Home
last modified time | relevance | path

Searched +full:625 +full:v (Results 1 – 25 of 43) sorted by relevance

12

/Linux-v5.10/drivers/media/pci/cx18/
Dcx18-av-core.c118 u32 v; in cx18_av_initialize() local
126 v = cx18_av_read4(cx, CXADEC_HOST_REG1); in cx18_av_initialize()
128 cx18_av_write4_expect(cx, CXADEC_HOST_REG1, v | 1, v, 0xfffe); in cx18_av_initialize()
130 cx18_av_write4_expect(cx, CXADEC_HOST_REG1, v & 0xfffe, in cx18_av_initialize()
131 v & 0xfffe, 0xffff); in cx18_av_initialize()
134 v = cx18_av_read4(cx, CXADEC_DLL1_DIAG_CTRL) & 0xE1FFFEFF; in cx18_av_initialize()
136 cx18_av_write4(cx, CXADEC_DLL1_DIAG_CTRL, v); in cx18_av_initialize()
138 cx18_av_write4(cx, CXADEC_DLL1_DIAG_CTRL, v | 0x10000100); in cx18_av_initialize()
140 v = cx18_av_read4(cx, CXADEC_DLL2_DIAG_CTRL) & 0xE1FFFEFF; in cx18_av_initialize()
142 cx18_av_write4(cx, CXADEC_DLL2_DIAG_CTRL, v); in cx18_av_initialize()
[all …]
Dcx18-streams.c578 * For 625/50 systems, according to the VIP 2 & BT.656 std: in cx18_vbi_setup()
623 * Since the V bit is only allowed to toggle in the EAV RP code, in cx18_vbi_setup()
857 * Field 1 is 312 for 625 line systems in BT.656 in cx18_start_v4l2_encode_stream()
858 * Field 2 is 313 for 625 line systems in BT.656 in cx18_start_v4l2_encode_stream()
Dcx18-driver.h476 * PAL-B/G/H, PAL-I, SECAM-L and other 50 Hz/625 line systems, we have:
481 #define VBI_ACTIVE_SAMPLES 1444 /* 4 byte SAV + 720 Y + 720 U/V */
566 struct v4l2_subdev *sd_av; /* A/V decoder/digitizer sub-device */
/Linux-v5.10/drivers/iio/adc/
Dqcom-vadc-common.h12 /* Min ADC code represents 0V */
14 /* Max ADC code represents full-scale range of 1.8V */
72 * VADC_CALIB_ABSOLUTE: uses the 625mV and 1.25V as reference channels.
73 * VADC_CALIB_RATIOMETRIC: uses the reference voltage (1.8V) and GND for
Dqcom-pm8xxx-xoadc.c127 * @PM8XXX_CHANNEL_INTERNAL: 625mV reference channel
240 XOADC_CHAN(125V, 0x00, 0x0d, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1),
264 XOADC_CHAN(125V, 0x00, 0x0d, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1),
299 XOADC_CHAN(125V, 0x00, 0x0d, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1),
324 XOADC_CHAN(125V, 0x00, 0x0d, IIO_VOLTAGE, 1, 1, SCALE_DEFAULT, AMUX_RSV1),
599 dev_err(adc->dev, "could not read 1.25V reference channel\n"); in pm8xxx_calibrate_device()
607 dev_err(adc->dev, "could not read 0.625V reference channel\n"); in pm8xxx_calibrate_device()
611 dev_err(adc->dev, "read same ADC code for 1.25V and 0.625V\n"); in pm8xxx_calibrate_device()
865 dev_err(adc->dev, "missing 1.25V reference channel\n"); in pm8xxx_xoadc_parse_channels()
870 dev_err(adc->dev, "missing 0.625V reference channel\n"); in pm8xxx_xoadc_parse_channels()
Dqcom-spmi-vadc.c366 /* Try with buffered 625mV channel first */ in vadc_measure_ref_points()
784 dev_err(vadc->dev, "Please define 1.25V channel\n"); in vadc_get_dt_data()
789 dev_err(vadc->dev, "Please define 0.625V channel\n"); in vadc_get_dt_data()
/Linux-v5.10/Documentation/devicetree/bindings/iio/adc/
Dqcom,pm8xxx-xoadc.txt19 with PMIC variant but is typically something like 2.2 or 1.8V.
