1 /*
2 *
3 * Copyright (c) 2012 Gilles Dartiguelongue, Thomas Richter
4 *
5 * All Rights Reserved.
6 *
7 * Permission is hereby granted, free of charge, to any person obtaining a
8 * copy of this software and associated documentation files (the
9 * "Software"), to deal in the Software without restriction, including
10 * without limitation the rights to use, copy, modify, merge, publish,
11 * distribute, sub license, and/or sell copies of the Software, and to
12 * permit persons to whom the Software is furnished to do so, subject to
13 * the following conditions:
14 *
15 * The above copyright notice and this permission notice (including the
16 * next paragraph) shall be included in all copies or substantial portions
17 * of the Software.
18 *
19 * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS
20 * OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
21 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.
22 * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
23 * ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT,
24 * TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE
25 * SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
26 *
27 */
28
29 #include "dvo.h"
30 #include "i915_reg.h"
31 #include "i915_drv.h"
32
33 #define NS2501_VID 0x1305
34 #define NS2501_DID 0x6726
35
36 #define NS2501_VID_LO 0x00
37 #define NS2501_VID_HI 0x01
38 #define NS2501_DID_LO 0x02
39 #define NS2501_DID_HI 0x03
40 #define NS2501_REV 0x04
41 #define NS2501_RSVD 0x05
42 #define NS2501_FREQ_LO 0x06
43 #define NS2501_FREQ_HI 0x07
44
45 #define NS2501_REG8 0x08
46 #define NS2501_8_VEN (1<<5)
47 #define NS2501_8_HEN (1<<4)
48 #define NS2501_8_DSEL (1<<3)
49 #define NS2501_8_BPAS (1<<2)
50 #define NS2501_8_RSVD (1<<1)
51 #define NS2501_8_PD (1<<0)
52
53 #define NS2501_REG9 0x09
54 #define NS2501_9_VLOW (1<<7)
55 #define NS2501_9_MSEL_MASK (0x7<<4)
56 #define NS2501_9_TSEL (1<<3)
57 #define NS2501_9_RSEN (1<<2)
58 #define NS2501_9_RSVD (1<<1)
59 #define NS2501_9_MDI (1<<0)
60
61 #define NS2501_REGC 0x0c
62
63 /*
64 * The following registers are not part of the official datasheet
65 * and are the result of reverse engineering.
66 */
67
68 /*
69 * Register c0 controls how the DVO synchronizes with
70 * its input.
71 */
72 #define NS2501_REGC0 0xc0
73 #define NS2501_C0_ENABLE (1<<0) /* enable the DVO sync in general */
74 #define NS2501_C0_HSYNC (1<<1) /* synchronize horizontal with input */
75 #define NS2501_C0_VSYNC (1<<2) /* synchronize vertical with input */
76 #define NS2501_C0_RESET (1<<7) /* reset the synchronization flip/flops */
77
78 /*
79 * Register 41 is somehow related to the sync register and sync
80 * configuration. It should be 0x32 whenever regC0 is 0x05 (hsync off)
81 * and 0x00 otherwise.
82 */
83 #define NS2501_REG41 0x41
84
85 /*
86 * this register controls the dithering of the DVO
87 * One bit enables it, the other define the dithering depth.
88 * The higher the value, the lower the dithering depth.
89 */
90 #define NS2501_F9_REG 0xf9
91 #define NS2501_F9_ENABLE (1<<0) /* if set, dithering is enabled */
92 #define NS2501_F9_DITHER_MASK (0x7f<<1) /* controls the dither depth */
93 #define NS2501_F9_DITHER_SHIFT 1 /* shifts the dither mask */
94
95 /*
96 * PLL configuration register. This is a pair of registers,
97 * one single byte register at 1B, and a pair at 1C,1D.
98 * These registers are counters/dividers.
99 */
100 #define NS2501_REG1B 0x1b /* one byte PLL control register */
101 #define NS2501_REG1C 0x1c /* low-part of the second register */
102 #define NS2501_REG1D 0x1d /* high-part of the second register */
103
104 /*
105 * Scaler control registers. Horizontal at b8,b9,
106 * vertical at 10,11. The scale factor is computed as
107 * 2^16/control-value. The low-byte comes first.
