Searched refs:SATA (Results 1 – 25 of 149) sorted by relevance
123456
| /Linux-v5.4/Documentation/devicetree/bindings/ata/ |
| D | nvidia,tegra124-ahci.txt | 1 Tegra SoC SATA AHCI controller
9 - AHCI register set (SATA BAR5)
10 - SATA register set
11 - interrupts : Defines the interrupt used by SATA
27 - sata-phy : XUSB PADCTL SATA PHY
29 - hvdd-supply : Defines the SATA HVDD regulator
30 - vddio-supply : Defines the SATA VDDIO regulator
31 - avdd-supply : Defines the SATA AVDD regulator
32 - target-5v-supply : Defines the SATA 5V power regulator
33 - target-12v-supply : Defines the SATA 12V power regulator
|
| D | imx-sata.txt | 1 * Freescale i.MX AHCI SATA Controller
3 The Freescale i.MX SATA controller mostly conforms to the AHCI interface
8 - "fsl,imx53-ahci" for i.MX53 SATA controller
9 - "fsl,imx6q-ahci" for i.MX6Q SATA controller
10 - "fsl,imx6qp-ahci" for i.MX6QP SATA controller
11 - interrupts : interrupt mapping for SATA IRQ
24 - fsl,no-spread-spectrum : disable spread-spectrum clocking on the SATA
|
| D | exynos-sata.txt | 1 * Samsung AHCI SATA Controller
3 SATA nodes are defined to describe on-chip Serial ATA controllers.
4 Each SATA controller should have its own node.
8 - interrupts : <interrupt mapping for SATA IRQ>
17 - clock-names : Shall be "sata" for the external SATA bus clock,
|
| D | cortina,gemini-sata-bridge.txt | 1 * Cortina Systems Gemini SATA Bridge
3 The Gemini SATA bridge in a SoC-internal PATA to SATA bridge that
5 them in different configurations to two SATA ports.
11 - resets: phandles to the reset lines for both SATA bridges
17 the ATA controller and SATA bridges. Values 0..3:
37 - cortina,gemini-enable-sata-bridge: enables the PATA to SATA bridge
|
| D | ahci-platform.txt | 1 * AHCI SATA Controller
3 SATA nodes are defined to describe on-chip Serial ATA controllers.
4 Each SATA controller should have its own node.
23 - interrupts : <interrupt mapping for SATA IRQ>
34 - target-supply : regulator for SATA target power
36 - phys : reference to the SATA PHY node
53 - phys : reference to the SATA PHY node
54 - target-supply : regulator for SATA target power
|
| D | sata_highbank.txt | 1 * Calxeda AHCI SATA Controller
3 SATA nodes are defined to describe on-chip Serial ATA controllers.
4 The Calxeda SATA controller mostly conforms to the AHCI interface
6 Each SATA controller should have its own node.
10 - interrupts : <interrupt mapping for SATA IRQ>
16 SATA port to a combophy and a lane within that
|
| D | qcom-sata.txt | 1 * Qualcomm AHCI SATA Controller
3 SATA nodes are defined to describe on-chip Serial ATA controllers.
4 Each SATA controller should have its own node.
8 - interrupts : <interrupt mapping for SATA IRQ>
17 "slave_iface" - Fabric port AHB clock for SATA
|
| D | fsl-sata.txt | 1 * Freescale 8xxx/3.0 Gb/s SATA nodes
3 SATA nodes are defined to describe on-chip Serial ATA controllers.
4 Each SATA port should have its own node.
11 - interrupts : <interrupt mapping for SATA IRQ>
|
| D | ahci-st.txt | 1 STMicroelectronics STi SATA controller
3 This binding describes a SATA device.
8 - interrupts : Interrupt associated with the SATA device
16 - resets : The power-down, soft-reset and power-reset lines of SATA IP
|
| D | apm-xgene.txt | 1 * APM X-Gene 6.0 Gb/s SATA host controller nodes
3 SATA host controller nodes are defined to describe on-chip Serial ATA
4 controllers. Each SATA controller (pair of ports) have its own node.
19 - interrupts : Interrupt-specifier for SATA host controller IRQ.
24 * "sata-phy" for the SATA 6.0Gbps PHY
|
| D | brcm,sata-brcm.txt | 3 SATA nodes are defined to describe on-chip Serial ATA controllers.
