*
73 * Powersurge (old powermac SMP) support.
74 */
75
76 /* Addresses for powersurge registers */
77 #define HAMMERHEAD_BASE 0xf8000000
78 #define HHEAD_CONFIG 0x90
79 #define HHEAD_SEC_INTR 0xc0
80
81 /* register for interrupting the primary processor on the powersurge */
82 /* N.B. this is actually the ethernet ROM! */
83 #define PSURGE_PRI_INTR 0xf3019000
84
85 /* register for storing the start address for the secondary processor */
86 /* N.B. this is the PCI config space address register for the 1st bridge */
87 #define PSURGE_START 0xf2800000
88
89 /* Daystar/XLR8 4-CPU card */
90 #define PSURGE_QUAD_REG_ADDR 0xf8800000
91
92 #define PSURGE_QUAD_IRQ_SET 0
93 #define PSURGE_QUAD_IRQ_CLR 1
94 #define PSURGE_QUAD_IRQ_PRIMARY 2
95 #define PSURGE_QUAD_CKSTOP_CTL 3
96 #define PSURGE_QUAD_PRIMARY_ARB 4
97 #define PSURGE_QUAD_BOARD_ID 6
98 #define PSURGE_QUAD_WHICH_CPU 7
99 #define PSURGE_QUAD_CKSTOP_RDBK 8
100 #define PSURGE_QUAD_RESET_CTL 11
101
102 #define PSURGE_QUAD_OUT(r, v) (out_8(quad_base + ((r) << 4) + 4, (v)))
103 #define PSURGE_QUAD_IN(r) (in_8(quad_base + ((r) << 4) + 4) & 0x0f)
104 #define PSURGE_QUAD_BIS(r, v) (PSURGE_QUAD_OUT((r), PSURGE_QUAD_IN(r) | (v)))
105 #define PSURGE_QUAD_BIC(r, v) (PSURGE_QUAD_OUT((r), PSURGE_QUAD_IN(r) & ~(v)))
106
107 /* virtual addresses for the above */
108 static volatile u8 __iomem *hhead_base;
109 static volatile u8 __iomem *quad_base;
110 static volatile u32 __iomem *psurge_pri_intr;
111 static volatile u8 __iomem *psurge_sec_intr;
112 static volatile u32 __iomem *psurge_start;
113
114 /* values for psurge_type */
115 #define PSURGE_NONE -1
116 #define PSURGE_DUAL 0
117 #define PSURGE_QUAD_OKEE 1
118 #define PSURGE_QUAD_COTTON 2
119 #define PSURGE_QUAD_ICEGRASS 3
120
121 /* what sort of powersurge board we have */
122 static int psurge_type = PSURGE_NONE;
123
124 /* irq for secondary cpus to report */
125 static struct irq_domain *psurge_host;
126 int psurge_secondary_virq;
127
128 /*
129 * Set and clear IPIs for powersurge.
130 */
psurge_set_ipi(int cpu)131 static inline void psurge_set_ipi(int cpu)
132 {
133 if (psurge_type == PSURGE_NONE)
134 return;
135 if (cpu == 0)
136 in_be32(psurge_pri_intr);
137 else if (psurge_type == PSURGE_DUAL)
138 out_8(psurge_sec_intr, 0);
139 else
140 PSURGE_QUAD_OUT(PSURGE_QUAD_IRQ_SET, 1 << cpu);
141 }
142
psurge_clr_ipi(int cpu)143 static inline void psurge_clr_ipi(int cpu)
144 {
145 if (cpu > 0) {
146 switch(psurge_type) {
147 case PSURGE_DUAL:
148 out_8(psurge_sec_intr, ~0);
149 case PSURGE_NONE:
150 break;
151 default:
152 PSURGE_QUAD_OUT(PSURGE_QUAD_IRQ_CLR, 1 << cpu);
153 }
154 }
155 }
156
157 /*
158 * On powersurge (old SMP powermac architecture) we don't have
159 * separate IPIs for separate messages like openpic does. Instead
160 * use the generic demux helpers
161 * -- paulus.
