Searched full:vout1 (Results 1 – 25 of 27) sorted by relevance
12
| /Linux-v6.1/Documentation/devicetree/bindings/mfd/ |
| D | rohm,bd9576-pmic.yaml | 32 rohm,vout1-en-low:
34 BD9576 and BD9573 VOUT1 regulator enable state can be individually
35 controlled by a GPIO. This is dictated by state of vout1-en pin during
36 the PMIC startup. If vout1-en is LOW during PMIC startup then the VOUT1
37 enable sate is controlled via this pin. Set this property if vout1-en
41 rohm,vout1-en-gpios:
43 GPIO specifier to specify the GPIO connected to vout1-en for vout1 ON/OFF
95 rohm,vout1-en-low;
96 rohm,vout1-en-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>;
|
| D | hi6421.txt | 33 regulator-name = "VOUT1";
|
| /Linux-v6.1/Documentation/devicetree/bindings/hwmon/ |
| D | ltc2978.txt | 38 * ltc2972 vout0 - vout1
42 * ltc3880, ltc3882, ltc3884, ltc3886, ltc3887, ltc3889 : vout0 - vout1
43 * ltc7880 : vout0 - vout1
45 * ltm4664 : vout0 - vout1
46 * ltm4675, ltm4676, ltm4677, ltm4678 : vout0 - vout1
47 * ltm4680, ltm4686 : vout0 - vout1
48 * ltm4700 : vout0 - vout1
|
| /Linux-v6.1/sound/soc/codecs/ |
| D | wm8770.c | 144 /* VOUT1/2/3/4 specific controls */
145 SOC_DOUBLE_R_TLV("VOUT1 Playback Volume", WM8770_VOUT1LVOL,
147 SOC_DOUBLE_R("VOUT1 Playback ZC Switch", WM8770_VOUT1LVOL,
253 SND_SOC_DAPM_MIXER("VOUT1 Mixer", SND_SOC_NOPM, 0, 0,
262 SND_SOC_DAPM_OUTPUT("VOUT1"),
280 { "VOUT1 Mixer", NULL, "VOUT12 Supply" },
281 { "VOUT1 Mixer", "DAC1 Switch", "DAC1" },
282 { "VOUT1 Mixer", "AUX1 Switch", "AUX1" },
283 { "VOUT1 Mixer", "Bypass Switch", "Capture Mux" },
299 { "VOUT1", NULL, "VOUT1 Mixer" },
|
| D | pcm1681.c | 213 SND_SOC_DAPM_OUTPUT("VOUT1"),
224 { "VOUT1", NULL, "Playback" },
|
| /Linux-v6.1/drivers/regulator/ |
| D | bd9576-regulator.c | 797 /* There is 1 bit gap in register after Vout1 .. Vout4 statuses */ in bd9576_uvd_handler()
839 /* There is 1 bit gap in register after Vout1 .. Vout4 statuses */ in bd9576_ovd_handler()
944 "rohm,vout1-en-low"); in bd957x_probe()
950 /* VOUT1 enable state judged by VOUT1_EN pin */ in bd957x_probe()
954 "rohm,vout1-en", GPIOD_OUT_LOW, in bd957x_probe()
955 "vout1-en"); in bd957x_probe()
967 * vout1-en LOW during OTP loading and set VOUT1 to be in bd957x_probe()
972 * I believe such case where rohm,vout1-en-low is set in bd957x_probe()
973 * and vout1-en-gpios is not is likely to be a in bd957x_probe()
977 "Failed to get VOUT1 control GPIO\n"); in bd957x_probe()
[all …]
|
| D | 88pm800-regulator.c | 23 #define PM800_LDO1_VOUT (0x08) /* VOUT1 */
|
| /Linux-v6.1/Documentation/hwmon/ |
| D | adm1275.rst | 103 inX_label "vin1" or "vout1" depending on chip variant and
105 vout1 reports the voltage on the VAUX pin.
|
| D | ir36021.rst | 47 in2_label "vout1"
|
| D | q54sj108a2.rst | 51 in2_label RO 'vout1'
|
| D | ibm-cffps.rst | 45 in2_label "vout1"
|
| D | bpa-rs600.rst | 52 in2_label "vout1"
|
| D | dps920ab.rst | 53 in2_label "vout1"
|
| D | ltc3815.rst | 46 in2_label "vout1".
|
| D | inspur-ipsps1.rst | 48 in2_label "vout1"
|
| D | ir38064.rst | 71 in2_label "vout1"
|
| D | max20730.rst | 76 in2_label RO 'vout1'
|
| D | max20751.rst | 60 in2_label "vout1"
|
| D | max15301.rst | 70 in2_label "vout1"
|
| D | max8688.rst | 48 in1_label "vout1"
|
| D | stpddc60.rst | 66 in2_label "vout1"
|
| D | lm25066.rst | 113 in3_label "vout1"
|
| D | max16601.rst | 69 in2_label "vout1"
|
| /Linux-v6.1/Documentation/devicetree/bindings/regulator/ |
| D | maxim,max20086.yaml | 92 regulator-name = "VOUT1";
|
| /Linux-v6.1/arch/arm64/boot/dts/ti/ |
| D | k3-am65-iot2050-common.dtsi | 288 dss_vout1_pins_default: dss-vout1-pins-default {
|
12