108 */
109 #define NS2501_REG10 0x10 /* low-byte vertical scaler */
110 #define NS2501_REG11 0x11 /* high-byte vertical scaler */
111 #define NS2501_REGB8 0xb8 /* low-byte horizontal scaler */
112 #define NS2501_REGB9 0xb9 /* high-byte horizontal scaler */
113
114 /*
115 * Display window definition. This consists of four registers
116 * per dimension. One register pair defines the start of the
117 * display, one the end.
118 * As far as I understand, this defines the window within which
119 * the scaler samples the input.
120 */
121 #define NS2501_REGC1 0xc1 /* low-byte horizontal display start */
122 #define NS2501_REGC2 0xc2 /* high-byte horizontal display start */
123 #define NS2501_REGC3 0xc3 /* low-byte horizontal display stop */
124 #define NS2501_REGC4 0xc4 /* high-byte horizontal display stop */
125 #define NS2501_REGC5 0xc5 /* low-byte vertical display start */
126 #define NS2501_REGC6 0xc6 /* high-byte vertical display start */
127 #define NS2501_REGC7 0xc7 /* low-byte vertical display stop */
128 #define NS2501_REGC8 0xc8 /* high-byte vertical display stop */
129
130 /*
131 * The following register pair seems to define the start of
132 * the vertical sync. If automatic syncing is enabled, and the
133 * register value defines a sync pulse that is later than the
134 * incoming sync, then the register value is ignored and the
135 * external hsync triggers the synchronization.
136 */
137 #define NS2501_REG80 0x80 /* low-byte vsync-start */
138 #define NS2501_REG81 0x81 /* high-byte vsync-start */
139
140 /*
141 * The following register pair seems to define the total number
142 * of lines created at the output side of the scaler.
143 * This is again a low-high register pair.
144 */
145 #define NS2501_REG82 0x82 /* output display height, low byte */
146 #define NS2501_REG83 0x83 /* output display height, high byte */
147
148 /*
149 * The following registers define the end of the front-porch
150 * in horizontal and vertical position and hence allow to shift
151 * the image left/right or up/down.
152 */
153 #define NS2501_REG98 0x98 /* horizontal start of display + 256, low */
154 #define NS2501_REG99 0x99 /* horizontal start of display + 256, high */
155 #define NS2501_REG8E 0x8e /* vertical start of the display, low byte */
156 #define NS2501_REG8F 0x8f /* vertical start of the display, high byte */
157
158 /*
159 * The following register pair control the function of the
160 * backlight and the DVO output. To enable the corresponding
161 * function, the corresponding bit must be set in both registers.
162 */
163 #define NS2501_REG34 0x34 /* DVO enable functions, first register */
164 #define NS2501_REG35 0x35 /* DVO enable functions, second register */
165 #define NS2501_34_ENABLE_OUTPUT (1<<0) /* enable DVO output */
166 #define NS2501_34_ENABLE_BACKLIGHT (1<<1) /* enable backlight */
167
168 /*
169 * Registers 9C and 9D define the vertical output offset
170 * of the visible region.
171 */
172 #define NS2501_REG9C 0x9c
173 #define NS2501_REG9D 0x9d
174
175 /*
176 * The register 9F defines the dithering. This requires the
177 * scaler to be ON. Bit 0 enables dithering, the remaining
178 * bits control the depth of the dither. The higher the value,
179 * the LOWER the dithering amplitude. A good value seems to be
180 * 15 (total register value).
181 */
182 #define NS2501_REGF9 0xf9
183 #define NS2501_F9_ENABLE_DITHER (1<<0) /* enable dithering */
184 #define NS2501_F9_DITHER_MASK (0x7f<<1) /* dither masking */
185 #define NS2501_F9_DITHER_SHIFT 1 /* upshift of the dither mask */
186
187 enum {
188 MODE_640x480,
189 MODE_800x600,
190 MODE_1024x768,
191 };
192
193 struct ns2501_reg {
194 u8 offset;
195 u8 value;
196 };
197
198 /*
199 * The following structure keeps the complete configuration of
200 * the DVO, given a specific output configuration.