162 */
psurge_ipi_intr(int irq,void * d)163 static irqreturn_t psurge_ipi_intr(int irq, void *d)
164 {
165 psurge_clr_ipi(smp_processor_id());
166 smp_ipi_demux();
167
168 return IRQ_HANDLED;
169 }
170
smp_psurge_cause_ipi(int cpu)171 static void smp_psurge_cause_ipi(int cpu)
172 {
173 psurge_set_ipi(cpu);
174 }
175
psurge_host_map(struct irq_domain * h,unsigned int virq,irq_hw_number_t hw)176 static int psurge_host_map(struct irq_domain *h, unsigned int virq,
177 irq_hw_number_t hw)
178 {
179 irq_set_chip_and_handler(virq, &dummy_irq_chip, handle_percpu_irq);
180
181 return 0;
182 }
183
184 static const struct irq_domain_ops psurge_host_ops = {
185 .map = psurge_host_map,
186 };
187
psurge_secondary_ipi_init(void)188 static int psurge_secondary_ipi_init(void)
189 {
190 int rc = -ENOMEM;
191
192 psurge_host = irq_domain_add_nomap(NULL, ~0, &psurge_host_ops, NULL);
193
194 if (psurge_host)
195 psurge_secondary_virq = irq_create_direct_mapping(psurge_host);
196
197 if (psurge_secondary_virq)
198 rc = request_irq(psurge_secondary_virq, psurge_ipi_intr,
199 IRQF_PERCPU | IRQF_NO_THREAD, "IPI", NULL);
200
201 if (rc)
202 pr_err("Failed to setup secondary cpu IPI\n");
203
204 return rc;
205 }
206
207 /*
208 * Determine a quad card presence. We read the board ID register, we
209 * force the data bus to change to something else, and we read it again.
210 * It it's stable, then the register probably exist (ugh !)
211 */
psurge_quad_probe(void)212 static int __init psurge_quad_probe(void)
213 {
214 int type;
215 unsigned int i;
216
217 type = PSURGE_QUAD_IN(PSURGE_QUAD_BOARD_ID);
218 if (type < PSURGE_QUAD_OKEE || type > PSURGE_QUAD_ICEGRASS
219 || type != PSURGE_QUAD_IN(PSURGE_QUAD_BOARD_ID))
220 return PSURGE_DUAL;
221
222 /* looks OK, try a slightly more rigorous test */
223 /* bogus is not necessarily cacheline-aligned,
224 though I don't suppose that really matters. -- paulus */
225 for (i = 0; i < 100; i++) {
226 volatile u32 bogus[8];
227 bogus[(0+i)%8] = 0x00000000;
228 bogus[(1+i)%8] = 0x55555555;
229 bogus[(2+i)%8] = 0xFFFFFFFF;
230 bogus[(3+i)%8] = 0xAAAAAAAA;
231 bogus[(4+i)%8] = 0x33333333;
232 bogus[(5+i)%8] = 0xCCCCCCCC;
233 bogus[(6+i)%8] = 0xCCCCCCCC;
234 bogus[(7+i)%8] = 0x33333333;
235 wmb();
236 asm volatile("dcbf 0,%0" : : "r" (bogus) : "memory");
237 mb();
238 if (type != PSURGE_QUAD_IN(PSURGE_QUAD_BOARD_ID))
239 return PSURGE_DUAL;
240 }
241 return type;
242 }
243
psurge_quad_init(void)244 static void __init psurge_quad_init(void)
245 {
246 int procbits;
247
248 if (ppc_md.progress) ppc_md.progress("psurge_quad_init", 0x351);
249 procbits = ~PSURGE_QUAD_IN(PSURGE_QUAD_WHICH_CPU);
250 if (psurge_type == PSURGE_QUAD_ICEGRASS)
251 PSURGE_QUAD_BIS(PSURGE_QUAD_RESET_CTL, procbits);
252 else
253 PSURGE_QUAD_BIC(PSURGE_QUAD_CKSTOP_CTL, procbits);
254 mdelay(33);
255 out_8(psurge_sec_intr, ~0);
256 PSURGE_QUAD_OUT(PSURGE_QUAD_IRQ_CLR, procbits);
257 PSURGE_QUAD_BIS(PSURGE_QUAD_RESET_CTL, procbits);
258 if (psurge_type != PSURGE_QUAD_ICEGRASS)
259 PSURGE_QUAD_BIS(PSURGE_QUAD_CKSTOP_CTL, procbits);
260 PSURGE_QUAD_BIC(PSURGE_QUAD_PRIMARY_ARB, procbits);
261 mdelay(33);
262 PSURGE_QUAD_BIC(PSURGE_QUAD_RESET_CTL, procbits);
263 mdelay(33);
264 PSURGE_QUAD_BIS(PSURGE_QUAD_PRIMARY_ARB, procbits);
265 mdelay(33);
266 }
267
smp_psurge_probe(void)268 static void __init smp_psurge_probe(void)
269 {
270 int i, ncpus;
271 struct device_node *dn;
272
273 /*
274 * The powersurge cpu board can be used in the generation
275 * of powermacs that have a socket for an upgradeable cpu card,
276 * including the 7500, 8500, 9500, 9600.
