Home
last modified time | relevance | path

Searched +full:scl +full:- +full:gpios (Results 1 – 25 of 179) sorted by relevance

12345678

/Linux-v5.10/Documentation/devicetree/bindings/i2c/
Di2c-gpio.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Wolfram Sang <wolfram@the-dreams.de>
13 - $ref: /schemas/i2c/i2c-controller.yaml#
18 - const: i2c-gpio
20 sda-gpios:
24 from <dt-bindings/gpio/gpio.h> since the signal is by definition
28 scl-gpios:
[all …]
Di2c-at91.txt4 - compatible : Must be one of:
5 "atmel,at91rm9200-i2c",
6 "atmel,at91sam9261-i2c",
7 "atmel,at91sam9260-i2c",
8 "atmel,at91sam9g20-i2c",
9 "atmel,at91sam9g10-i2c",
10 "atmel,at91sam9x5-i2c",
11 "atmel,sama5d4-i2c",
12 "atmel,sama5d2-i2c",
13 "microchip,sam9x60-i2c".
[all …]
Di2c.txt8 -----------------------------
10 - #address-cells - should be <1>. Read more about addresses below.
11 - #size-cells - should be <0>.
12 - compatible - name of I2C bus controller
21 -----------------------------
26 - clock-frequency
29 - i2c-bus
31 devices and non-I2C devices, the 'i2c-bus' subnode can be used for
32 populating I2C devices. If the 'i2c-bus' subnode is present, only
34 '#address-cells' and '#size-cells' must be defined under this subnode
[all …]
Di2c-s3c2410.txt6 - compatible: value should be either of the following.
7 (a) "samsung, s3c2410-i2c", for i2c compatible with s3c2410 i2c.
8 (b) "samsung, s3c2440-i2c", for i2c compatible with s3c2440 i2c.
9 (c) "samsung, s3c2440-hdmiphy-i2c", for s3c2440-like i2c used
11 (d) "samsung, exynos5-sata-phy-i2c", for s3c2440-like i2c used as
13 - reg: physical base address of the controller and length of memory mapped
15 - interrupts: interrupt number to the cpu.
16 - samsung,i2c-sda-delay: Delay (in ns) applied to data line (SDA) edges.
18 Required for all cases except "samsung,s3c2440-hdmiphy-i2c":
19 - Samsung GPIO variant (deprecated):
[all …]
/Linux-v5.10/arch/arm/boot/dts/
Dstm32mp15xx-dhcom-drc02.dtsi1 // SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
6 #include <dt-bindings/input/input.h>
7 #include <dt-bindings/pwm/pwm.h>
17 stdout-path = "serial0:115200n8";
36 rs485-rx-en {
37 gpio-hog;
38 gpios = <8 GPIO_ACTIVE_HIGH>;
39 output-low;
40 line-name = "rs485-rx-en";
45 gpio-line-names = "", "", "", "",
[all …]
Dstm32mp15xx-dhcom-pdk2.dtsi1 // SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
3 * Copyright (C) 2019-2020 Marek Vasut <marex@denx.de>
6 #include <dt-bindings/input/input.h>
7 #include <dt-bindings/pwm/pwm.h>
17 stdout-path = "serial0:115200n8";
20 clk_ext_audio_codec: clock-codec {
21 compatible = "fixed-clock";
22 #clock-cells = <0>;
23 clock-frequency = <24000000>;
26 display_bl: display-bl {
[all …]
Dstm32mp157a-stinger96.dtsi1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
6 /dts-v1/;
9 #include "stm32mp15-pinctrl.dtsi"
10 #include "stm32mp15xxac-pinctrl.dtsi"
11 #include <dt-bindings/gpio/gpio.h>
12 #include <dt-bindings/mfd/st,stpmic1.h>
24 stdout-path = "serial1:115200n8";
33 compatible = "gpio-leds";
37 gpios = <&gpioa 13 GPIO_ACTIVE_HIGH>;
38 linux,default-trigger = "heartbeat";
[all …]
Ds5pv210-aries.dtsi1 // SPDX-License-Identifier: GPL-2.0
6 /dts-v1/;
7 #include <dt-bindings/gpio/gpio.h>
8 #include <dt-bindings/interrupt-controller/irq.h>
32 reserved-memory {
33 #address-cells = <1>;
34 #size-cells = <1>;
38 compatible = "shared-dma-pool";
39 no-map;
44 compatible = "shared-dma-pool";
[all …]
Dstm32mp15xx-dhcor-avenger96.dtsi1 // SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