201 * This is pretty much guess-work from reverse-engineering, so
202 * read all this with a grain of salt.
203 */
204 struct ns2501_configuration {
205 u8 sync; /* configuration of the C0 register */
206 u8 conf; /* configuration register 8 */
207 u8 syncb; /* configuration register 41 */
208 u8 dither; /* configuration of the dithering */
209 u8 pll_a; /* PLL configuration, register A, 1B */
210 u16 pll_b; /* PLL configuration, register B, 1C/1D */
211 u16 hstart; /* horizontal start, registers C1/C2 */
212 u16 hstop; /* horizontal total, registers C3/C4 */
213 u16 vstart; /* vertical start, registers C5/C6 */
214 u16 vstop; /* vertical total, registers C7/C8 */
215 u16 vsync; /* manual vertical sync start, 80/81 */
216 u16 vtotal; /* number of lines generated, 82/83 */
217 u16 hpos; /* horizontal position + 256, 98/99 */
218 u16 vpos; /* vertical position, 8e/8f */
219 u16 voffs; /* vertical output offset, 9c/9d */
220 u16 hscale; /* horizontal scaling factor, b8/b9 */
221 u16 vscale; /* vertical scaling factor, 10/11 */
222 };
223
224 /*
225 * DVO configuration values, partially based on what the BIOS
226 * of the Fujitsu Lifebook S6010 writes into registers,
227 * partially found by manual tweaking. These configurations assume
228 * a 1024x768 panel.
229 */
230 static const struct ns2501_configuration ns2501_modes[] = {
231 [MODE_640x480] = {
232 .sync = NS2501_C0_ENABLE | NS2501_C0_VSYNC,
233 .conf = NS2501_8_VEN | NS2501_8_HEN | NS2501_8_PD,
234 .syncb = 0x32,
235 .dither = 0x0f,
236 .pll_a = 17,
237 .pll_b = 852,
238 .hstart = 144,
239 .hstop = 783,
240 .vstart = 22,
241 .vstop = 514,
242 .vsync = 2047, /* actually, ignored with this config */
243 .vtotal = 1341,
244 .hpos = 0,
245 .vpos = 16,
246 .voffs = 36,
247 .hscale = 40960,
248 .vscale = 40960
249 },
250 [MODE_800x600] = {
251 .sync = NS2501_C0_ENABLE |
252 NS2501_C0_HSYNC | NS2501_C0_VSYNC,
253 .conf = NS2501_8_VEN | NS2501_8_HEN | NS2501_8_PD,
254 .syncb = 0x00,
255 .dither = 0x0f,
256 .pll_a = 25,
257 .pll_b = 612,
258 .hstart = 215,
259 .hstop = 1016,
260 .vstart = 26,
261 .vstop = 627,
262 .vsync = 807,
263 .vtotal = 1341,
264 .hpos = 0,
265 .vpos = 4,
266 .voffs = 35,
267 .hscale = 51248,
268 .vscale = 51232
269 },
270 [MODE_1024x768] = {
271 .sync = NS2501_C0_ENABLE | NS2501_C0_VSYNC,
272 .conf = NS2501_8_VEN | NS2501_8_HEN | NS2501_8_PD,
273 .syncb = 0x32,
274 .dither = 0x0f,
275 .pll_a = 11,
276 .pll_b = 1350,
277 .hstart = 276,
278 .hstop = 1299,
279 .vstart = 15,
280 .vstop = 1056,
281 .vsync = 2047,
282 .vtotal = 1341,
283 .hpos = 0,
284 .vpos = 7,
285 .voffs = 27,
286 .hscale = 65535,
287 .vscale = 65535
288 }
289 };
290
291 /*
292 * Other configuration values left by the BIOS of the
293 * Fujitsu S6010 in the DVO control registers. Their
294 * value does not depend on the BIOS and their meaning
295 * is unknown.