277 * The device tree doesn't tell you if you have 2 cpus because
278 * OF doesn't know anything about the 2nd processor.
279 * Instead we look for magic bits in magic registers,
280 * in the hammerhead memory controller in the case of the
281 * dual-cpu powersurge board. -- paulus.
282 */
283 dn = of_find_node_by_name(NULL, "hammerhead");
284 if (dn == NULL)
285 return;
286 of_node_put(dn);
287
288 hhead_base = ioremap(HAMMERHEAD_BASE, 0x800);
289 quad_base = ioremap(PSURGE_QUAD_REG_ADDR, 1024);
290 psurge_sec_intr = hhead_base + HHEAD_SEC_INTR;
291
292 psurge_type = psurge_quad_probe();
293 if (psurge_type != PSURGE_DUAL) {
294 psurge_quad_init();
295 /* All released cards using this HW design have 4 CPUs */
296 ncpus = 4;
297 /* No sure how timebase sync works on those, let's use SW */
298 smp_ops->give_timebase = smp_generic_give_timebase;
299 smp_ops->take_timebase = smp_generic_take_timebase;
300 } else {
301 iounmap(quad_base);
302 if ((in_8(hhead_base + HHEAD_CONFIG) & 0x02) == 0) {
303 /* not a dual-cpu card */
304 iounmap(hhead_base);
305 psurge_type = PSURGE_NONE;
306 return;
307 }
308 ncpus = 2;
309 }
310
311 if (psurge_secondary_ipi_init())
312 return;
313
314 psurge_start = ioremap(PSURGE_START, 4);
315 psurge_pri_intr = ioremap(PSURGE_PRI_INTR, 4);
316
317 /* This is necessary because OF doesn't know about the
318 * secondary cpu(s), and thus there aren't nodes in the
319 * device tree for them, and smp_setup_cpu_maps hasn't
320 * set their bits in cpu_present_mask.
321 */
322 if (ncpus > NR_CPUS)
323 ncpus = NR_CPUS;
324 for (i = 1; i < ncpus ; ++i)
325 set_cpu_present(i, true);
326
327 if (ppc_md.progress) ppc_md.progress("smp_psurge_probe - done", 0x352);
328 }
329
smp_psurge_kick_cpu(int nr)330 static int __init smp_psurge_kick_cpu(int nr)
331 {
332 unsigned long start = __pa(__secondary_start_pmac_0) + nr * 8;
333 unsigned long a, flags;
334 int i, j;
335
336 /* Defining this here is evil ... but I prefer hiding that
337 * crap to avoid giving people ideas that they can do the
338 * same.
339 */
340 extern volatile unsigned int cpu_callin_map[NR_CPUS];
341
342 /* may need to flush here if secondary bats aren't setup */
343 for (a = KERNELBASE; a < KERNELBASE + 0x800000; a += 32)
344 asm volatile("dcbf 0,%0" : : "r" (a) : "memory");
345 asm volatile("sync");
346
347 if (ppc_md.progress) ppc_md.progress("smp_psurge_kick_cpu", 0x353);
348
349 /* This is going to freeze the timeebase, we disable interrupts */
350 local_irq_save(flags);
351
352 out_be32(psurge_start, start);
353 mb();
354
355 psurge_set_ipi(nr);
356
357 /*
358 * We can't use udelay here because the timebase is now frozen.
359 */
360 for (i = 0; i < 2000; ++i)
361 asm volatile("nop" : : : "memory");
362 psurge_clr_ipi(nr);
363
364 /*
365 * Also, because the timebase is frozen, we must not return to the
366 * caller which will try to do udelay's etc... Instead, we wait -here-
367 * for the CPU to callin.