3 * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
9 #include "stm32mp15xx-dhcor-io1v8.dtsi"
22 cec_clock: clk-cec-fixed {
23 #clock-cells = <0>;
24 compatible = "fixed-clock";
25 clock-frequency = <24000000>;
29 stdout-path = "serial0:115200n8";
32 hdmi-out {
33 compatible = "hdmi-connector";
[all …]
Dtegra30-apalis-eval.dts1 // SPDX-License-Identifier: GPL-2.0
2 /dts-v1/;
4 #include <dt-bindings/input/input.h>
5 #include "tegra30-apalis.dtsi"
9 compatible = "toradex,apalis_t30-eval", "toradex,apalis_t30",
23 stdout-path = "serial0:115200n8";
46 hdmi-supply = <&reg_5v0>;
75 * GEN1_I2C: I2C1_SDA/SCL on MXM3 pin 209/211 (e.g. RTC on carrier
80 clock-frequency = <400000>;
82 pcie-switch@58 {
[all …]
Dtegra30-apalis-v1.1-eval.dts1 // SPDX-License-Identifier: GPL-2.0 OR MIT
2 /dts-v1/;
4 #include <dt-bindings/input/input.h>
5 #include "tegra30-apalis-v1.1.dtsi"
9 compatible = "toradex,apalis_t30-v1.1-eval", "toradex,apalis_t30-eval",
10 "toradex,apalis_t30-v1.1", "toradex,apalis_t30",
24 stdout-path = "serial0:115200n8";
47 hdmi-supply = <&reg_5v0>;
76 * GEN1_I2C: I2C1_SDA/SCL on MXM3 pin 209/211 (e.g. RTC on carrier
81 clock-frequency = <400000>;
[all …]
Dtegra124-apalis-v1.2-eval.dts1 // SPDX-License-Identifier: GPL-2.0 OR MIT
3 * Copyright 2016-2018 Toradex AG
6 /dts-v1/;
8 #include <dt-bindings/input/input.h>
9 #include "tegra124-apalis-v1.2.dtsi"
13 compatible = "toradex,apalis-tk1-v1.2-eval", "toradex,apalis-tk1-eval",
14 "toradex,apalis-tk1-v1.2", "toradex,apalis-tk1",
28 stdout-path = "serial0:115200n8";
40 hdmi-supply = <&reg_5v0>;
69 * GEN1_I2C: I2C1_SDA/SCL on MXM3 pin 209/211 (e.g. RTC on carrier
[all …]
Dtegra124-apalis-eval.dts1 // SPDX-License-Identifier: GPL-2.0 OR X11
3 * Copyright 2016-2019 Toradex AG
6 /dts-v1/;
8 #include <dt-bindings/input/input.h>
9 #include "tegra124-apalis.dtsi"
13 compatible = "toradex,apalis-tk1-eval", "toradex,apalis-tk1",
27 stdout-path = "serial0:115200n8";
39 hdmi-supply = <&reg_5v0>;
68 * GEN1_I2C: I2C1_SDA/SCL on MXM3 pin 209/211 (e.g. RTC on carrier
73 clock-frequency = <400000>;
[all …]
Dr8a7791-koelsch.dts1 // SPDX-License-Identifier: GPL-2.0
6 * Copyright (C) 2013-2014 Renesas Solutions Corp.
11 * SSI-AK4643
38 /dts-v1/;
40 #include <dt-bindings/gpio/gpio.h>
41 #include <dt-bindings/input/input.h>
60 stdout-path = "serial0:115200n8";
74 #address-cells = <1>;
75 #size-cells = <1>;
79 compatible = "gpio-keys";
[all …]
Dexynos4412-galaxy-s3.dtsi1 // SPDX-License-Identifier: GPL-2.0
9 /dts-v1/;
10 #include "exynos4412-midas.dtsi"
20 flen-gpios = <&gpj1 1 GPIO_ACTIVE_HIGH>;
21 enset-gpios = <&gpj1 2 GPIO_ACTIVE_HIGH>;
23 pinctrl-names = "default", "host", "isp";
24 pinctrl-0 = <&camera_flash_host>;
25 pinctrl-1 = <&camera_flash_host>;
26 pinctrl-2 = <&camera_flash_isp>;
28 flash-led {
[all …]
Dat91-sama5d2_ptc_ek.dts1 // SPDX-License-Identifier: (GPL-2.0+ OR X11)
3 * at91-sama5d2_ptc_ek.dts - Device Tree file for SAMA5D2 PTC EK board
9 /dts-v1/;
11 #include "sama5d2-pinfunc.h"
12 #include <dt-bindings/mfd/atmel-flexcom.h>
13 #include <dt-bindings/gpio/gpio.h>
14 #include <dt-bindings/pinctrl/at91.h>
18 compatible = "atmel,sama5d2-ptc_ek", "atmel,sama5d2", "atmel,sama5";
28 stdout-path = "serial0:115200n8";
33 clock-frequency = <32768>;
[all …]
Dimx6q-bx50v3.dtsi5 * This file is dual-licensed: you can use it either under the terms
43 #include "imx6q-ba16.dtsi"
46 mclk: clock-mclk {
47 compatible = "fixed-clock";
48 #clock-cells = <0>;
49 clock-frequency = <22000000>;
52 gpio-poweroff {
53 compatible = "gpio-poweroff";