296 */
297
298 static const struct ns2501_reg mode_agnostic_values[] = {
299 /* 08 is mode specific */
300 [0] = { .offset = 0x0a, .value = 0x81, },
301 /* 10,11 are part of the mode specific configuration */
302 [1] = { .offset = 0x12, .value = 0x02, },
303 [2] = { .offset = 0x18, .value = 0x07, },
304 [3] = { .offset = 0x19, .value = 0x00, },
305 [4] = { .offset = 0x1a, .value = 0x00, }, /* PLL?, ignored */
306 /* 1b,1c,1d are part of the mode specific configuration */
307 [5] = { .offset = 0x1e, .value = 0x02, },
308 [6] = { .offset = 0x1f, .value = 0x40, },
309 [7] = { .offset = 0x20, .value = 0x00, },
310 [8] = { .offset = 0x21, .value = 0x00, },
311 [9] = { .offset = 0x22, .value = 0x00, },
312 [10] = { .offset = 0x23, .value = 0x00, },
313 [11] = { .offset = 0x24, .value = 0x00, },
314 [12] = { .offset = 0x25, .value = 0x00, },
315 [13] = { .offset = 0x26, .value = 0x00, },
316 [14] = { .offset = 0x27, .value = 0x00, },
317 [15] = { .offset = 0x7e, .value = 0x18, },
318 /* 80-84 are part of the mode-specific configuration */
319 [16] = { .offset = 0x84, .value = 0x00, },
320 [17] = { .offset = 0x85, .value = 0x00, },
321 [18] = { .offset = 0x86, .value = 0x00, },
322 [19] = { .offset = 0x87, .value = 0x00, },
323 [20] = { .offset = 0x88, .value = 0x00, },
324 [21] = { .offset = 0x89, .value = 0x00, },
325 [22] = { .offset = 0x8a, .value = 0x00, },
326 [23] = { .offset = 0x8b, .value = 0x00, },
327 [24] = { .offset = 0x8c, .value = 0x10, },
328 [25] = { .offset = 0x8d, .value = 0x02, },
329 /* 8e,8f are part of the mode-specific configuration */
330 [26] = { .offset = 0x90, .value = 0xff, },
331 [27] = { .offset = 0x91, .value = 0x07, },
332 [28] = { .offset = 0x92, .value = 0xa0, },
333 [29] = { .offset = 0x93, .value = 0x02, },
334 [30] = { .offset = 0x94, .value = 0x00, },
335 [31] = { .offset = 0x95, .value = 0x00, },
336 [32] = { .offset = 0x96, .value = 0x05, },
337 [33] = { .offset = 0x97, .value = 0x00, },
338 /* 98,99 are part of the mode-specific configuration */
339 [34] = { .offset = 0x9a, .value = 0x88, },
340 [35] = { .offset = 0x9b, .value = 0x00, },
341 /* 9c,9d are part of the mode-specific configuration */
342 [36] = { .offset = 0x9e, .value = 0x25, },
343 [37] = { .offset = 0x9f, .value = 0x03, },
344 [38] = { .offset = 0xa0, .value = 0x28, },
345 [39] = { .offset = 0xa1, .value = 0x01, },
346 [40] = { .offset = 0xa2, .value = 0x28, },
347 [41] = { .offset = 0xa3, .value = 0x05, },
348 /* register 0xa4 is mode specific, but 0x80..0x84 works always */
349 [42] = { .offset = 0xa4, .value = 0x84, },
350 [43] = { .offset = 0xa5, .value = 0x00, },
351 [44] = { .offset = 0xa6, .value = 0x00, },
352 [45] = { .offset = 0xa7, .value = 0x00, },
353 [46] = { .offset = 0xa8, .value = 0x00, },
354 /* 0xa9 to 0xab are mode specific, but have no visible effect */
355 [47] = { .offset = 0xa9, .value = 0x04, },
356 [48] = { .offset = 0xaa, .value = 0x70, },
357 [49] = { .offset = 0xab, .value = 0x4f, },