368 */
369 for (i = 0; i < 100000 && !cpu_callin_map[nr]; ++i) {
370 for (j = 1; j < 10000; j++)
371 asm volatile("nop" : : : "memory");
372 asm volatile("sync" : : : "memory");
373 }
374 if (!cpu_callin_map[nr])
375 goto stuck;
376
377 /* And we do the TB sync here too for standard dual CPU cards */
378 if (psurge_type == PSURGE_DUAL) {
379 while(!tb_req)
380 barrier();
381 tb_req = 0;
382 mb();
383 timebase = get_tb();
384 mb();
385 while (timebase)
386 barrier();
387 mb();
388 }
389 stuck:
390 /* now interrupt the secondary, restarting both TBs */
391 if (psurge_type == PSURGE_DUAL)
392 psurge_set_ipi(1);
393
394 if (ppc_md.progress) ppc_md.progress("smp_psurge_kick_cpu - done", 0x354);
395
396 return 0;
397 }
398
smp_psurge_setup_cpu(int cpu_nr)399 static void __init smp_psurge_setup_cpu(int cpu_nr)
400 {
401 unsigned long flags = IRQF_PERCPU | IRQF_NO_THREAD;
402 int irq;
403
404 if (cpu_nr != 0 || !psurge_start)
405 return;
406
407 /* reset the entry point so if we get another intr we won't
408 * try to startup again */
409 out_be32(psurge_start, 0x100);
410 irq = irq_create_mapping(NULL, 30);
411 if (request_irq(irq, psurge_ipi_intr, flags, "primary IPI", NULL))
412 printk(KERN_ERR "Couldn't get primary IPI interrupt");
413 }
414
smp_psurge_take_timebase(void)415 void __init smp_psurge_take_timebase(void)
416 {
417 if (psurge_type != PSURGE_DUAL)
418 return;
419
420 tb_req = 1;
421 mb();
422 while (!timebase)
423 barrier();
424 mb();
425 set_tb(timebase >> 32, timebase & 0xffffffff);
426 timebase = 0;
427 mb();
428 set_dec(tb_ticks_per_jiffy/2);
429 }
430
smp_psurge_give_timebase(void)431 void __init smp_psurge_give_timebase(void)
432 {
433 /* Nothing to do here */
434 }
435
436 /* PowerSurge-style Macs */
437 struct smp_ops_t psurge_smp_ops = {
438 .message_pass = NULL, /* Use smp_muxed_ipi_message_pass */
439 .cause_ipi = smp_psurge_cause_ipi,
440 .cause_nmi_ipi = NULL,
441 .probe = smp_psurge_probe,
442 .kick_cpu = smp_psurge_kick_cpu,
443 .setup_cpu = smp_psurge_setup_cpu,
444 .give_timebase = smp_psurge_give_timebase,
445 .take_timebase = smp_psurge_take_timebase,
446 };
447 #endif /* CONFIG_PPC_PMAC32_PSURGE */
448
449 /*
450 * Core 99 and later support
451 */
452
453
smp_core99_give_timebase(void)454 static void smp_core99_give_timebase(void)
455 {
456 unsigned long flags;
457
458 local_irq_save(flags);
459
460 while(!tb_req)
461 barrier();
462 tb_req = 0;
463 (*pmac_tb_freeze)(1);
464 mb();
465 timebase = get_tb();
466 mb();
467 while (timebase)
468 barrier();
469 mb();
470 (*pmac_tb_freeze)(0);
471 mb();
472
473 local_irq_restore(flags);
474 }
475
476
smp_core99_take_timebase(void)477 static void smp_core99_take_timebase(void)
478 {
479 unsigned long flags;
480
481 local_irq_save(flags);
482
483 tb_req = 1;
484 mb();
485 while (!timebase)
486 barrier();
487 mb();
488 set_tb(timebase >> 32, timebase & 0xffffffff);
489 timebase = 0;
490 mb();
491
492 local_irq_restore(flags);
493 }
494
495 #ifdef CONFIG_PPC64
496 /*
497 * G5s enable/disable the timebase via an i2c-connected clock chip.
498 */
499 static struct pmac_i2c_bus *pmac_tb_clock_chip_host;
500 static u8 pmac_tb_pulsar_addr;
501
smp_core99_cypress_tb_freeze(int freeze)502 static void smp_core99_cypress_tb_freeze(int freeze)
503 {
504 u8 data;
505 int rc;
506
507 /* Strangely, the device-tree says address is 0xd2, but darwin
508 * accesses 0xd0 ...
