Searched full:mx53 (Results 1 – 25 of 30) sorted by relevance
12
| /Linux-v5.15/Documentation/devicetree/bindings/display/imx/ |
| D | ldb.txt | 16 - gpr : should be <&gpr> on i.MX53 and i.MX6q.
22 The following clocks are expected on i.MX53:
37 - pinctrl-names : should be "default" on i.MX53, not used on i.MX6q
38 - pinctrl-0 : a phandle pointing to LVDS pin settings on i.MX53,
|
| /Linux-v5.15/drivers/gpu/drm/imx/ |
| D | Kconfig | 26 found on i.MX53 processors.
35 found on i.MX53 and i.MX6 processors.
|
| D | imx-ldb.c | 648 * i.MX53: ipu1_di0_sel, ipu1_di1_sel in imx_ldb_probe()
|
| /Linux-v5.15/arch/arm/mach-imx/ |
| D | Kconfig | 127 bool "i.MX53 support"
132 This enables support for Freescale i.MX53 processor.
|
| D | mach-imx53.c | 42 DT_MACHINE_START(IMX53_DT, "Freescale i.MX53 (Device Tree Support)")
|
| D | hardware.h | 73 * mx53:
|
| D | pm-imx5.c | 141 * mx5 because it can be used for mx51, and mx53.
|
| /Linux-v5.15/Documentation/devicetree/bindings/rtc/ |
| D | rtc-mxc_v2.yaml | 7 title: i.MX53 Secure Real Time Clock (SRTC)
|
| /Linux-v5.15/Documentation/devicetree/bindings/nvmem/ |
| D | imx-iim.yaml | 14 i.MX25, i.MX27, i.MX31, i.MX35, i.MX51 and i.MX53 SoCs.
|
| /Linux-v5.15/arch/arm/boot/dts/ |
| D | imx53-qsb.dts | 10 model = "Freescale i.MX53 Quick Start Board";
|
| D | imx53-ard.dts | 12 model = "Freescale i.MX53 Automotive Reference Design Board";
|
| D | imx53-qsrb.dts | 11 model = "Freescale i.MX53 Quick Start-R Board";
|
| D | imx53-usbarmory.dts | 79 * Not every i.MX53 P/N supports clock > 800MHz.
|
| D | imx53-voipac-dmm-668.dtsi | 9 model = "Voipac i.MX53 X53-DMM-668";
|
| D | imx53-smd.dts | 11 model = "Freescale i.MX53 Smart Mobile Reference Design Board";
|
| /Linux-v5.15/drivers/rtc/ |
| D | rtc-mxc_v2.c | 3 * Real Time Clock (RTC) Driver for i.MX53
389 MODULE_DESCRIPTION("Real Time Clock (RTC) Driver for i.MX53");
|
| D | Kconfig | 1752 tristate "Freescale MXC Real Time Clock for i.MX53"
1758 SRTC module in i.MX53 processor.
|
| /Linux-v5.15/Documentation/devicetree/bindings/arm/ |
| D | fsl.yaml | 161 - description: i.MX53 based Boards
168 - fsl,imx53-qsrb # Freescale i.MX53 Quick Start-R Board
176 - voipac,imx53-dmm-668 # Voipac i.MX53 X53-DMM-668
179 - description: i.MX53 based Aries/DENX M53EVK Board
185 - description: i.MX53 based TQ MBa53 Board
|
| /Linux-v5.15/Documentation/devicetree/bindings/bus/ |
| D | imx-weim.txt | 61 For i.MX50, i.MX53 ("fsl,imx50-weim"),
|
| /Linux-v5.15/drivers/soc/imx/ |
| D | soc-imx.c | 82 soc_id = "i.MX53"; in imx_soc_device_init()
|
| /Linux-v5.15/drivers/gpu/ipu-v3/ |
| D | ipu-di.c | 360 /* PIN4: HSYNC for VGA via TVEv2 on i.MX53-QSB */ in ipu_di_sync_config_noninterlaced()
369 /* PIN6: VSYNC for VGA via TVEv2 on i.MX53-QSB */ in ipu_di_sync_config_noninterlaced()
|
| /Linux-v5.15/drivers/clk/imx/ |
| D | clk-imx5.c | 305 * it comes closest in scope to the main_bus_clk of i.MX51 and i.MX53 in mx50_clocks_init()
606 imx_print_silicon_rev("i.MX53", mx53_revision()); in mx53_clocks_init()
|
| /Linux-v5.15/arch/arm/ |
| D | Kconfig.debug | 457 bool "i.MX53 Debug UART"
461 on i.MX53.
|
| /Linux-v5.15/drivers/net/can/ |
| D | flexcan.c | 218 * MX53 FlexCAN2 03.00.00.00 yes no no no no no 64
279 u32 gfwr_mx28; /* MX28, MX53 */
299 * (mx25, mx28, mx35, mx53)
|
| /Linux-v5.15/drivers/mmc/host/ |
| D | sdhci-esdhc-imx.c | 901 /* For i.MX53 eSDHCv3, SYSCTL.SDCLKFS may not be set to 0. */ in esdhc_pltfm_set_clock()
904 * According to the i.MX53 reference manual, if DLLCTRL[10] can in esdhc_pltfm_set_clock()
|
12
