Searched full:allowable (Results 1 – 25 of 108) sorted by relevance
12345
83 * @lo: lowest allowable value84 * @hi: highest allowable value118 * @lo: minimum allowable value119 * @hi: maximum allowable value129 * @lo: minimum allowable value130 * @hi: maximum allowable value
23 * Maximum allowable number of contiguous slabs to map,
33 * @pllm_min: Minimum allowable value for PLLM[PLLM]34 * @pllm_max: Maximum allowable value for PLLM[PLLM]35 * @pllout_min_rate: Minimum allowable rate for PLLOUT36 * @pllout_max_rate: Maximum allowable rate for PLLOUT
18 This is an integer and represents allowable DMA bursts when fixed burst.19 Allowable range is 0x01-0x3F. When this field is set fixed burst is enabled.20 When fixed length is needed for burst mode, it can be set within allowable
37 Specifies the maximum power consumption allowable by a module in the
6 * may_use_simd - whether it is allowable at this time to issue SIMD
426 * @min_freq_hz: The minimum allowable frequency in Hz. This is the minimum427 * allowable programmed frequency and does not account for clock431 * @max_freq_hz: The maximum allowable frequency in Hz. This is the maximum432 * allowable programmed frequency and does not account for clock473 * @min_freq_hz: The minimum allowable frequency in Hz. This is the minimum474 * allowable programmed frequency and does not account for clock478 * @max_freq_hz: The maximum allowable frequency in Hz. This is the maximum479 * allowable programmed frequency and does not account for clock489 * This sets the desired frequency for a clock within an allowable
292 * If object was moved to an allowable region, update the object in i915_ttm_adjust_gem_after_move()294 * in an allowable region, it's evicted and we don't update the in i915_ttm_adjust_gem_after_move()691 * TTM memory type that is not in the object's allowable GEM regions, or698 * to regions that are not in the object's list of allowable placements.720 * its allowable placements. in i915_ttm_migrate()
20 * may_use_simd - whether it is allowable at this time to issue SIMD
15 Allowable values of 0x00 through 0x0F. These are raw values written to the
18 Allowable values of 0x00 through 0x0F. These are raw values written to the
158 * -min_freq: The minimum allowable frequency in Hz. This is the minimum159 * allowable programmed frequency and does not account for clock163 * -max_freq: The maximum allowable frequency in Hz. This is the maximum164 * allowable programmed frequency and does not account for clock
64 int "maximum allowable number of ranges in efi_fake_mem boot option"69 Maximum allowable number of ranges in efi_fake_mem boot option.
39 /* Powerdomain allowable state bitfields */
18 /* Max number of segments allowable in LUX table */
5 * linkmode_resolve_pause - resolve the allowable pause modes
61 * @max_core_clk_rate: maximum allowable core clock rate
287 uint16_t MaxVoltageGfx; // In mV(Q2) Maximum Voltage allowable of VDD_GFX288 uint16_t MaxVoltageSoc; // In mV(Q2) Maximum Voltage allowable of VDD_SOC
643 uint16_t MaxVoltageGfx; // In mV(Q2) Maximum Voltage allowable of VDD_GFX644 uint16_t MaxVoltageSoc; // In mV(Q2) Maximum Voltage allowable of VDD_SOC1002 uint16_t MaxVoltageGfx; // In mV(Q2) Maximum Voltage allowable of VDD_GFX1003 uint16_t MaxVoltageSoc; // In mV(Q2) Maximum Voltage allowable of VDD_SOC
59 * Max allowable width is limited on a per device basis
71 * insane value at boot (values outside of the allowable frequency in shoc_clk_init()
63 * @timeout: maximum allowable time in jiffies between start I/O and interrupt
87 countries define different levels of allowable transmitter
235 * use max allowable by PMSIDR_EL1.INTERVAL in arm_spe_pmu_default_config()
