| /Linux-v6.6/drivers/net/ethernet/chelsio/cxgb/ |
| D | mv88e1xxx.h | 6 #ifndef BMCR_SPEED1000
7 # define BMCR_SPEED1000 0x40 macro
|
| D | mv88e1xxx.c | 131 ctl &= ~(BMCR_SPEED100 | BMCR_SPEED1000 | BMCR_ANENABLE); in mv88e1xxx_set_speed_duplex()
135 ctl |= BMCR_SPEED1000; in mv88e1xxx_set_speed_duplex()
142 if (ctl & BMCR_SPEED1000) /* auto-negotiation required for 1Gb/s */ in mv88e1xxx_set_speed_duplex()
|
| /Linux-v6.6/drivers/net/ |
| D | mii.c | 121 ((bmcr & BMCR_SPEED1000 && in mii_ethtool_gset()
205 cmd->base.speed = ((bmcr & BMCR_SPEED1000 && in mii_ethtool_get_link_ksettings()
302 BMCR_SPEED1000 | BMCR_FULLDPLX); in mii_ethtool_sset()
304 tmp |= BMCR_SPEED1000; in mii_ethtool_sset()
399 BMCR_SPEED1000 | BMCR_FULLDPLX); in mii_ethtool_set_link_ksettings()
401 tmp |= BMCR_SPEED1000; in mii_ethtool_set_link_ksettings()
|
| /Linux-v6.6/drivers/net/phy/ |
| D | xilinx_gmii2rgmii.c | 21 #define XILINX_GMII2RGMII_SPEED_MASK (BMCR_SPEED1000 | BMCR_SPEED100)
40 val |= BMCR_SPEED1000; in xgmiitorgmii_configure()
|
| D | marvell-88x2222.c | 123 BMCR_SPEED1000 | BMCR_SPEED100, in mv2222_set_sgmii_speed()
124 BMCR_SPEED1000); in mv2222_set_sgmii_speed()
134 BMCR_SPEED1000 | BMCR_SPEED100, in mv2222_set_sgmii_speed()
144 BMCR_SPEED1000 | BMCR_SPEED100, in mv2222_set_sgmii_speed()
|
| D | et1011c.c | 53 ctl &= ~(BMCR_FULLDPLX | BMCR_SPEED100 | BMCR_SPEED1000 | in et1011c_config_aneg()
|
| D | microchip.c | 361 temp &= ~(BMCR_SPEED100 | BMCR_SPEED1000); in lan88xx_link_change_notify()
|
| D | dp83869.c | 64 BMCR_SPEED1000)
|
| D | phy_device.c | 2277 err = phy_modify(phydev, MII_BMCR, BMCR_SPEED1000 | BMCR_SPEED100, in genphy_c37_config_aneg()
2278 BMCR_SPEED1000); in genphy_c37_config_aneg()
2444 if (bmcr & BMCR_SPEED1000) in genphy_read_status_fixed()
|
| D | marvell.c | 1535 BMCR_ANENABLE | BMCR_SPEED1000 | BMCR_FULLDPLX); in m88e6390_errata()
2007 mscr2_ctl = BMCR_SPEED1000; in m88e1510_loopback()
2012 MII_88E1510_MSCR_2, BMCR_SPEED1000 | in m88e1510_loopback()
|
| D | phy.c | 370 if (val & BMCR_SPEED1000) in phy_mii_ioctl()
|
| D | micrel.c | 1511 BMCR_SPEED1000 | BMCR_FULLDPLX | in ksz9x31_cable_test_start()
1513 BMCR_SPEED1000 | BMCR_FULLDPLX); in ksz9x31_cable_test_start()
2024 BMCR_SPEED1000 | BMCR_FULLDPLX); in lan8814_cable_test_start()
|
| D | at803x.c | 1691 mask |= ~(BMCR_SPEED1000 | BMCR_FULLDPLX); in qca83xx_suspend()
|
| /Linux-v6.6/drivers/net/ethernet/ibm/emac/ |
| D | phy.c | 123 ctl &= ~(BMCR_FULLDPLX | BMCR_SPEED100 | BMCR_SPEED1000 | BMCR_ANENABLE); in genmii_setup_aneg()
181 ctl &= ~(BMCR_FULLDPLX | BMCR_SPEED100 | BMCR_SPEED1000 | BMCR_ANENABLE); in genmii_setup_forced()
194 ctl |= BMCR_SPEED1000; in genmii_setup_forced()
267 if (bmcr & BMCR_SPEED1000) in genmii_read_link()
|
| /Linux-v6.6/include/uapi/linux/ |
| D | mdio.h | 98 #define MDIO_CTRL1_SPEEDSELEXT (BMCR_SPEED1000 | BMCR_SPEED100)
105 #define MDIO_PMA_CTRL1_SPEED1000 BMCR_SPEED1000
|
| D | mii.h | 42 #define BMCR_SPEED1000 0x0040 /* MSB of Speed (1000) */ macro
|
| /Linux-v6.6/drivers/net/ethernet/chelsio/cxgb3/ |
| D | vsc8211.c | 156 if (bmcr & BMCR_SPEED1000) in vsc8211_get_link_status()
232 if (bmcr & BMCR_SPEED1000) in vsc8211_get_link_status_fiber()
|
| D | t3_hw.c | 460 ctl &= ~(BMCR_SPEED100 | BMCR_SPEED1000 | BMCR_ANENABLE); in t3_set_phy_speed_duplex()
464 ctl |= BMCR_SPEED1000; in t3_set_phy_speed_duplex()
471 if (ctl & BMCR_SPEED1000) /* auto-negotiation required for GigE */ in t3_set_phy_speed_duplex()
|
| /Linux-v6.6/include/linux/ |
| D | mii.h | 564 bmcr = BMCR_SPEED1000; in mii_bmcr_encode_fixed()
|
| /Linux-v6.6/drivers/net/dsa/mv88e6xxx/ |
| D | pcs-6352.c | 247 BMCR_FULLDPLX | BMCR_SPEED1000, bmcr); in marvell_c22_pcs_link_up()
|
| D | pcs-639x.c | 360 BMCR_SPEED1000 | BMCR_SPEED100 | BMCR_FULLDPLX, in mv88e639x_sgmii_pcs_link_up()
|
| /Linux-v6.6/drivers/net/ethernet/dlink/ |
| D | dl2k.c | 1545 switch (bmcr & (BMCR_SPEED100 | BMCR_SPEED1000)) { in mii_get_media()
1546 case BMCR_SPEED1000: in mii_get_media()
|
| /Linux-v6.6/drivers/net/ethernet/intel/e1000e/ |
| D | phy.c | 1461 *phy_ctrl &= ~BMCR_SPEED1000; in e1000e_phy_force_speed_duplex_setup()
1465 *phy_ctrl &= ~(BMCR_SPEED1000 | BMCR_SPEED100); in e1000e_phy_force_speed_duplex_setup()
|
| /Linux-v6.6/drivers/net/ethernet/ |
| D | jme.c | 437 phylink |= ((bmcr & BMCR_SPEED1000) && in jme_check_link()
1864 BMCR_SPEED1000 | BMCR_FULLDPLX); in jme_set_100m_half()
2624 (val & BMCR_SPEED1000)) in jme_ioctl()
|
| /Linux-v6.6/drivers/net/pcs/ |
| D | pcs-xpcs.c | 1159 val = BMCR_SPEED1000; in xpcs_link_up_1000basex()
|