62 1:1 ratio converters that sample 625, 1250 and 0 milliV and create
92 calibrated with the 0.625V and 1.25V reference channels, also
154 <&xoadc 0x00 0x0c>, /* Reference voltage 1.25V */
155 <&xoadc 0x00 0x0d>, /* Reference voltage 0.625V */
156 <&xoadc 0x00 0x0e>; /* Reference voltage 0.325V */
/Linux-v5.10/Documentation/userspace-api/media/v4l/
Dconstraints.svg5 …ill-rule="evenodd" stroke="#000080" stroke-linejoin="round" stroke-width=".625"/></marker></defs><…
6 …d="path209" d="m13800 17500h-12400v-14200h24800v14200h-12400z" fill="#fff"/><path id="path211" d="…
8 …th id="path247" d="m11000 13400h-3900v-5400h7800v5400h-3900z" fill="#fff"/><path id="path249" d="m…
9 …"10600" width="101" height="1301" fill="none"/><path id="path285" d="m9650 11850v-1200" fill="none"
10 …550" width="601" height="1451" fill="none"/><path id="path310" d="m9837 1950v-1453" fill="none" ma…
Dselection.svg308 …625-1.255.412-1.687.19-5.282 1.438-3.39 1.177-8.595 3.213-9.78 4.156-1.525.06-3.65.395-5.532 1.062…
460 …625-1.255.412-1.687.19-5.282 1.438-3.39 1.177-8.595 3.213-9.78 4.156-1.525.06-3.65.395-5.532 1.062…
753 …<circle transform="translate(47.589 -.625)" cx="413.66" cy="401.83" r="3.214" enable-background="a…
788 …499-5.5 1.219a1047.26 1047.26 0 0 1-6.437 2.469c-.617.233-.997.442-1.281.593v.031l-8 3.188-12.476 …
795 2.063-.627.205-.992.392-1.281.531-.408.214-.653.409-1.313.625-1.254.412-1.686.19-5.28 1.438-3.39 1.…
798 …-.086-.632 1-1.03c.73-.269 5.048-1.339 7.126-1.813 2.008-.46 5.168-1.03 7-.625 1.878.414 13.578 3.…
803 …25 2.25-2.964.326-6.521-.015-10.906-1.905-3.978-1.715-5.339-2.916-9.406-4.75v.156c3.643 2.095 5.28…
804 …v.156c3.656 2.204 5.295 4.053 8.907 5.906 1.74.893 3.637 1.528 5.469 1.969-.54.248-1.578.615-3.469…
805 …8 1.813-2.971.283-6.573-.176-10.938-1.938-3.96-1.598-5.329-2.795-9.344-4.312v.156c3.596 1.811 5.23…
806 …v.156c3.484 1.395 5.07 2.92 8.53 4.032 1.669.535 3.457.786 5.22.875-.52.352-1.5.914-3.313 1.53-2.7…
[all …]
/Linux-v5.10/drivers/staging/media/zoran/
Dzoran_card.c272 static const struct tvnorm f50sqpixel = { 944, 768, 83, 880, 625, 576, 16 };
274 static const struct tvnorm f50ccir601 = { 864, 720, 75, 804, 625, 576, 18 };
277 static const struct tvnorm f50ccir601_lml33 = { 864, 720, 75 + 34, 804, 625, 576, 18 };
281 static const struct tvnorm f50sqpixel_dc10 = { 944, 768, 0, 880, 625, 576, 0 };
285 * FIXME: I cannot swap U and V in saa7114, so i do one pixel left shift in zoran (75 -> 74)
288 static const struct tvnorm f50ccir601_lm33r10 = { 864, 720, 74 + 54, 804, 625, 576, 18 };
292 * FIXME: The ks0127 seem incapable of swapping U and V, too, which is why I copy Maxim's left
298 static const struct tvnorm f50ccir601_avs6eyes = { 864, 720, 74, 804, 625, 576, 18 };
/Linux-v5.10/drivers/power/supply/
Dmax17042_battery.c151 * supply is e.g. only delivering 5V 0.5A. Check current if available. in max17042_get_status()
183 vavg = val * 625 / 8; in max17042_get_battery_health()
192 vbatt = val * 625 / 8; in max17042_get_battery_health()
301 val->intval = data * 625 / 8; in max17042_get_property()
308 val->intval = data * 625 / 8; in max17042_get_property()
315 val->intval = data * 625 / 8; in max17042_get_property()
Dds2760_battery.c231 1800, /* HP iPAQ hx4700 3.7V 1800mAh (359113-001) */
242 3600, /* HP iPAQ hx4700 3.7V 3600mAh (359114-001) */
297 * class reports in units of µA, so convert by multiplying by 625. */ in ds2760_battery_read_status()
301 di->current_uA = di->current_raw * 625; in ds2760_battery_read_status()
/Linux-v5.10/drivers/gpu/drm/
Ddrm_edid.c255 896, 1024, 0, 600, 601, 603, 625, 0,
267 896, 1056, 0, 600, 601, 604, 625, 0,
594 896, 1024, 0, 600, 601, 603, 625, 0,
630 928, 1152, 0, 624, 625, 628, 667, 0,
633 896, 1056, 0, 600, 601, 604, 625, 0,
808 796, 864, 0, 576, 581, 586, 625, 0,