509 */
510 pmac_i2c_setmode(pmac_tb_clock_chip_host,
511 pmac_i2c_mode_combined);
512 rc = pmac_i2c_xfer(pmac_tb_clock_chip_host,
513 0xd0 | pmac_i2c_read,
514 1, 0x81, &data, 1);
515 if (rc != 0)
516 goto bail;
517
518 data = (data & 0xf3) | (freeze ? 0x00 : 0x0c);
519
520 pmac_i2c_setmode(pmac_tb_clock_chip_host, pmac_i2c_mode_stdsub);
521 rc = pmac_i2c_xfer(pmac_tb_clock_chip_host,
522 0xd0 | pmac_i2c_write,
523 1, 0x81, &data, 1);
524
525 bail:
526 if (rc != 0) {
527 printk("Cypress Timebase %s rc: %d\n",
528 freeze ? "freeze" : "unfreeze", rc);
529 panic("Timebase freeze failed !\n");
530 }
531 }
532
533
smp_core99_pulsar_tb_freeze(int freeze)534 static void smp_core99_pulsar_tb_freeze(int freeze)
535 {
536 u8 data;
537 int rc;
538
539 pmac_i2c_setmode(pmac_tb_clock_chip_host,
540 pmac_i2c_mode_combined);
541 rc = pmac_i2c_xfer(pmac_tb_clock_chip_host,
542 pmac_tb_pulsar_addr | pmac_i2c_read,
543 1, 0x2e, &data, 1);
544 if (rc != 0)
545 goto bail;
546
547 data = (data & 0x88) | (freeze ? 0x11 : 0x22);
548
549 pmac_i2c_setmode(pmac_tb_clock_chip_host, pmac_i2c_mode_stdsub);
550 rc = pmac_i2c_xfer(pmac_tb_clock_chip_host,
551 pmac_tb_pulsar_addr | pmac_i2c_write,
552 1, 0x2e, &data, 1);
553 bail:
554 if (rc != 0) {
555 printk(KERN_ERR "Pulsar Timebase %s rc: %d\n",
556 freeze ? "freeze" : "unfreeze", rc);
557 panic("Timebase freeze failed !\n");
558 }
559 }
560
smp_core99_setup_i2c_hwsync(int ncpus)561 static void __init smp_core99_setup_i2c_hwsync(int ncpus)
562 {
563 struct device_node *cc = NULL;
564 struct device_node *p;
565 const char *name = NULL;
566 const u32 *reg;
567 int ok;
568
569 /* Look for the clock chip */
570 for_each_node_by_name(cc, "i2c-hwclock") {
571 p = of_get_parent(cc);
572 ok = p && of_device_is_compatible(p, "uni-n-i2c");
573 of_node_put(p);
574 if (!ok)
575 continue;
576
577 pmac_tb_clock_chip_host = pmac_i2c_find_bus(cc);
578 if (pmac_tb_clock_chip_host == NULL)
579 continue;
580 reg = of_get_property(cc, "reg", NULL);
581 if (reg == NULL)
582 continue;
583 switch (*reg) {
584 case 0xd2:
585 if (of_device_is_compatible(cc,"pulsar-legacy-slewing")) {
586 pmac_tb_freeze = smp_core99_pulsar_tb_freeze;
587 pmac_tb_pulsar_addr = 0xd2;
588 name = "Pulsar";
589 } else if (of_device_is_compatible(cc, "cy28508")) {
590 pmac_tb_freeze = smp_core99_cypress_tb_freeze;
591 name = "Cypress";
592 }
593 break;
594 case 0xd4:
595 pmac_tb_freeze = smp_core99_pulsar_tb_freeze;
596 pmac_tb_pulsar_addr = 0xd4;
597 name = "Pulsar";
598 break;
599 }
600 if (pmac_tb_freeze != NULL)
601 break;
602 }
603 if (pmac_tb_freeze != NULL) {
604 /* Open i2c bus for synchronous access */
605 if (pmac_i2c_open(pmac_tb_clock_chip_host, 1)) {
606 printk(KERN_ERR "Failed top open i2c bus for clock"
607 " sync, fallback to software sync !\n");
608 goto no_i2c_sync;
609 }
610 printk(KERN_INFO "Processor timebase sync using %s i2c clock\n",
611 name);
612 return;
613 }
614 no_i2c_sync:
615 pmac_tb_freeze = NULL;
616 pmac_tb_clock_chip_host = NULL;
617 }
618
619
620
621 /*
622 * Newer G5s uses a platform function
623 */
624
smp_core99_pfunc_tb_freeze(int freeze)625 static void smp_core99_pfunc_tb_freeze(int freeze)
626 {
627 struct device_node *cpus;
628 struct pmf_args args;
629
630 cpus = of_find_node_by_path("/cpus");
631 BUG_ON(cpus == NULL);
632 args.count = 1;
633 args.u[0].v = !freeze;
634 pmf_call_function(cpus, "cpu-timebase", &args);
635 of_node_put(cpus);
636 }
637
638 #else /* CONFIG_PPC64 */
639
640 /*
641 * SMP G4 use a GPIO to enable/disable the timebase.
