Searched refs:port3 (Results 1 – 25 of 25) sorted by relevance
| /Linux-v4.19/Documentation/devicetree/bindings/media/ |
| D | renesas,ceu.txt | 70 reset-gpios = <&port3 11 GPIO_ACTIVE_LOW>;
71 powerdown-gpios = <&port3 12 GPIO_ACTIVE_HIGH>;
|
| /Linux-v4.19/arch/mips/boot/dts/mscc/ |
| D | ocelot_pcb123.dts | 55 &port3 {
|
| D | ocelot.dtsi | 125 "port1", "port2", "port3", "port4", "port5",
144 port3: port@3 { label
|
| /Linux-v4.19/include/uapi/linux/ |
| D | serial.h | 90 int port3; member
|
| /Linux-v4.19/include/sound/ |
| D | emu8000.h | 71 unsigned long port3; /* Port usually at base+0x800 */ member
|
| D | emu8000_reg.h | 32 #define EMU8000_DATA3(e) ((e)->port3)
33 #define EMU8000_PTR(e) ((e)->port3+2)
|
| /Linux-v4.19/Documentation/devicetree/bindings/usb/ |
| D | pxa-usb.txt | 10 - "marvell,enable-port1", "marvell,enable-port2", "marvell,enable-port3"
|
| /Linux-v4.19/Documentation/devicetree/bindings/net/ |
| D | mscc-ocelot.txt | 63 "port1", "port2", "port3", "port4", "port5",
|
| D | keystone-netcp.txt | 78 - sgmii port3/4 module registers (only for NetCP 1.4)
84 index #1 - sgmii port3/4 module registers
|
| /Linux-v4.19/sound/isa/sb/ |
| D | emu8000.c | 1108 hw->port3 = port + 0x800; in snd_emu8000_new()
1111 !(hw->res_port3 = request_region(hw->port3, 4, "Emu8000-3"))) { in snd_emu8000_new()
1112 …_printk(KERN_ERR "sbawe: can't grab ports 0x%lx, 0x%lx, 0x%lx\n", hw->port1, hw->port2, hw->port3); in snd_emu8000_new()
|
| /Linux-v4.19/Documentation/devicetree/bindings/pinctrl/ |
| D | renesas,rza1-pinctrl.txt | 212 port3: gpio-3 {
222 gpios = <&port3 10 GPIO_ACTIVE_LOW>;
|
| /Linux-v4.19/Documentation/devicetree/bindings/mfd/ |
| D | omap-usb-host.txt | 98 port3-mode = "ehci-phy";
|
| /Linux-v4.19/arch/arm/boot/dts/ |
| D | bcm958622hr.dts | 198 label = "port3";
|
| D | bcm958625hr.dts | 204 label = "port3";
|
| D | bcm988312hr.dts | 210 label = "port3";
|
| D | bcm958623hr.dts | 202 label = "port3";
|
| D | bcm958625k.dts | 239 label = "port3";
|
| D | imx51-zii-scu3-esb.dts | 243 label = "port3";
|
| D | sun7i-a20-lamobo-r1.dts | 166 port3: port@3 { label
|
| D | omap5-cm-t54.dts | 629 port3-mode = "ehci-hsic";
|
| D | omap5-board-common.dtsi | 691 port3-mode = "ehci-hsic";
|
| D | r7s72100.dtsi | 524 port3: gpio-3 { label
|
| /Linux-v4.19/Documentation/networking/ |
| D | bonding.txt | 2157 |port3 port3|
2170 the outside world ("port3" on each switch). There is no technical
2201 example, in the above example, if the "port3" link fails at the remote
2203 monitor could be configured with a target at the remote end of port3,
2274 | Host A +------------+ switch |port3 +--------+
|
| /Linux-v4.19/drivers/scsi/cxlflash/ |
| D | main.c | 3125 static DEVICE_ATTR_RO(port3);
|
| /Linux-v4.19/drivers/net/ethernet/chelsio/cxgb3/ |
| D | t3_hw.c | 593 VPD_ENTRY(port3, 2); /* PHY3 complex */
|
