| /Linux-v5.4/Documentation/devicetree/bindings/serial/ |
| D | nvidia,tegra194-tcu.txt | 6 for transmitting and one for receiving, that is used to communicate
17 "tx" - Mailbox for transmitting data to hardware UART
|
| /Linux-v5.4/Documentation/media/uapi/rc/ |
| D | lirc-get-send-mode.rst | 38 The mode used for transmitting.
72 - Device does not support transmitting.
|
| D | lirc-get-features.rst | 59 :ref:`LIRC_MODE_PULSE <lirc-mode-pulse>` can only be used for transmitting.
|
| /Linux-v5.4/drivers/media/cec/ |
| D | cec-adap.c | 376 if (data->adap->transmitting == data) { in cec_data_cancel()
377 data->adap->transmitting = NULL; in cec_data_cancel()
419 if (adap->transmitting) in cec_flush()
420 cec_data_cancel(adap->transmitting, CEC_TX_STATUS_ABORTED); in cec_flush()
457 if (adap->transmitting) { in cec_thread_func()
492 if (adap->transmitting && timeout) { in cec_thread_func()
502 adap->transmitting->msg.len, in cec_thread_func()
503 adap->transmitting->msg.msg); in cec_thread_func()
507 cec_data_cancel(adap->transmitting, in cec_thread_func()
526 adap->transmitting = data; in cec_thread_func()
[all …]
|
| /Linux-v5.4/drivers/net/team/ |
| D | Kconfig | 33 Basic mode where port used for transmitting packets is selected in
45 Basic mode where port used for transmitting packets is selected
|
| /Linux-v5.4/Documentation/devicetree/bindings/iio/health/ |
| D | afe4404.txt | 6 - tx-supply : Regulator supply to transmitting LEDs.
|
| D | afe4403.txt | 6 - tx-supply : Regulator supply to transmitting LEDs.
|
| /Linux-v5.4/drivers/media/rc/ |
| D | redrat3.c | 224 bool transmitting; member
238 if (!rr3->transmitting && (code != 0x40)) in redrat3_dump_fw_error()
276 if (!rr3->transmitting) in redrat3_dump_fw_error()
761 if (rr3->transmitting) { in redrat3_transmit_ir()
770 rr3->transmitting = true; in redrat3_transmit_ir()
847 rr3->transmitting = false; in redrat3_transmit_ir()
|
| D | ite-cir.c | 216 bool for_tx = dev->transmitting; in ite_set_carrier_params()
390 dev->transmitting = true; in ite_tx_ir()
504 dev->transmitting = false; in ite_tx_ir()
1319 wait_event_interruptible(dev->tx_ended, !dev->transmitting); in ite_close()
1638 wait_event_interruptible(dev->tx_ended, !dev->transmitting); in ite_suspend()
|
| D | ite-cir.h | 118 bool in_use, transmitting; member
|
| /Linux-v5.4/drivers/usb/class/ |
| D | cdc-acm.h | 104 int transmitting; member
|
| /Linux-v5.4/Documentation/scsi/ |
| D | cxgb3i.txt | 14 On transmitting, Chelsio S3 h/w computes and inserts the Header and
28 On transmitting, S3 h/w accepts the complete PDU (header + data)
|
| /Linux-v5.4/Documentation/devicetree/bindings/media/ |
| D | st-rc.txt | 14 protocol used for transmitting remote control signals. tx-mode should
|
| /Linux-v5.4/Documentation/devicetree/bindings/sound/ |
| D | imx-audio-spdif.txt | 15 transmitting function of S/PDIF will be enabled,
|
| /Linux-v5.4/drivers/net/hippi/ |
| D | Kconfig | 36 transmitting and receiving. This memory cannot be used by any other
|
| /Linux-v5.4/Documentation/media/uapi/cec/ |
| D | cec-pin-error-inj.rst | 98 receiving CEC messages and those relating to transmitting CEC messages. In
163 keeps transmitting after the first byte was NACKed.
195 stop transmitting ('Arbitration Lost'). This is very hard to test,
205 This setting changes the behavior of transmitting CEC messages. Normally
298 Just stop transmitting after this bit. If <op> specifies a specific CEC
|
| /Linux-v5.4/Documentation/input/ |
| D | userio.rst | 61 Registers the port with the serio driver and begins transmitting data back and
|
| /Linux-v5.4/Documentation/networking/mac80211_hwsim/ |
| D | mac80211_hwsim.rst | 44 currently enabled and on the same channel as the transmitting
|
| /Linux-v5.4/Documentation/devicetree/bindings/soc/fsl/cpm_qe/ |
| D | network.txt | 90 slots used for transmitting and receiving.
|
| /Linux-v5.4/Documentation/devicetree/bindings/mfd/ |
| D | atmel-usart.txt | 34 - atmel,use-dma-tx: use of PDC or DMA for transmitting data
|
| /Linux-v5.4/include/media/ |
| D | cec.h | 188 struct cec_data *transmitting; member
|
| /Linux-v5.4/Documentation/networking/caif/ |
| D | caif.rst | 135 might be problems transmitting over UART.
|
| /Linux-v5.4/Documentation/driver-api/serial/ |
| D | driver.rst | 126 Stop transmitting characters. This might be due to the CTS
130 The driver should stop transmitting characters as soon as
140 Start transmitting characters.
|
| /Linux-v5.4/drivers/staging/most/Documentation/ |
| D | driver_usage.txt | 205 When transmitting synchronous data the allocated channel width needs to be
223 When transmitting isochronous AVP data the desired packet size needs to be
|
| /Linux-v5.4/Documentation/devicetree/bindings/arm/ |
| D | arm,scmi.txt | 19 exactly one or two mailboxes, one for transmitting messages("tx")
|