642 */
643
644 static unsigned int core99_tb_gpio; /* Timebase freeze GPIO */
645
smp_core99_gpio_tb_freeze(int freeze)646 static void smp_core99_gpio_tb_freeze(int freeze)
647 {
648 if (freeze)
649 pmac_call_feature(PMAC_FTR_WRITE_GPIO, NULL, core99_tb_gpio, 4);
650 else
651 pmac_call_feature(PMAC_FTR_WRITE_GPIO, NULL, core99_tb_gpio, 0);
652 pmac_call_feature(PMAC_FTR_READ_GPIO, NULL, core99_tb_gpio, 0);
653 }
654
655
656 #endif /* !CONFIG_PPC64 */
657
core99_init_caches(int cpu)658 static void core99_init_caches(int cpu)
659 {
660 #ifndef CONFIG_PPC64
661 /* L2 and L3 cache settings to pass from CPU0 to CPU1 on G4 cpus */
662 static long int core99_l2_cache;
663 static long int core99_l3_cache;
664
665 if (!cpu_has_feature(CPU_FTR_L2CR))
666 return;
667
668 if (cpu == 0) {
669 core99_l2_cache = _get_L2CR();
670 printk("CPU0: L2CR is %lx\n", core99_l2_cache);
671 } else {
672 printk("CPU%d: L2CR was %lx\n", cpu, _get_L2CR());
673 _set_L2CR(0);
674 _set_L2CR(core99_l2_cache);
675 printk("CPU%d: L2CR set to %lx\n", cpu, core99_l2_cache);
676 }
677
678 if (!cpu_has_feature(CPU_FTR_L3CR))
679 return;
680
681 if (cpu == 0){
682 core99_l3_cache = _get_L3CR();
683 printk("CPU0: L3CR is %lx\n", core99_l3_cache);
684 } else {
685 printk("CPU%d: L3CR was %lx\n", cpu, _get_L3CR());
686 _set_L3CR(0);
687 _set_L3CR(core99_l3_cache);
688 printk("CPU%d: L3CR set to %lx\n", cpu, core99_l3_cache);
689 }
690 #endif /* !CONFIG_PPC64 */
691 }
692
smp_core99_setup(int ncpus)693 static void __init smp_core99_setup(int ncpus)
694 {
695 #ifdef CONFIG_PPC64
696
697 /* i2c based HW sync on some G5s */
698 if (of_machine_is_compatible("PowerMac7,2") ||
699 of_machine_is_compatible("PowerMac7,3") ||
700 of_machine_is_compatible("RackMac3,1"))
701 smp_core99_setup_i2c_hwsync(ncpus);
702
703 /* pfunc based HW sync on recent G5s */
704 if (pmac_tb_freeze == NULL) {
705 struct device_node *cpus =
706 of_find_node_by_path("/cpus");
707 if (cpus &&
708 of_get_property(cpus, "platform-cpu-timebase", NULL)) {
709 pmac_tb_freeze = smp_core99_pfunc_tb_freeze;
710 printk(KERN_INFO "Processor timebase sync using"
711 " platform function\n");
712 }
713 }
714
715 #else /* CONFIG_PPC64 */
716
717 /* GPIO based HW sync on ppc32 Core99 */
718 if (pmac_tb_freeze == NULL && !of_machine_is_compatible("MacRISC4")) {
719 struct device_node *cpu;
720 const u32 *tbprop = NULL;
721
722 core99_tb_gpio = KL_GPIO_TB_ENABLE; /* default value */
723 cpu = of_find_node_by_type(NULL, "cpu");
724 if (cpu != NULL) {
725 tbprop = of_get_property(cpu, "timebase-enable", NULL);
726 if (tbprop)
727 core99_tb_gpio = *tbprop;
728 of_node_put(cpu);
729 }
730 pmac_tb_freeze = smp_core99_gpio_tb_freeze;
731 printk(KERN_INFO "Processor timebase sync using"
732 " GPIO 0x%02x\n", core99_tb_gpio);
733 }
734
735 #endif /* CONFIG_PPC64 */
736
737 /* No timebase sync, fallback to software */
738 if (pmac_tb_freeze == NULL) {
739 smp_ops->give_timebase = smp_generic_give_timebase;
740 smp_ops->take_timebase = smp_generic_take_timebase;
741 printk(KERN_INFO "Processor timebase sync using software\n");
742 }
743
744 #ifndef CONFIG_PPC64
745 {
746 int i;
747
748 /* XXX should get this from reg properties */
749 for (i = 1; i < ncpus; ++i)
750 set_hard_smp_processor_id(i, i);
751 }
752 #endif
753
754 /* 32 bits SMP can't NAP */
755 if (!of_machine_is_compatible("MacRISC4"))
756 powersave_nap = 0;
757 }
758
smp_core99_probe(void)759 static void __init smp_core99_probe(void)
760 {
761 struct device_node *cpus;
762 int ncpus = 0;
763
