Searched refs:programmed (Results 1 – 25 of 61) sorted by relevance
123
| /Zephyr-latest/tests/drivers/pwm/pwm_gpio_loopback/ |
| D | Kconfig | 27 Maximum allowed deviation (%) from the programmed values for the test to be
29 can deviate by up to 5% from the programmed values for the test to pass.
|
| /Zephyr-latest/boards/makerdiary/nrf52840_mdk_usb_dongle/ |
| D | Kconfig.defconfig | 12 # must be linked after Nordic MBR, that is factory-programmed on the board.
|
| /Zephyr-latest/boards/nordic/nrf52840dongle/ |
| D | Kconfig.defconfig | 10 # must be linked after Nordic MBR, that is factory-programmed on the board.
|
| /Zephyr-latest/boards/others/promicro_nrf52840/ |
| D | Kconfig.defconfig | 11 # must be linked after Nordic MBR, that is factory-programmed on the board.
|
| /Zephyr-latest/boards/ezurio/bl654_usb/ |
| D | Kconfig.defconfig | 9 # must be linked after Nordic MBR, that is factory-programmed on the board.
|
| /Zephyr-latest/modules/hal_nordic/ |
| D | Kconfig.nrf_regtool | 12 being programmed alongside the firmware.
|
| /Zephyr-latest/drivers/rtc/ |
| D | Kconfig.pcf8523 | 27 per minute until the programmed correction values have been implemented (MODE = 0).
|
| /Zephyr-latest/doc/connectivity/networking/api/ |
| D | promiscuous.rst | 15 passing only the frames that the controller is specifically programmed
|
| /Zephyr-latest/boards/shields/link_board_eth/doc/ |
| D | index.rst | 26 - Factory Pre-programmed Unique MAC Address
|
| /Zephyr-latest/drivers/interrupt_controller/ |
| D | Kconfig.loapic | 24 interrupt that was to be dispensed has become masked (programmed
|
| /Zephyr-latest/drivers/dai/intel/dmic/ |
| D | Kconfig.dmic | 77 the value to be programmed is 4799 (12BFh)
|
| /Zephyr-latest/drivers/flash/ |
| D | Kconfig | 24 on write) and requires explicit erase procedure to be programmed
25 with random value, in place where it has already been programmed with
50 programmed with some other value.
|
| D | Kconfig.simulator | 43 bool "Allow program units to be programmed more than once"
|
| D | Kconfig.mcux | 31 devices will crash when reading an erased or wrongly programmed area.
|
| /Zephyr-latest/doc/hardware/arch/ |
| D | arm_cortex_m.rst | 181 configured *once* during kernel boot, while PSLIM is re-programmed during every thread
417 * MPU guards are re-programmed at every context-switch, adding a small overhead to the
434 are programmed during system boot.
458 region will be allocated and programmed during system boot. When used with the
480 Additional *static* MPU regions may be programmed once during system boot. These regions
496 Certain thread-specific MPU regions may be re-programmed dynamically, at each thread context switch:
510 many fixed, static and dynamic MPU regions may be programmed simultaneously. For platforms
515 In Arm v8-M processors the MPU architecture does not allow programmed MPU regions to
517 covering the entire SRAM is programmed. When it does, a full SRAM area partitioning
520 enabled the fixed MPU region covering the entire SRAM is not programmed, thus, the static
[all …]
|
| /Zephyr-latest/boards/shields/renesas_us159_da14531evz/doc/ |
| D | index.rst | 25 The DA14531 Module contained on the shield must be programmed with a binary
|
| /Zephyr-latest/samples/sysbuild/hello_world/ |
| D | README.rst | 17 application is programmed.
|
| /Zephyr-latest/boards/beagle/beagleconnect_freedom/doc/ |
| D | index.rst | 13 of a board and a case which ships programmed and ready to be used.
|
| /Zephyr-latest/boards/norik/octopus_som/doc/ |
| D | index.rst | 94 Norik Octopus SoM can be programmed and debugged using the exposed SWD pins.
|
| /Zephyr-latest/boards/shields/mikroe_ble_tiny_click/doc/ |
| D | index.rst | 34 The DA14531 Module contained on the shield must be programmed with a binary
|
| /Zephyr-latest/boards/rakwireless/rak4631/doc/ |
| D | index.rst | 14 programmed with ZephyrRTOS.
|
| /Zephyr-latest/samples/boards/espressif/deep_sleep/ |
| D | README.rst | 18 1. ``Timer``: An RTC timer that can be programmed to trigger a wake up after
|
| /Zephyr-latest/boards/others/promicro_nrf52840/doc/ |
| D | index.rst | 57 The board is factory-programmed with Adafruit's UF2 booloader
|
| /Zephyr-latest/samples/drivers/fpga/fpga_controller/ |
| D | README.rst | 52 Once the board is programmed, the LED should alternately flash red and green.
|
| /Zephyr-latest/boards/atmel/sam/sam4s_xplained/doc/ |
| D | index.rst | 44 connected to the Segger J-Link OB chip (the AT91SAM3U4 is programmed to be
|
123