813 796, 864, 0, 576, 581, 586, 625, 0,
829 795, 864, 0, 576, 580, 586, 625, 0,
835 795, 864, 0, 576, 580, 586, 625, 0,
853 3180, 3456, 0, 576, 580, 586, 625, 0,
[all …]
/Linux-v5.10/drivers/gpu/drm/amd/pm/inc/
Dhwmgr.h39 #define VOLTAGE_VID_OFFSET_SCALE1 625
99 uint32_t v; member
105 uint32_t v; member
111 uint32_t v; member
116 uint32_t v; member
121 uint32_t v; member
138 uint32_t v; member
148 uint32_t v; member
159 uint32_t v; member
402 uint32_t v; member
/Linux-v5.10/drivers/media/i2c/
Dbt819.c71 {864 - 24, 20, 625 - 2, 1, 0x0504, 0x0000},
155 0x0e, 0xb4, /* 0x0e Chroma Gain (V) msb */ in bt819_init()
346 /* Ratio between U gain and V gain must stay the same as in bt819_s_ctrl()
347 the ratio between the default U and V gain values. */ in bt819_s_ctrl()
Dsaa7115.c495 R_F0_LFCO_PER_LINE, 0xb0, /* Set PLL Register. 50hz 625 lines per frame, 27 MHz */
950 /* write V fine-scaling (luminance) */ in saa711x_set_size()
955 /* write V fine-scaling (chrominance) */ in saa711x_set_size()
1012 50 Hz / 625 lines 60 Hz / 525 lines in saa711x_set_v4lstd()
1147 u8 v = saa711x_read(sd, i - 2 + R_41_LCR_BASE); in saa711x_g_sliced_fmt() local
1149 sliced->service_lines[0][i] = lcr2vbi[v >> 4]; in saa711x_g_sliced_fmt()
1150 sliced->service_lines[1][i] = lcr2vbi[v & 0xf]; in saa711x_g_sliced_fmt()
/Linux-v5.10/drivers/media/i2c/cx25840/
Dcx25840-ir.c380 u32 v; in control_rx_s_carrier_window() local
384 v = CNTRL_WIN_3_4; in control_rx_s_carrier_window()
387 v = CNTRL_WIN_3_3; in control_rx_s_carrier_window()
392 v |= CNTRL_WIN_4_3; in control_rx_s_carrier_window()
395 v |= CNTRL_WIN_3_3; in control_rx_s_carrier_window()
398 cx25840_and_or4(c, CX25840_IR_CNTRL_REG, ~CNTRL_WIN, v); in control_rx_s_carrier_window()
462 n = DIV_ROUND_CLOSEST(duty_cycle * 100, 625); /* 16ths of 100% */ in cduty_tx_s_duty_cycle()
517 u32 events, v; in cx25840_ir_irq_handler() local
588 for (i = 0, v = FIFO_RX_NDV; in cx25840_ir_irq_handler()
589 (v & FIFO_RX_NDV) && !kror; i = 0) { in cx25840_ir_irq_handler()
[all …]
/Linux-v5.10/drivers/media/pci/cx23885/
Dcx23888-ir.c373 u32 v; in control_rx_s_carrier_window() local
377 v = CNTRL_WIN_3_4; in control_rx_s_carrier_window()
380 v = CNTRL_WIN_3_3; in control_rx_s_carrier_window()
385 v |= CNTRL_WIN_4_3; in control_rx_s_carrier_window()
388 v |= CNTRL_WIN_3_3; in control_rx_s_carrier_window()
391 cx23888_ir_and_or4(dev, CX23888_IR_CNTRL_REG, ~CNTRL_WIN, v); in control_rx_s_carrier_window()
462 n = DIV_ROUND_CLOSEST(duty_cycle * 100, 625); /* 16ths of 100% */ in cduty_tx_s_duty_cycle()
513 u32 events, v; in cx23888_ir_irq_handler() local
568 for (i = 0, v = FIFO_RX_NDV; in cx23888_ir_irq_handler()
569 (v & FIFO_RX_NDV) && !kror; i = 0) { in cx23888_ir_irq_handler()
[all …]
/Linux-v5.10/include/uapi/linux/
Dvideodev2.h496 * V I D E O I M A G E F O R M A T
583 #define V4L2_PIX_FMT_UV8 v4l2_fourcc('U', 'V', '8', ' ') /* 8 UV 4:4 */
586 #define V4L2_PIX_FMT_YUYV v4l2_fourcc('Y', 'U', 'Y', 'V') /* 16 YUV 4:2:2 */
587 #define V4L2_PIX_FMT_YYUV v4l2_fourcc('Y', 'Y', 'U', 'V') /* 16 YUV 4:2:2 */
588 #define V4L2_PIX_FMT_YVYU v4l2_fourcc('Y', 'V', 'Y', 'U') /* 16 YVU 4:2:2 */
589 #define V4L2_PIX_FMT_UYVY v4l2_fourcc('U', 'Y', 'V', 'Y') /* 16 YUV 4:2:2 */
590 #define V4L2_PIX_FMT_VYUY v4l2_fourcc('V', 'Y', 'U', 'Y') /* 16 YUV 4:2:2 */
593 #define V4L2_PIX_FMT_YUV555 v4l2_fourcc('Y', 'U', 'V', 'O') /* 16 YUV-5-5-5 */
594 #define V4L2_PIX_FMT_YUV565 v4l2_fourcc('Y', 'U', 'V', 'P') /* 16 YUV-5-6-5 */
595 #define V4L2_PIX_FMT_YUV32 v4l2_fourcc('Y', 'U', 'V', '4') /* 32 YUV-8-8-8-8 */
[all …]
/Linux-v5.10/drivers/staging/comedi/drivers/
Damplc_pci224.c53 * 0: [-10V,+10V]; 1: [-5V,+5V]; 2: [-2.5V,+2.5V], 3: [-1.25V,+1.25V],
54 * 4: [0,+10V], 5: [0,+5V], 6: [0,+2.5V], 7: [0,+1.25V]
67 * an internal 5V reference and an external voltage reference (Vext).