358 [50] = { .offset = 0xac, .value = 0x00, },
359 [51] = { .offset = 0xad, .value = 0x00, },
360 [52] = { .offset = 0xb6, .value = 0x09, },
361 [53] = { .offset = 0xb7, .value = 0x03, },
362 /* b8,b9 are part of the mode-specific configuration */
363 [54] = { .offset = 0xba, .value = 0x00, },
364 [55] = { .offset = 0xbb, .value = 0x20, },
365 [56] = { .offset = 0xf3, .value = 0x90, },
366 [57] = { .offset = 0xf4, .value = 0x00, },
367 [58] = { .offset = 0xf7, .value = 0x88, },
368 /* f8 is mode specific, but the value does not matter */
369 [59] = { .offset = 0xf8, .value = 0x0a, },
370 [60] = { .offset = 0xf9, .value = 0x00, }
371 };
372
373 static const struct ns2501_reg regs_init[] = {
374 [0] = { .offset = 0x35, .value = 0xff, },
375 [1] = { .offset = 0x34, .value = 0x00, },
376 [2] = { .offset = 0x08, .value = 0x30, },
377 };
378
379 struct ns2501_priv {
380 bool quiet;
381 const struct ns2501_configuration *conf;
382 };
383
384 #define NSPTR(d) ((NS2501Ptr)(d->DriverPrivate.ptr))
385
386 /*
387 ** Read a register from the ns2501.
388 ** Returns true if successful, false otherwise.
389 ** If it returns false, it might be wise to enable the
390 ** DVO with the above function.
391 */
ns2501_readb(struct intel_dvo_device * dvo,int addr,u8 * ch)392 static bool ns2501_readb(struct intel_dvo_device *dvo, int addr, u8 *ch)
393 {
394 struct ns2501_priv *ns = dvo->dev_priv;
395 struct i2c_adapter *adapter = dvo->i2c_bus;
396 u8 out_buf[2];
397 u8 in_buf[2];
398
399 struct i2c_msg msgs[] = {
400 {
401 .addr = dvo->slave_addr,
402 .flags = 0,
403 .len = 1,
404 .buf = out_buf,
405 },
406 {
407 .addr = dvo->slave_addr,
408 .flags = I2C_M_RD,
409 .len = 1,
410 .buf = in_buf,
411 }
412 };
413
414 out_buf[0] = addr;
415 out_buf[1] = 0;
416
417 if (i2c_transfer(adapter, msgs, 2) == 2) {
418 *ch = in_buf[0];
419 return true;
420 }
421
422 if (!ns->quiet) {
423 DRM_DEBUG_KMS
424 ("Unable to read register 0x%02x from %s:0x%02x.\n", addr,
425 adapter->name, dvo->slave_addr);
426 }
427
428 return false;
429 }
430
431 /*
432 ** Write a register to the ns2501.
433 ** Returns true if successful, false otherwise.
434 ** If it returns false, it might be wise to enable the
435 ** DVO with the above function.
436 */
ns2501_writeb(struct intel_dvo_device * dvo,int addr,u8 ch)437 static bool ns2501_writeb(struct intel_dvo_device *dvo, int addr, u8 ch)
438 {
439 struct ns2501_priv *ns = dvo->dev_priv;
440 struct i2c_adapter *adapter = dvo->i2c_bus;
441 u8 out_buf[2];
442
443 struct i2c_msg msg = {
444 .addr = dvo->slave_addr,
445 .flags = 0,
446 .len = 2,
447 .buf = out_buf,
448 };
449
450 out_buf[0] = addr;
451 out_buf[1] = ch;
452
453 if (i2c_transfer(adapter, &msg, 1) == 1) {
454 return true;
455 }
456
457 if (!ns->quiet) {
458 DRM_DEBUG_KMS("Unable to write register 0x%02x to %s:%d\n",
459 addr, adapter->name, dvo->slave_addr);
460 }
461
462 return false;
463 }
464
465 /* National Semiconductor 2501 driver for chip on i2c bus
466 * scan for the chip on the bus.
