Searched full:powering (Results 1 – 25 of 262) sorted by relevance
1234567891011
| /Linux-v6.6/Documentation/devicetree/bindings/input/ |
| D | goodix,gt7375p.yaml | 55 Due to potential touchscreen hardware flaw, back-powering could happen in
57 This property is used to avoid the back-powering issue.
|
| /Linux-v6.6/Documentation/sound/soc/ |
| D | pops-clicks.rst | 5 Pops and clicks are unwanted audio artifacts caused by the powering up and down
21 suppression. Pops can be reduced within playback by powering the audio
|
| D | overview.rst | 42 its minimum power state at all times. This includes powering up/down
46 * Pop and click reduction. Pops and clicks can be reduced by powering the
|
| /Linux-v6.6/Documentation/firmware-guide/acpi/ |
| D | non-d0-probe.rst | 11 entire system bootup if powering on these devices has adverse side effects,
12 beyond just powering on the said device.
|
| /Linux-v6.6/drivers/macintosh/ |
| D | mediabay.c | 86 /* Wait after powering up the media bay this delay in ms
120 mb_powering_down /* Powering down (avoid too fast down/up) */
167 * Functions for powering up/down the bay, puts the bay device
338 pr_debug("mediabay%d: powering up\n", bay->index); in set_mb_power()
343 pr_debug("mediabay%d: powering down\n", bay->index); in set_mb_power()
469 /* We don't poll when powering down */ in media_bay_step()
|
| /Linux-v6.6/arch/powerpc/platforms/powernv/ |
| D | opal-power.c | 86 pr_info("EPOW msg received. Powering off system\n"); in opal_power_control_event()
91 pr_info("DPO msg received. Powering off system\n"); in opal_power_control_event()
|
| /Linux-v6.6/drivers/clk/bcm/ |
| D | clk-iproc.h | 106 * Control of powering on/off of a PLL
108 * Before powering off a PLL, input isolation (ISO) needs to be enabled
|
| /Linux-v6.6/drivers/power/reset/ |
| D | linkstation-poweroff.c | 68 /* If WOL was enabled and a magic packet was received before powering in linkstation_mvphy_reg_intn()
99 /* If WOL was enabled and a magic packet was received before powering in readynas_mvphy_set_reg()
|
| D | Kconfig | 157 This driver supports powering off a system using the Intel PIIX4
286 This driver supports powering off a system through
|
| /Linux-v6.6/Documentation/devicetree/bindings/display/panel/ |
| D | panel-common.yaml | 85 hardcode the max delay from the panel spec when powering up the panel.
136 the power-supply property specifies the supply powering the panel as a
|
| D | startek,kd070fhfid015.yaml | 22 description: Reference to the regulator powering the panel IO pins.
|
| D | mitsubishi,aa104xd12.yaml | 33 description: Reference to the regulator powering the panel VCC pins.
|
| /Linux-v6.6/drivers/gpu/drm/panel/ |
| D | panel-samsung-atna33xc20.c | 70 * powering off. in atana33xc20_suspend()
159 * powering off. in atana33xc20_disable()
187 * to wait 400 ms after powering on before asserting EL3_on. in atana33xc20_enable()
|
| /Linux-v6.6/Documentation/devicetree/bindings/power/reset/ |
| D | mt6323-poweroff.txt | 4 powering off or on the remote MediaTek SoC through the circuit BBPU.
|
| D | restart-handler.yaml | 13 Restart and shutdown handler device is responsible for powering off the
|
| /Linux-v6.6/Documentation/devicetree/bindings/leds/ |
| D | leds-cpcap.txt | 19 - vdd-supply: A phandle to the regulator powering the LED
|
| /Linux-v6.6/Documentation/devicetree/bindings/rtc/ |
| D | rtc-palmas.txt | 11 TPS80036 supports the backup battery for powering the RTC when main
|
| /Linux-v6.6/drivers/input/touchscreen/ |
| D | cy8ctmg110_ts.c | 52 * is being powered off or on. When powering on this routine de-asserts
53 * the RESET line, when powering off reset line is asserted.
|
| /Linux-v6.6/Documentation/devicetree/bindings/soc/qcom/ |
| D | qcom-stats.yaml | 14 sleep modes involving powering down of the rails and oscillator clock.
|
| /Linux-v6.6/Documentation/devicetree/bindings/power/ |
| D | brcm,bcm-pmb.yaml | 10 powering various types of connected devices (e.g. PCIe, USB, SATA).
|
| /Linux-v6.6/drivers/gpu/drm/panfrost/ |
| D | panfrost_gpu.c | 351 dev_err(pfdev->dev, "error powering up gpu L2"); in panfrost_gpu_power_on()
359 dev_err(pfdev->dev, "error powering up gpu shader"); in panfrost_gpu_power_on()
365 dev_err(pfdev->dev, "error powering up gpu tiler"); in panfrost_gpu_power_on()
|
| /Linux-v6.6/drivers/pci/hotplug/ |
| D | shpchp_ctrl.c | 468 ctrl_info(ctrl, "PCI slot #%s - powering off due to button press\n", in handle_button_press_event()
472 ctrl_info(ctrl, "PCI slot #%s - powering on due to button press\n", in handle_button_press_event()
653 ctrl_info(ctrl, "Slot %s is already in powering on state\n", in shpchp_sysfs_enable_slot()
689 ctrl_info(ctrl, "Slot %s is already in powering off state\n", in shpchp_sysfs_disable_slot()
|
| D | pciehp.h | 125 * @POWERON_STATE: slot is currently powering on
126 * @POWEROFF_STATE: slot is currently powering off
|
| /Linux-v6.6/Documentation/fb/ |
| D | sa1100fb.rst | 26 (controlling backlights, powering on the LCD, etc.), the command line
|
| /Linux-v6.6/Documentation/devicetree/bindings/mmc/ |
| D | mmc-pwrseq-simple.yaml | 42 Delay in ms after powering the card and de-asserting the
|
1234567891011
