Searched refs:PME (Results 1 – 18 of 18) sorted by relevance
| /Linux-v5.4/Documentation/x86/ |
| D | earlyprintk.rst | 33 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
34 Status: D0 PME-Enable- DSel=0 DScale=0 PME+
|
| /Linux-v5.4/Documentation/PCI/ |
| D | pciebus-howto.rst | 35 power management event support (PME), advanced error reporting
205 Service drivers for PCI Express Power Management (PME), Advanced
218 between PME and AER. This patch assumes that all service drivers
|
| /Linux-v5.4/Documentation/devicetree/bindings/net/ |
| D | smsc911x.txt | 8 - The second interrupt (if present) is the PME (power
|
| /Linux-v5.4/arch/arm64/boot/dts/freescale/ |
| D | fsl-ls1046a.dtsi | 646 <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; /* PME interrupt */
682 <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>; /* PME interrupt */
718 <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>; /* PME interrupt */
|
| D | fsl-ls1012a.dtsi | 484 <0 117 0x4>; /* PME interrupt */
|
| D | fsl-ls1043a.dtsi | 674 <0 117 0x4>; /* PME interrupt */
|
| /Linux-v5.4/Documentation/power/ |
| D | pci.rst | 52 requiring the device to be active. After receiving a PME the kernel is supposed
55 delivering the PME from the device to the CPU and the operating system kernel.
253 interrupt whenever it receives a PME message from one of the devices below it.
254 The PCI Express Requester ID of the device that sent the PME message is then
256 read by the interrupt handler allowing the device to be identified. [PME
261 In principle the native PCI Express PME signaling may also be used on ACPI-based
266 the native PCI Express PME signaling cannot be used by the kernel in that case.
316 unsigned int pme_support:5; /* Bitmask of states from which PME#
318 unsigned int pme_interrupt:1;/* Is native PCIe PME signaling used? */
372 PCI Express PME signaling and the ACPI GPE-based wakeup signaling described in
|
| D | runtime_pm.rst | 114 PCI PME) for proper functioning and device_can_wakeup() returns 'false' for the
|
| /Linux-v5.4/arch/powerpc/boot/dts/ |
| D | xpedite5370.dts | 534 /* PME (pattern-matcher) */
|
| D | xcalibur1501.dts | 626 /* PME (pattern-matcher) */
|
| D | xpedite5301.dts | 536 /* PME (pattern-matcher) */
|
| D | xpedite5330.dts | 572 /* PME (pattern-matcher) */
|
| /Linux-v5.4/drivers/platform/x86/ |
| D | Kconfig | 949 Power Management Event (PME) to the Power Management Controller (PMC)
951 clear the PME bus 0 status bit in the GPE0a_STS register to avoid an
956 event handler to call when the PME triggers through _AEI and _L02
|
| /Linux-v5.4/arch/arm/boot/dts/ |
| D | qcom-apq8060-dragonboard.dts | 588 * The second interrupt is the PME interrupt
|
| /Linux-v5.4/drivers/hwmon/ |
| D | it87.c | 78 #define PME 0x04 /* The device with the fan registers in it */ macro
2472 superio_select(sioaddr, PME); in it87_find()
|
| /Linux-v5.4/Documentation/driver-api/pm/ |
| D | devices.rst | 421 and :c:func:`pci_enable_wake()` does something similar for the PCI PME signal.
674 issues would be issued through the PME# bus signal. Plus, there are
|
| /Linux-v5.4/Documentation/admin-guide/ |
| D | kernel-parameters.txt | 3566 native Use native PCIe services (PME, AER, DPC, PCIe hotplug)
3570 compat Disable native PCIe services (PME, AER, DPC, PCIe
3577 pcie_pme= [PCIE,PM] Native PCIe PME signaling options:
3578 nomsi Do not use MSI for native PCIe PME signaling (this makes
|
| /Linux-v5.4/drivers/eisa/ |
| D | eisa.ids | 1155 NVL1401 "Novell NE32HUB PME ISA Adapter"
|