73 * 2-3 (factory) 1-2 (factory) 0: [-10V,+10V]
74 * 2-3 (factory) 2-3 1: [-5V,+5V]
138 #define PCI224_DACCON_POLAR_UNI PCI224_DACCON_POLAR(0) /* [0,+V] */
139 #define PCI224_DACCON_POLAR_BI PCI224_DACCON_POLAR(1) /* [-V,+V] */
143 #define PCI224_DACCON_VREF_1_25 PCI224_DACCON_VREF(0) /* 1.25V */
144 #define PCI224_DACCON_VREF_2_5 PCI224_DACCON_VREF(1) /* 2.5V */
145 #define PCI224_DACCON_VREF_5 PCI224_DACCON_VREF(2) /* 5V */
[all …]
/Linux-v5.10/drivers/video/fbdev/
Damifb.c114 | | v | | |
135 | # v # | |
139 | | v | | |
143 | | v | | |
329 - we have 625 scanlines, of which 575 are visible (interlaced); after
344 - make sure upper_margin + yres + lower_margin + vsync_len = 625 for an
531 #define PAL_VTOTAL (625)
543 #define up2(v) (((v) + 1) & -2) argument
544 #define down2(v) ((v) & -2) argument
545 #define div2(v) ((v)>>1) argument
[all …]
/Linux-v5.10/drivers/media/common/v4l2-tpg/
Dv4l2-tpg-colors.c164 622, 623, 624, 625, 625, 626, 627, 627, 628, 629, 630, 630, 631, 632, 632, 633,
338 592, 595, 598, 601, 604, 607, 610, 613, 616, 619, 622, 625, 628, 631, 634, 637,
1165 static double transfer_srgb_to_rgb(double v) in transfer_srgb_to_rgb() argument
1167 if (v < -0.04045) in transfer_srgb_to_rgb()
1168 return pow((-v + 0.055) / 1.055, 2.4); in transfer_srgb_to_rgb()
1169 return (v <= 0.04045) ? v / 12.92 : pow((v + 0.055) / 1.055, 2.4); in transfer_srgb_to_rgb()
1172 static double transfer_rgb_to_srgb(double v) in transfer_rgb_to_srgb() argument
1174 if (v <= -0.0031308) in transfer_rgb_to_srgb()
1175 return -1.055 * pow(-v, 1.0 / 2.4) + 0.055; in transfer_rgb_to_srgb()
1176 if (v <= 0.0031308) in transfer_rgb_to_srgb()
[all …]
/Linux-v5.10/drivers/video/fbdev/sis/
Dinitdef.h132 /* v-- Needs change in sis_vga.c if changed (GPIO) --v */
500 #define PALVT 625
/Linux-v5.10/drivers/gpu/drm/radeon/
Dradeon_legacy_tv.c15 * Limits of h/v positions (hPos & vPos)
45 #define PAL_TV_LINES_PER_FRAME 625
492 DRM_DEBUG_KMS("compute_restarts: def = %u h = %d v = %d, p1 = %04x, p2 = %04x, restart = %d\n", in radeon_legacy_tv_init_restarts()
501 DRM_DEBUG_KMS("compute_restart: F/H/V=%u,%u,%u\n", in radeon_legacy_tv_init_restarts()
/Linux-v5.10/drivers/gpu/ipu-v3/
Dipu-csi.c391 * Write the H-V-F codes the CSI will match against the in ipu_csi_set_bt_interlaced_codes()
478 height = 625; in ipu_csi_init_interface()

12