1Device tree bindings for TI's ADS7843, ADS7845, ADS7846, ADS7873, TSC2046
2SPI driven touch screen controllers.
3
4The node for this driver must be a child node of a SPI controller, hence
5all mandatory properties described in
6
7	Documentation/devicetree/bindings/spi/spi-bus.txt
8
9must be specified.
10
11Additional required properties:
12
13	compatible		Must be one of the following, depending on the
14				model:
15					"ti,tsc2046"
16					"ti,ads7843"
17					"ti,ads7845"
18					"ti,ads7846"
19					"ti,ads7873"
20
21	interrupts		An interrupt node describing the IRQ line the chip's
22				!PENIRQ pin is connected to.
23	vcc-supply		A regulator node for the supply voltage.
24
25
26Optional properties:
27
28	ti,vref-delay-usecs		vref supply delay in usecs, 0 for
29					external vref (u16).
30	ti,vref-mv			The VREF voltage, in millivolts (u16).
31					Set to 0 to use internal references
32					(ADS7846).
33	ti,keep-vref-on			set to keep vref on for differential
34					measurements as well
35	ti,swap-xy			swap x and y axis
36	ti,settle-delay-usec		Settling time of the analog signals;
37					a function of Vcc and the capacitance
38					on the X/Y drivers.  If set to non-zero,
39					two samples are taken with settle_delay
40					us apart, and the second one is used.
41					~150 uSec with 0.01uF caps (u16).
42	ti,penirq-recheck-delay-usecs	If set to non-zero, after samples are
43					taken this delay is applied and penirq
44					is rechecked, to help avoid false
45					events.  This value is affected by the
46					material used to build the touch layer
47					(u16).
48	ti,x-plate-ohms			Resistance of the X-plate,
49					in Ohms (u16).
50	ti,y-plate-ohms			Resistance of the Y-plate,
51					in Ohms (u16).
52	ti,x-min			Minimum value on the X axis (u16).
53	ti,y-min			Minimum value on the Y axis (u16).
54	ti,x-max			Maximum value on the X axis (u16).
55	ti,y-max			Minimum value on the Y axis (u16).
56	ti,pressure-min			Minimum reported pressure value
57					(threshold) - u16.
58	ti,pressure-max			Maximum reported pressure value (u16).
59	ti,debounce-max			Max number of additional readings per
60					sample (u16).
61	ti,debounce-tol			Tolerance used for filtering (u16).
62	ti,debounce-rep			Additional consecutive good readings
63					required after the first two (u16).
64	ti,pendown-gpio-debounce	Platform specific debounce time for the
65					pendown-gpio (u32).
66	pendown-gpio			GPIO handle describing the pin the !PENIRQ
67					line is connected to.
68	wakeup-source			use any event on touchscreen as wakeup event.
69					(Legacy property support: "linux,wakeup")
70
71
72Example for a TSC2046 chip connected to an McSPI controller of an OMAP SoC::
73
74	spi_controller {
75		tsc2046@0 {
76			reg = <0>;	/* CS0 */
77			compatible = "ti,tsc2046";
78			interrupt-parent = <&gpio1>;
79			interrupts = <8 0>;	/* BOOT6 / GPIO 8 */
80			spi-max-frequency = <1000000>;
81			pendown-gpio = <&gpio1 8 0>;
82			vcc-supply = <&reg_vcc3>;
83
84			ti,x-min = /bits/ 16 <0>;
85			ti,x-max = /bits/ 16 <8000>;
86			ti,y-min = /bits/ 16 <0>;
87			ti,y-max = /bits/ 16 <4800>;
88			ti,x-plate-ohms = /bits/ 16 <40>;
89			ti,pressure-max = /bits/ 16 <255>;
90
91			wakeup-source;
92		};
93	};
94