Home
last modified time | relevance | path

Searched full:asserting (Results 1 – 25 of 134) sorted by relevance

123456

/Linux-v6.6/Documentation/devicetree/bindings/mmc/
Dmmc-pwrseq-simple.yaml42 Delay in ms after powering the card and de-asserting the
47 Delay in us after asserting the reset-gpios (if any)
/Linux-v6.6/arch/powerpc/platforms/embedded6xx/
Dhlwd-pic.c27 * Enabling/disabling an interrupt line involves asserting/clearing
29 * asserting the corresponding bit in ICR.
/Linux-v6.6/Documentation/devicetree/bindings/nvmem/
Dlpc1857-eeprom.txt13 - resets: Should contain a reference to the reset controller asserting
/Linux-v6.6/include/linux/platform_data/
Dad5449.h31 * @hardware_clear_to_midscale: Whether asserting the hardware CLR pin sets the
/Linux-v6.6/Documentation/devicetree/bindings/net/bluetooth/
Dnxp,88w8987-bt.yaml15 state. De-asserting break wakes up the BT chip.
/Linux-v6.6/Documentation/devicetree/bindings/gnss/
Dgnss-common.yaml30 system can rely on asserting the line to enable the GNSS device.
/Linux-v6.6/drivers/hwmon/
Dsfctemp.c294 return dev_err_probe(dev, ret, "error asserting sense reset\n"); in sfctemp_probe()
298 return dev_err_probe(dev, ret, "error asserting bus reset\n"); in sfctemp_probe()
/Linux-v6.6/drivers/clk/qcom/
Dclk-pll.c47 * de-asserting the reset. Delay 10us just to be safe. in clk_pll_enable()
281 * de-asserting the reset. Delay 10us just to be safe. in clk_pll_sr2_enable()
/Linux-v6.6/Documentation/devicetree/bindings/net/wireless/
Dmicrochip,wilc1000.yaml38 ensure the timing required between asserting ENABLE
/Linux-v6.6/Documentation/devicetree/bindings/pci/
Dintel-gw-pcie.yaml68 Delay after asserting reset to the PCIe device.
/Linux-v6.6/drivers/gpu/drm/mgag200/
Dmgag200_bmc.c30 * done by asserting the remfreqmsk bit (XSPAREREG<7>) in mgag200_bmc_disable_vidrst()
/Linux-v6.6/drivers/pmdomain/apple/
Dpmgr-pwrstate.c124 dev_err(ps->dev, "PS 0x%x: asserting RESET while powered down\n", ps->offset); in apple_pmgr_reset_assert()
127 /* Quiesce device before asserting reset */ in apple_pmgr_reset_assert()
/Linux-v6.6/drivers/cpufreq/
Dgx-suspmod.c19 * Suspend Modulation works by asserting and de-asserting the SUSP# pin
20 * to CPU(GX1/GXLV) for configurable durations. When asserting SUSP#
/Linux-v6.6/drivers/char/ipmi/
Dipmi_si_sm.h38 * The hardware is asserting attn and the state machine is
/Linux-v6.6/drivers/bus/
Dqcom-ssc-block-bus.c170 dev_err(dev, "error asserting ssc_bcr: %d\n", ret); in qcom_ssc_block_bus_deinit()
179 dev_err(dev, "error asserting ssc_reset: %d\n", ret); in qcom_ssc_block_bus_deinit()
/Linux-v6.6/drivers/reset/
Dreset-brcmstb.c58 /* Maximum reset delay after de-asserting a line and seeing block in brcmstb_reset_deassert()
/Linux-v6.6/drivers/i2c/muxes/
DKconfig16 response mechanism where masters have to claim the bus by asserting
/Linux-v6.6/drivers/pci/pcie/
Dpme.c64 * pcie_pme_walk_bus - Scan a PCI bus for devices asserting PME#.
67 * Scan given PCI bus and all buses under it for devices asserting PME#.
/Linux-v6.6/drivers/gpu/drm/msm/hdmi/
Dhdmi_pll_8960.c266 /* Wait for a short time before de-asserting in hdmi_pll_enable()
282 * Wait for a short time before de-asserting to allow the hardware to in hdmi_pll_enable()
/Linux-v6.6/drivers/net/ethernet/xilinx/
Dll_temac_mdio.c91 /* Enable the MDIO bus by asserting the enable bit and writing in temac_mdio_setup()
/Linux-v6.6/drivers/remoteproc/
Dqcom_q6v5_adsp.c234 /* wait after asserting subsystem restart from AOSS */ in qcom_wpss_shutdown()
306 /* wait after asserting subsystem restart from AOSS */ in qcom_adsp_shutdown()
316 /* wait after de-asserting subsystem restart from AOSS */ in qcom_adsp_shutdown()
/Linux-v6.6/drivers/watchdog/
Daspeed_wdt.c440 * "This register decides the asserting duration of wdt_ext and in aspeed_wdt_probe()
442 * default asserting duration of wdt_ext and wdt_rstarm is in aspeed_wdt_probe()
/Linux-v6.6/drivers/phy/st/
Dphy-stih407-usb.c76 * case of suspend for instance. Theoretically, asserting individual in stih407_usb2_exit_port()
/Linux-v6.6/drivers/iio/adc/
Dmcp320x.c76 * @start_conv_msg: SPI message to start a conversion by briefly asserting CS
422 /* conversions are started by asserting CS pin for 8 usec */ in mcp320x_probe()
/Linux-v6.6/arch/arm/mach-omap2/
Dprminst44xx.c159 /* Check the current status to avoid de-asserting the line twice */ in omap4_prminst_deassert_hardreset()

123456