467 * Hope the VBIOS initialized the PLL correctly so we can
468 * talk to it. If not, it will not be seen and not detected.
469 * Bummer!
470 */
ns2501_init(struct intel_dvo_device * dvo,struct i2c_adapter * adapter)471 static bool ns2501_init(struct intel_dvo_device *dvo,
472 struct i2c_adapter *adapter)
473 {
474 /* this will detect the NS2501 chip on the specified i2c bus */
475 struct ns2501_priv *ns;
476 unsigned char ch;
477
478 ns = kzalloc(sizeof(struct ns2501_priv), GFP_KERNEL);
479 if (ns == NULL)
480 return false;
481
482 dvo->i2c_bus = adapter;
483 dvo->dev_priv = ns;
484 ns->quiet = true;
485
486 if (!ns2501_readb(dvo, NS2501_VID_LO, &ch))
487 goto out;
488
489 if (ch != (NS2501_VID & 0xff)) {
490 DRM_DEBUG_KMS("ns2501 not detected got %d: from %s Slave %d.\n",
491 ch, adapter->name, dvo->slave_addr);
492 goto out;
493 }
494
495 if (!ns2501_readb(dvo, NS2501_DID_LO, &ch))
496 goto out;
497
498 if (ch != (NS2501_DID & 0xff)) {
499 DRM_DEBUG_KMS("ns2501 not detected got %d: from %s Slave %d.\n",
500 ch, adapter->name, dvo->slave_addr);
501 goto out;
502 }
503 ns->quiet = false;
504
505 DRM_DEBUG_KMS("init ns2501 dvo controller successfully!\n");
506
507 return true;
508
509 out:
510 kfree(ns);
511 return false;
512 }
513
ns2501_detect(struct intel_dvo_device * dvo)514 static enum drm_connector_status ns2501_detect(struct intel_dvo_device *dvo)
515 {
516 /*
517 * This is a Laptop display, it doesn't have hotplugging.
518 * Even if not, the detection bit of the 2501 is unreliable as
519 * it only works for some display types.
520 * It is even more unreliable as the PLL must be active for
521 * allowing reading from the chiop.
522 */
523 return connector_status_connected;
524 }
525
ns2501_mode_valid(struct intel_dvo_device * dvo,struct drm_display_mode * mode)526 static enum drm_mode_status ns2501_mode_valid(struct intel_dvo_device *dvo,
527 struct drm_display_mode *mode)
528 {
529 DRM_DEBUG_KMS
530 ("is mode valid (hdisplay=%d,htotal=%d,vdisplay=%d,vtotal=%d)\n",
531 mode->hdisplay, mode->htotal, mode->vdisplay, mode->vtotal);
532
533 /*
534 * Currently, these are all the modes I have data from.
535 * More might exist. Unclear how to find the native resolution
536 * of the panel in here so we could always accept it
537 * by disabling the scaler.