4 Each SATA controller should have its own node.
15 - interrupts : interrupt mapping for SATA IRQ
|
| D | faraday,ftide010.txt | 9 SATA bridge in order to support SATA. This is why a phandle to that
26 - sata: a phande to the Gemini PATA to SATA bridge, see
|
| D | marvell.txt | 1 * Marvell Orion SATA
7 - nr-ports : Number of SATA ports in use.
|
| /Linux-v5.4/Documentation/devicetree/bindings/phy/ |
| D | qcom-ipq806x-sata-phy.txt | 1 Qualcomm IPQ806x SATA PHY Controller
4 SATA PHY nodes are defined to describe on-chip SATA Physical layer controllers.
5 Each SATA PHY controller should have its own node.
9 - reg: offset and length of the SATA PHY register set;
|
| D | qcom-apq8064-sata-phy.txt | 1 Qualcomm APQ8064 SATA PHY Controller
4 SATA PHY nodes are defined to describe on-chip SATA Physical layer controllers.
5 Each SATA PHY controller should have its own node.
9 - reg: offset and length of the SATA PHY register set;
|
| D | phy-mvebu.txt | 1 * Marvell MVEBU SATA PHY
3 Power control for the SATA phy found on Marvell MVEBU SoCs.
9 - reg : Offset and length of the register set for the SATA device
|
| D | phy-miphy365x.txt | 5 for SATA and PCIe.
29 - sata: For SATA devices
33 - st,sata-gen : Generation of locally attached SATA IP. Expected values
37 - st,sata-tx-pol-inv : Bool property to invert the polarity SATA Tx (Txn/Txp)
|
| /Linux-v5.4/Documentation/devicetree/bindings/clock/ |
| D | mvebu-gated-clock.txt | 20 15 sata0 SATA Host 0
25 30 sata1 SATA Host 0
37 14 sata0_link SATA 0 Link
38 15 sata0_core SATA 0 Core
43 20 sata1_link SATA 1 Link
44 21 sata1_core SATA 1 Core
70 15 sata0 SATA 0
79 30 sata1 SATA 1
90 15 sata0 SATA 0
109 15 sata0 SATA Host 0
[all …]
|
| /Linux-v5.4/drivers/ata/ |
| D | Kconfig | 3 # SATA/PATA driver configuration
62 bool "SATA Zero Power Optical Disc Drive (ZPODD) support"
65 This option adds support for SATA Zero Power Optical Disc
75 bool "SATA Port Multiplier support"
78 This option adds support for SATA Port Multipliers
79 (the SATA version of an ethernet hub, or SAS expander).
86 tristate "AHCI SATA support"
94 int "Default SATA Link Power Management policy for mobile chipsets"
99 Select the Default SATA Link Power Management (LPM) policy to use
113 tristate "Platform AHCI SATA support"
[all …]
|
| /Linux-v5.4/drivers/phy/st/ |
| D | phy-spear1340-miphy.c | 75 SATA, enumerator
161 if (priv->mode == SATA) in spear1340_miphy_init()
174 if (priv->mode == SATA) in spear1340_miphy_exit()
200 if (priv->mode == SATA) in spear1340_miphy_suspend()
211 if (priv->mode == SATA) in spear1340_miphy_resume()
233 if (priv->mode != SATA && priv->mode != PCIE) { in spear1340_miphy_xlate()
|
| D | Kconfig | 10 Enable this to support the miphy transceiver (for SATA/PCIE/USB3)
18 Support for ST SPEAr1310 MIPHY which can be used for PCIe and SATA.
25 Support for ST SPEAr1340 MIPHY which can be used for PCIe and SATA.
|
| /Linux-v5.4/drivers/phy/samsung/ |
| D | Kconfig | 93 Enable this to support SATA SerDes/Phy found on Samsung's
94 Exynos5250 based SoCs.This SerDes/Phy supports SATA 1.5 Gb/s,
95 SATA 3.0 Gb/s, SATA 6.0 Gb/s speeds. It supports one SATA host
96 port to accept one SATA device.
|
| /Linux-v5.4/drivers/scsi/aic94xx/ |
| D | Kconfig | 3 # Kernel configuration file for aic94xx SAS/SATA driver.
10 tristate "Adaptec AIC94xx SAS/SATA support"
15 This driver supports Adaptec's SAS/SATA 3Gb/s 64 bit PCI-X
|
| /Linux-v5.4/drivers/scsi/mvsas/ |
| D | Kconfig | 3 # Kernel configuration file for 88SE64XX/88SE94XX SAS/SATA driver.
11 tristate "Marvell 88SE64XX/88SE94XX SAS/SATA support"
16 This driver supports Marvell's SAS/SATA 3Gb/s PCI-E 88SE64XX and 6Gb/s
|
| /Linux-v5.4/drivers/scsi/megaraid/ |
| D | Kconfig.megaraid | 49 LSI MegaRAID SATA 150-4 1000:1960:1000:4523
50 LSI MegaRAID SATA 150-6 1000:1960:1000:0523
51 LSI MegaRAID SATA 300-4X 1000:0409:1000:3004
52 LSI MegaRAID SATA 300-8X 1000:0409:1000:3008
|
123456
