| /Linux-v5.4/include/linux/platform_data/ |
| D | st_sensors_pdata.h | 26 bool pullups; member
|
| /Linux-v5.4/arch/arm/boot/dts/ |
| D | omap3-cm-t3x30.dtsi | 94 /* pullups: BIT(0) */
95 ti,pullups = <0x000001>;
|
| D | omap4-sdp-es23plus.dts | 7 /* SDP boards with 4430 ES2.3+ or 4460 have external pullups on SCL & SDA */
|
| D | omap4-panda-a4.dts | 10 /* Pandaboard Rev A4+ have external pullups on SCL & SDA */
|
| D | omap4-panda-es.dts | 31 /* PandaboardES has external pullups on SCL & SDA */
|
| D | omap3-beagle-xm.dts | 327 /* pullups: BIT(1) */
328 ti,pullups = <0x000002>;
|
| D | omap3-tao3530.dtsi | 253 /* pullups: BIT(1) */
254 ti,pullups = <0x000002>;
|
| D | omap3-beagle.dts | 309 /* pullups: BIT(1) */
310 ti,pullups = <0x000002>;
|
| D | exynos5250-spring.dts | 353 * Disabled pullups since external part has its own pullups and
|
| D | exynos5250-snow-common.dtsi | 452 * Disabled pullups since external part has its own pullups and
|
| D | omap3-gta04.dtsi | 650 /* pullups: BIT(2) */
651 ti,pullups = <BIT(2)>;
|
| D | omap3-n950-n9.dtsi | 172 ti,pullups = <0x000001>; /* BIT(0) */
|
| /Linux-v5.4/drivers/gpio/ |
| D | gpio-twl4030.c | 490 &omap_twl_info->pullups); in of_gpio_twl4030()
553 ret = gpio_twl4030_pulls(pdata->pullups, pdata->pulldowns); in gpio_twl4030_probe()
556 pdata->pullups, pdata->pulldowns, ret); in gpio_twl4030_probe()
|
| /Linux-v5.4/drivers/pinctrl/sirf/ |
| D | pinctrl-sirf.c | 748 const u32 *pullups) in sirfsoc_gpio_set_pullup() argument
751 const unsigned long *p = (const unsigned long *)pullups; in sirfsoc_gpio_set_pullup()
789 u32 pullups[SIRFSOC_GPIO_NO_OF_BANKS], pulldowns[SIRFSOC_GPIO_NO_OF_BANKS]; in sirfsoc_gpio_probe() local
859 if (!of_property_read_u32_array(np, "sirf,pullups", pullups, in sirfsoc_gpio_probe()
861 sirfsoc_gpio_set_pullup(sgpio, pullups); in sirfsoc_gpio_probe()
|
| /Linux-v5.4/Documentation/devicetree/bindings/gpio/ |
| D | gpio-twl4030.txt | 17 - ti,pullups : if n-th bit is set, set a pullup on GPIO-n
|
| /Linux-v5.4/Documentation/devicetree/bindings/iio/imu/ |
| D | st_lsm6dsx.txt | 22 - st,pullups : enable/disable internal i2c controller pullup resistors.
|
| /Linux-v5.4/Documentation/devicetree/bindings/pinctrl/ |
| D | pinctrl-sirf.txt | 10 - sirf,pullups : if n-th bit of m-th bank is set, set a pullup on GPIO-n of bank m
|
| D | pinctrl-mt6797.txt | 28 configuration, pullups, drive strength, input enable/disable and input schmitt.
|
| D | pinctrl-mt65xx.txt | 48 configuration, pullups, drive strength, input enable/disable and input schmitt.
|
| D | pinctrl-mt8183.txt | 31 configuration, pullups, drive strength, input enable/disable and input schmitt.
|
| D | allwinner,sunxi-pinctrl.txt | 73 configuration, drive strength and pullups. If one of these options is
|
| /Linux-v5.4/Documentation/spi/ |
| D | butterfly.rst | 43 (a) flash new firmware that disables SPI (set PRR.2, and disable pullups
|
| /Linux-v5.4/include/linux/mfd/ |
| D | twl.h | 588 u32 pullups; member
|
| /Linux-v5.4/arch/arm64/boot/dts/rockchip/ |
| D | rk3399-gru-chromebook.dtsi | 281 * still allows us to get nice 4.7K pullups for high speed i2c
|
| /Linux-v5.4/Documentation/driver-api/gpio/ |
| D | legacy.rst | 159 and configure pullups/pulldowns appropriately.)
495 Related to multiplexing is configuration and enabling of the pullups or
498 pullups (or pulldowns) so that the on-chip ones should not be used.
|