54 gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
58 reg_wl18xx_vmmc: regulator-wl18xx {
[all …]
Dimx6qdl-kontron-samx6i.dtsi1 // SPDX-License-Identifier: GPL-2.0 OR X11
10 #include <dt-bindings/gpio/gpio.h>
11 #include <dt-bindings/sound/fsl-imx-audmux.h>
14 reg_1p0v_s0: regulator-1p0v-s0 {
15 compatible = "regulator-fixed";
16 regulator-name = "V_1V0_S0";
17 regulator-min-microvolt = <1000000>;
18 regulator-max-microvolt = <1000000>;
19 regulator-always-on;
20 regulator-boot-on;
[all …]
Dstihxxx-b2120.dtsi1 // SPDX-License-Identifier: GPL-2.0-only
6 #include <dt-bindings/clock/stih407-clks.h>
7 #include <dt-bindings/gpio/gpio.h>
8 #include <dt-bindings/media/c8sectpfe.h>
11 compatible = "gpio-leds";
14 gpios = <&pio4 1 GPIO_ACTIVE_HIGH>;
15 linux,default-trigger = "heartbeat";
18 gpios = <&pio1 3 GPIO_ACTIVE_HIGH>;
19 default-state = "off";
24 compatible = "simple-audio-card";
[all …]
/Linux-v5.10/arch/arm64/boot/dts/rockchip/
Drk3399-sapphire-excavator.dts1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
6 /dts-v1/;
7 #include "rk3399-sapphire.dtsi"
10 model = "Excavator-RK3399 Board";
11 compatible = "rockchip,rk3399-sapphire-excavator", "rockchip,rk3399";
13 adc-keys {
14 compatible = "adc-keys";
15 io-channels = <&saradc 1>;
16 io-channel-names = "buttons";
17 keyup-threshold-microvolt = <1800000>;
[all …]
Drk3399-rockpro64.dtsi1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
7 #include <dt-bindings/input/linux-event-codes.h>
8 #include <dt-bindings/pwm/pwm.h>
10 #include "rk3399-opp.dtsi"
14 stdout-path = "serial2:1500000n8";
17 clkin_gmac: external-gmac-clock {
18 compatible = "fixed-clock";
19 clock-frequency = <125000000>;
20 clock-output-names = "clkin_gmac";
21 #clock-cells = <0>;
[all …]
Drk3399-leez-p710.dts1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
6 /dts-v1/;
7 #include <dt-bindings/input/linux-event-codes.h>
8 #include <dt-bindings/pwm/pwm.h>
10 #include "rk3399-opp.dtsi"
17 stdout-path = "serial2:1500000n8";
20 clkin_gmac: external-gmac-clock {
21 compatible = "fixed-clock";
22 clock-frequency = <125000000>;
23 clock-output-names = "clkin_gmac";
[all …]
Drk3399-roc-pc.dtsi1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
3 * Copyright (c) 2017 T-Chip Intelligent Technology Co., Ltd
6 /dts-v1/;
7 #include <dt-bindings/input/linux-event-codes.h>
8 #include <dt-bindings/pwm/pwm.h>
10 #include "rk3399-opp.dtsi"
13 model = "Firefly ROC-RK3399-PC Board";
14 compatible = "firefly,roc-rk3399-pc", "rockchip,rk3399";
17 stdout-path = "serial2:1500000n8";
21 compatible = "pwm-backlight";
[all …]
Drk3399-nanopi4.dtsi1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
3 * RK3399-based FriendlyElec boards device tree source
14 /dts-v1/;
15 #include <dt-bindings/input/linux-event-codes.h>
17 #include "rk3399-opp.dtsi"
21 stdout-path = "serial2:1500000n8";
24 clkin_gmac: external-gmac-clock {
25 compatible = "fixed-clock";
26 clock-frequency = <125000000>;
27 clock-output-names = "clkin_gmac";
[all …]
/Linux-v5.10/arch/arm64/boot/dts/marvell/
Darmada-3720-uDPU.dts1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
4 * Based on Marvell Armada 3720 development board (DB-88F3720-DDR3)
12 /dts-v1/;
14 #include <dt-bindings/gpio/gpio.h>
15 #include "armada-372x.dtsi"
22 stdout-path = "serial0:115200n8";
31 pinctrl-names = "default";
32 compatible = "gpio-leds";
36 gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
41 gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
[all …]

12345678