538 */
539 if ((mode->hdisplay == 640 && mode->vdisplay == 480 && mode->clock == 25175) ||
540 (mode->hdisplay == 800 && mode->vdisplay == 600 && mode->clock == 40000) ||
541 (mode->hdisplay == 1024 && mode->vdisplay == 768 && mode->clock == 65000)) {
542 return MODE_OK;
543 } else {
544 return MODE_ONE_SIZE; /* Is this a reasonable error? */
545 }
546 }
547
ns2501_mode_set(struct intel_dvo_device * dvo,const struct drm_display_mode * mode,const struct drm_display_mode * adjusted_mode)548 static void ns2501_mode_set(struct intel_dvo_device *dvo,
549 const struct drm_display_mode *mode,
550 const struct drm_display_mode *adjusted_mode)
551 {
552 const struct ns2501_configuration *conf;
553 struct ns2501_priv *ns = (struct ns2501_priv *)(dvo->dev_priv);
554 int mode_idx, i;
555
556 DRM_DEBUG_KMS
557 ("set mode (hdisplay=%d,htotal=%d,vdisplay=%d,vtotal=%d).\n",
558 mode->hdisplay, mode->htotal, mode->vdisplay, mode->vtotal);
559
560 DRM_DEBUG_KMS("Detailed requested mode settings are:\n"
561 "clock : %d kHz\n"
562 "hdisplay : %d\n"
563 "hblank start : %d\n"
564 "hblank end : %d\n"
565 "hsync start : %d\n"
566 "hsync end : %d\n"
567 "htotal : %d\n"
568 "hskew : %d\n"
569 "vdisplay : %d\n"
570 "vblank start : %d\n"
571 "hblank end : %d\n"
572 "vsync start : %d\n"
573 "vsync end : %d\n"
574 "vtotal : %d\n",
575 adjusted_mode->crtc_clock,
576 adjusted_mode->crtc_hdisplay,
577 adjusted_mode->crtc_hblank_start,
578 adjusted_mode->crtc_hblank_end,
579 adjusted_mode->crtc_hsync_start,
580 adjusted_mode->crtc_hsync_end,
581 adjusted_mode->crtc_htotal,
582 adjusted_mode->crtc_hskew,
583 adjusted_mode->crtc_vdisplay,
584 adjusted_mode->crtc_vblank_start,
585 adjusted_mode->crtc_vblank_end,
586 adjusted_mode->crtc_vsync_start,
587 adjusted_mode->crtc_vsync_end,
588 adjusted_mode->crtc_vtotal);
589
590 if (mode->hdisplay == 640 && mode->vdisplay == 480)
591 mode_idx = MODE_640x480;
592 else if (mode->hdisplay == 800 && mode->vdisplay == 600)
593 mode_idx = MODE_800x600;
594 else if (mode->hdisplay == 1024 && mode->vdisplay == 768)
595 mode_idx = MODE_1024x768;
596 else
597 return;
598
599 /* Hopefully doing it every time won't hurt... */
600 for (i = 0; i < ARRAY_SIZE(regs_init); i++)
601 ns2501_writeb(dvo, regs_init[i].offset, regs_init[i].value);
602
603 /* Write the mode-agnostic values */
604 for (i = 0; i < ARRAY_SIZE(mode_agnostic_values); i++)
605 ns2501_writeb(dvo, mode_agnostic_values[i].offset,
606 mode_agnostic_values[i].value);
607
608 /* Write now the mode-specific configuration */
609 conf = ns2501_modes + mode_idx;
610 ns->conf = conf;
611
612 ns2501_writeb(dvo, NS2501_REG8, conf->conf);
613 ns2501_writeb(dvo, NS2501_REG1B, conf->pll_a);
614 ns2501_writeb(dvo, NS2501_REG1C, conf->pll_b & 0xff);
615 ns2501_writeb(dvo, NS2501_REG1D, conf->pll_b >> 8);
616 ns2501_writeb(dvo, NS2501_REGC1, conf->hstart & 0xff);
617 ns2501_writeb(dvo, NS2501_REGC2, conf->hstart >> 8);
618 ns2501_writeb(dvo, NS2501_REGC3, conf->hstop & 0xff);
619 ns2501_writeb(dvo, NS2501_REGC4, conf->hstop >> 8);
620 ns2501_writeb(dvo, NS2501_REGC5, conf->vstart & 0xff);
