Home
last modified time | relevance | path

Searched full:microamps (Results 1 – 22 of 22) sorted by relevance

/Linux-v6.1/Documentation/ABI/testing/
Dsysfs-class-regulator27 or microamps to determine configured regulator output levels.
106 What: /sys/class/regulator/.../microamps
112 microamps. This holds the regulator output current limit
113 setting measured in microamps (i.e. E-6 Amps), for regulators
184 microamps, for regulators which support current constraints.
187 the power domain has no min microamps constraint defined by
199 microamps, for regulators which support current constraints.
202 the power domain has no max microamps constraint defined by
236 current in microamps for this regulator from all its consumer
Dsysfs-class-power-ltc4162l27 Valid values: Signed value in microamps
70 typically drawing about 54 microamps. Write a "1" to this
72 by reducing the leakage to about 2.8 microamps. The chip will
Dsysfs-class-power60 Valid values: Represented in microamps. Negative values are
77 Valid values: Represented in microamps
100 Valid values: Represented in microamps. Negative values are
340 Valid values: Represented in microamps
350 Valid values: Represented in microamps
407 Valid values: Represented in microamps
434 Valid values: Represented in microamps
533 Valid values: Represented in microamps
665 - 100000 - 200000 (microamps), step by 25000 (rounded down)
666 - 200000 - 350000 (microamps), step by 50000 (rounded down)
/Linux-v6.1/Documentation/devicetree/bindings/iio/health/
Dmaxim,max30102.yaml26 description: RED LED current. Each step is approximately 200 microamps.
31 description: IR LED current. Each step is approximately 200 microamps.
36 description: Green LED current. Each step is approximately 200 microamps.
/Linux-v6.1/Documentation/devicetree/bindings/power/supply/
Drohm,bd99954.yaml132 description: system specific VBUS input current limit (in microamps).
138 description: system specific VCC/VACP input current limit (in microamps).
Dmax77650-charger.yaml30 CHGIN input current limit (in microamps).
Dtwl4030-charger.yaml38 description: microamps for charging the backup battery
/Linux-v6.1/drivers/power/supply/
Dpower_supply_hwmon.c225 * microvolts/microamps, so we need to adjust it to in power_supply_hwmon_read()
267 * microvolts/microamps, so we need to adjust it to in power_supply_hwmon_write()
Dbq256xx_charger.c263 * @bq256xx_def_ichg: default ichg value in microamps
264 * @bq256xx_def_iindpm: default iindpm value in microamps
266 * @bq256xx_def_iterm: default iterm value in microamps
267 * @bq256xx_def_iprechg: default iprechg value in microamps
270 * @bq256xx_max_ichg: maximum charge current in microamps
/Linux-v6.1/include/linux/regulator/
Dgpio-regulator.h28 * @value: microvolts or microamps
/Linux-v6.1/Documentation/devicetree/bindings/mfd/
Drockchip,rk817.yaml149 Value in microamps of the sleep enter current for the charger.
154 Value in microamps of the sleep filter current for the charger.
/Linux-v6.1/include/linux/mfd/
Dmax77693-private.h136 /* microamps */
146 /* microamps */
/Linux-v6.1/include/linux/mfd/wm831x/
Dpdata.h25 int ilim; /** Current limit in microamps */
/Linux-v6.1/Documentation/userspace-api/media/v4l/
Dext-ctrls-flash.rst133 independent of the flash LED. The unit should be microamps (uA) if
/Linux-v6.1/drivers/leds/
Dleds-wm8350.c17 /* Microamps */
/Linux-v6.1/Documentation/power/regulator/
Dconsumer.rst116 microamps.
/Linux-v6.1/drivers/staging/greybus/Documentation/
Dsysfs-bus-greybus60 Current measurement of the interface in microamps (uA)
/Linux-v6.1/drivers/regulator/
Dqcom-rpmh-regulator.c76 * @hpm_min_load_uA: Minimum load current in microamps that requires
313 * @load_uA: Aggregated load current in microamps
Dwm8350-regulator.c25 /* Microamps */
Dcore.c608 static DEVICE_ATTR_RO(microamps);
/Linux-v6.1/drivers/mfd/
Dwm831x-core.c29 /* Current settings - values are 2*2^(reg_val/4) microamps. These are
/Linux-v6.1/drivers/pcmcia/
Dcistpl.c46 /* Convert a power byte to a current in 0.1 microamps */