764 if (ppc_md.progress) ppc_md.progress("smp_core99_probe", 0x345);
765
766 /* Count CPUs in the device-tree */
767 for_each_node_by_type(cpus, "cpu")
768 ++ncpus;
769
770 printk(KERN_INFO "PowerMac SMP probe found %d cpus\n", ncpus);
771
772 /* Nothing more to do if less than 2 of them */
773 if (ncpus <= 1)
774 return;
775
776 /* We need to perform some early initialisations before we can start
777 * setting up SMP as we are running before initcalls
778 */
779 pmac_pfunc_base_install();
780 pmac_i2c_init();
781
782 /* Setup various bits like timebase sync method, ability to nap, ... */
783 smp_core99_setup(ncpus);
784
785 /* Install IPIs */
786 mpic_request_ipis();
787
788 /* Collect l2cr and l3cr values from CPU 0 */
789 core99_init_caches(0);
790 }
791
smp_core99_kick_cpu(int nr)792 static int smp_core99_kick_cpu(int nr)
793 {
794 unsigned int save_vector;
795 unsigned long target, flags;
796 unsigned int *vector = (unsigned int *)(PAGE_OFFSET+0x100);
797
798 if (nr < 0 || nr > 3)
799 return -ENOENT;
800
801 if (ppc_md.progress)
802 ppc_md.progress("smp_core99_kick_cpu", 0x346);
803
804 local_irq_save(flags);
805
806 /* Save reset vector */
807 save_vector = *vector;
808
809 /* Setup fake reset vector that does
810 * b __secondary_start_pmac_0 + nr*8
811 */
812 target = (unsigned long) __secondary_start_pmac_0 + nr * 8;
813 patch_branch((struct ppc_inst *)vector, target, BRANCH_SET_LINK);
814
815 /* Put some life in our friend */
816 pmac_call_feature(PMAC_FTR_RESET_CPU, NULL, nr, 0);
817
818 /* FIXME: We wait a bit for the CPU to take the exception, I should
819 * instead wait for the entry code to set something for me. Well,
820 * ideally, all that crap will be done in prom.c and the CPU left
821 * in a RAM-based wait loop like CHRP.
822 */
823 mdelay(1);
824
825 /* Restore our exception vector */
826 patch_instruction((struct ppc_inst *)vector, ppc_inst(save_vector));
827
828 local_irq_restore(flags);
829 if (ppc_md.progress) ppc_md.progress("smp_core99_kick_cpu done", 0x347);
830
831 return 0;
832 }
833
smp_core99_setup_cpu(int cpu_nr)834 static void smp_core99_setup_cpu(int cpu_nr)
835 {
836 /* Setup L2/L3 */
837 if (cpu_nr != 0)
838 core99_init_caches(cpu_nr);
839
840 /* Setup openpic */
841 mpic_setup_this_cpu();
842 }
843
844 #ifdef CONFIG_PPC64
845 #ifdef CONFIG_HOTPLUG_CPU
846 static unsigned int smp_core99_host_open;
847
smp_core99_cpu_prepare(unsigned int cpu)848 static int smp_core99_cpu_prepare(unsigned int cpu)
849 {
850 int rc;
851
852 /* Open i2c bus if it was used for tb sync */
853 if (pmac_tb_clock_chip_host && !smp_core99_host_open) {
854 rc = pmac_i2c_open(pmac_tb_clock_chip_host, 1);
855 if (rc) {
856 pr_err("Failed to open i2c bus for time sync\n");
857 return notifier_from_errno(rc);
858 }
859 smp_core99_host_open = 1;
860 }
861 return 0;
862 }
863
smp_core99_cpu_online(unsigned int cpu)864 static int smp_core99_cpu_online(unsigned int cpu)
865 {
866 /* Close i2c bus if it was used for tb sync */
867 if (pmac_tb_clock_chip_host && smp_core99_host_open) {
868 pmac_i2c_close(pmac_tb_clock_chip_host);
869 smp_core99_host_open = 0;
870 }
871 return 0;
872 }
873 #endif /* CONFIG_HOTPLUG_CPU */
874
smp_core99_bringup_done(void)875 static void __init smp_core99_bringup_done(void)
876 {
877 extern void g5_phy_disable_cpu1(void);
878
879 /* Close i2c bus if it was used for tb sync */
880 if (pmac_tb_clock_chip_host)
881 pmac_i2c_close(pmac_tb_clock_chip_host);
882
883 /* If we didn't start the second CPU, we must take
884 * it off the bus.