621 ns2501_writeb(dvo, NS2501_REGC6, conf->vstart >> 8);
622 ns2501_writeb(dvo, NS2501_REGC7, conf->vstop & 0xff);
623 ns2501_writeb(dvo, NS2501_REGC8, conf->vstop >> 8);
624 ns2501_writeb(dvo, NS2501_REG80, conf->vsync & 0xff);
625 ns2501_writeb(dvo, NS2501_REG81, conf->vsync >> 8);
626 ns2501_writeb(dvo, NS2501_REG82, conf->vtotal & 0xff);
627 ns2501_writeb(dvo, NS2501_REG83, conf->vtotal >> 8);
628 ns2501_writeb(dvo, NS2501_REG98, conf->hpos & 0xff);
629 ns2501_writeb(dvo, NS2501_REG99, conf->hpos >> 8);
630 ns2501_writeb(dvo, NS2501_REG8E, conf->vpos & 0xff);
631 ns2501_writeb(dvo, NS2501_REG8F, conf->vpos >> 8);
632 ns2501_writeb(dvo, NS2501_REG9C, conf->voffs & 0xff);
633 ns2501_writeb(dvo, NS2501_REG9D, conf->voffs >> 8);
634 ns2501_writeb(dvo, NS2501_REGB8, conf->hscale & 0xff);
635 ns2501_writeb(dvo, NS2501_REGB9, conf->hscale >> 8);
636 ns2501_writeb(dvo, NS2501_REG10, conf->vscale & 0xff);
637 ns2501_writeb(dvo, NS2501_REG11, conf->vscale >> 8);
638 ns2501_writeb(dvo, NS2501_REGF9, conf->dither);
639 ns2501_writeb(dvo, NS2501_REG41, conf->syncb);
640 ns2501_writeb(dvo, NS2501_REGC0, conf->sync);
641 }
642
643 /* set the NS2501 power state */
ns2501_get_hw_state(struct intel_dvo_device * dvo)644 static bool ns2501_get_hw_state(struct intel_dvo_device *dvo)
645 {
646 unsigned char ch;
647
648 if (!ns2501_readb(dvo, NS2501_REG8, &ch))
649 return false;
650
651 return ch & NS2501_8_PD;
652 }
653
654 /* set the NS2501 power state */
ns2501_dpms(struct intel_dvo_device * dvo,bool enable)655 static void ns2501_dpms(struct intel_dvo_device *dvo, bool enable)
656 {
657 struct ns2501_priv *ns = (struct ns2501_priv *)(dvo->dev_priv);
658
659 DRM_DEBUG_KMS("Trying set the dpms of the DVO to %i\n", enable);
660
661 if (enable) {
662 ns2501_writeb(dvo, NS2501_REGC0, ns->conf->sync | 0x08);
663
664 ns2501_writeb(dvo, NS2501_REG41, ns->conf->syncb);
665
666 ns2501_writeb(dvo, NS2501_REG34, NS2501_34_ENABLE_OUTPUT);
667 msleep(15);
668
669 ns2501_writeb(dvo, NS2501_REG8,
670 ns->conf->conf | NS2501_8_BPAS);
671 if (!(ns->conf->conf & NS2501_8_BPAS))
672 ns2501_writeb(dvo, NS2501_REG8, ns->conf->conf);
673 msleep(200);
674
675 ns2501_writeb(dvo, NS2501_REG34,
676 NS2501_34_ENABLE_OUTPUT | NS2501_34_ENABLE_BACKLIGHT);
677
678 ns2501_writeb(dvo, NS2501_REGC0, ns->conf->sync);
679 } else {
680 ns2501_writeb(dvo, NS2501_REG34, NS2501_34_ENABLE_OUTPUT);
681 msleep(200);
682
683 ns2501_writeb(dvo, NS2501_REG8, NS2501_8_VEN | NS2501_8_HEN |
684 NS2501_8_BPAS);
685 msleep(15);
686
687 ns2501_writeb(dvo, NS2501_REG34, 0x00);
688 }
689 }
690
ns2501_destroy(struct intel_dvo_device * dvo)691 static void ns2501_destroy(struct intel_dvo_device *dvo)
692 {
693 struct ns2501_priv *ns = dvo->dev_priv;
694
695 if (ns) {
696 kfree(ns);
697 dvo->dev_priv = NULL;
698 }
699 }
700
701 const struct intel_dvo_dev_ops ns2501_ops = {
702 .init = ns2501_init,
703 .detect = ns2501_detect,
704 .mode_valid = ns2501_mode_valid,
705 .mode_set = ns2501_mode_set,
706 .dpms = ns2501_dpms,
707 .get_hw_state = ns2501_get_hw_state,
708 .destroy = ns2501_destroy,
709 };
710