885 */
886 if (of_machine_is_compatible("MacRISC4") &&
887 num_online_cpus() < 2) {
888 set_cpu_present(1, false);
889 g5_phy_disable_cpu1();
890 }
891 #ifdef CONFIG_HOTPLUG_CPU
892 cpuhp_setup_state_nocalls(CPUHP_POWERPC_PMAC_PREPARE,
893 "powerpc/pmac:prepare", smp_core99_cpu_prepare,
894 NULL);
895 cpuhp_setup_state_nocalls(CPUHP_AP_ONLINE_DYN, "powerpc/pmac:online",
896 smp_core99_cpu_online, NULL);
897 #endif
898
899 if (ppc_md.progress)
900 ppc_md.progress("smp_core99_bringup_done", 0x349);
901 }
902 #endif /* CONFIG_PPC64 */
903
904 #ifdef CONFIG_HOTPLUG_CPU
905
smp_core99_cpu_disable(void)906 static int smp_core99_cpu_disable(void)
907 {
908 int rc = generic_cpu_disable();
909 if (rc)
910 return rc;
911
912 mpic_cpu_set_priority(0xf);
913
914 cleanup_cpu_mmu_context();
915
916 return 0;
917 }
918
919 #ifdef CONFIG_PPC32
920
pmac_cpu_offline_self(void)921 static void pmac_cpu_offline_self(void)
922 {
923 int cpu = smp_processor_id();
924
925 local_irq_disable();
926 idle_task_exit();
927 pr_debug("CPU%d offline\n", cpu);
928 generic_set_cpu_dead(cpu);
929 smp_wmb();
930 mb();
931 low_cpu_offline_self();
932 }
933
934 #else /* CONFIG_PPC32 */
935
pmac_cpu_offline_self(void)936 static void pmac_cpu_offline_self(void)
937 {
938 int cpu = smp_processor_id();
939
940 local_irq_disable();
941 idle_task_exit();
942
943 /*
944 * turn off as much as possible, we'll be
945 * kicked out as this will only be invoked
946 * on core99 platforms for now ...
947 */
948
949 printk(KERN_INFO "CPU#%d offline\n", cpu);
950 generic_set_cpu_dead(cpu);
951 smp_wmb();
952
953 /*
954 * Re-enable interrupts. The NAP code needs to enable them
955 * anyways, do it now so we deal with the case where one already
956 * happened while soft-disabled.
957 * We shouldn't get any external interrupts, only decrementer, and the
958 * decrementer handler is safe for use on offline CPUs
959 */
960 local_irq_enable();
961
962 while (1) {
963 /* let's not take timer interrupts too often ... */
964 set_dec(0x7fffffff);
965
966 /* Enter NAP mode */
967 power4_idle();
968 }
969 }
970
971 #endif /* else CONFIG_PPC32 */
972 #endif /* CONFIG_HOTPLUG_CPU */
973
974 /* Core99 Macs (dual G4s and G5s) */
975 static struct smp_ops_t core99_smp_ops = {
976 .message_pass = smp_mpic_message_pass,
977 .probe = smp_core99_probe,
978 #ifdef CONFIG_PPC64
979 .bringup_done = smp_core99_bringup_done,
980 #endif
981 .kick_cpu = smp_core99_kick_cpu,
982 .setup_cpu = smp_core99_setup_cpu,
983 .give_timebase = smp_core99_give_timebase,
984 .take_timebase = smp_core99_take_timebase,
985 #if defined(CONFIG_HOTPLUG_CPU)
986 .cpu_disable = smp_core99_cpu_disable,
987 .cpu_die = generic_cpu_die,
988 #endif
989 };
990
pmac_setup_smp(void)991 void __init pmac_setup_smp(void)
992 {
993 struct device_node *np;
994
995 /* Check for Core99 */
996 np = of_find_node_by_name(NULL, "uni-n");
997 if (!np)
998 np = of_find_node_by_name(NULL, "u3");
999 if (!np)
1000 np = of_find_node_by_name(NULL, "u4");
1001 if (np) {
1002 of_node_put(np);
1003 smp_ops = &core99_smp_ops;
1004 }
1005 #ifdef CONFIG_PPC_PMAC32_PSURGE
1006 else {
1007 /* We have to set bits in cpu_possible_mask here since the
1008 * secondary CPU(s) aren't in the device tree. Various
1009 * things won't be initialized for CPUs not in the possible
1010 * map, so we really need to fix it up here.
1011 */
1012 int cpu;
1013
1014 for (cpu = 1; cpu < 4 && cpu < NR_CPUS; ++cpu)
1015 set_cpu_possible(cpu, true);
1016 smp_ops = &psurge_smp_ops;
1017 }
1018 #endif /* CONFIG_PPC_PMAC32_PSURGE */
1019
1020 #ifdef CONFIG_HOTPLUG_CPU
1021 smp_ops->cpu_offline_self = pmac_cpu_offline_self;
1022 #endif
1023 }
1024
1025
1026
