| /hal_nxp-3.5.0/mcux/mcux-sdk/docs/ |
| D | run_a_project_using_armgcc_CN.md | 70 本章节介绍了使用J-Link GDB服务器应用运行演示应用的步骤。要执行此练习，必须完成以下两项操作：
71 - 安装J-Link软件（驱动程序和实用程序），可从www.segger.com/downloads.html 中下载。
73 - 已使用J-Link OpenSDA固件将开发板上的OpenSDA接口编程。如果您的开发板不支持OpenSDA，则需要使用单独的J-Link pod。
74 - 您需将单独的J-Link pod连接至板的调试接口。
80 配置和连接J-Link接口之后，请按照以下步骤下载和运行演示应用：
82 2. 通过OpenSDA USB连接器（在部分开发板上可能名为OSJTAG）与PC USB连接器之间的USB线缆将开发平台与PC相连。如果使用单独的J-Link调试pod，请同时将其连接至开发板的S…
91 4. 打开 J-Link GDB 服务器应用程序。假定已安装J-Link软件，转到 SEGGER 安装文件夹。例如，C:\Program Files (x86)\SEGGER\JLink_Vxxx。
100 
|
| D | run_a_project_using_armgcc.md | 73 This section describes steps to run a demo application using J-Link GDB Server application. To perf…
75 - The OpenSDA interface on your board is programmed with the J-Link OpenSDA firmware. If your board…
76 support OpenSDA, then a standalone J-Link pod is required.
77 - You have a standalone J-Link pod that is connected to the debug interface of your board.
83 After the J-Link interface is configured and connected, follow these steps to download and run the …
84 1. This board supports the J-Link debug probe. Before using it, install SEGGER software, which can …
87 connector. If using a standalone J-Link debug pod, also connect it to the SWD/JTAG connector of the…
98 4. Open the J-Link GDB Server application. Go to the SEGGER install folder. For example, C:\Program
108 …?\b/,aO=/^key/,bf=/^(?:mouse|contextmenu)|click/,T=/^(?:focusinfocus|focusoutblur… variable
68 …J(P){k.powerTip.show(this,P)},"mouseleave.powertip":function L(){k.powerTip.hide(this)},"focus.pow… argument
87 …J=this.getHeight(K),u=r.offset(),o=u.left,m=u.top,q=this.getWidth(r),F=this.getHeight(r),H=a(windo…
|
| /hal_nxp-3.5.0/mcux/mcux-sdk/components/css_pkc/doc/html/ |
| D | jquery.js | 16 …J=/(?:^|\s)hover(\.\S+)?\b/,aP=/^key/,bg=/^(?:mouse|contextmenu)|click/,T=/^(?:focusinfocus|focuso… variable
68 …J(P){k.powerTip.show(this,P)},"mouseleave.powertip":function L(){k.powerTip.hide(this)},"focus.pow… argument
87 …J=this.getHeight(K),u=r.offset(),o=u.left,m=u.top,q=this.getWidth(r),F=this.getHeight(r),H=a(windo…
|
| /hal_nxp-3.5.0/mcux/mcux-sdk/middleware/issdk/docs/issdk/SensorFusion/SensorFusion API Reference Manual/ |
| D | jquery.js | 16 …J=/\bhover(\.\S+)?\b/,aO=/^key/,bf=/^(?:mouse|contextmenu)|click/,T=/^(?:focusinfocus|focusoutblur… variable
68 …J(P){k.powerTip.show(this,P)},"mouseleave.powertip":function L(){k.powerTip.hide(this)},"focus.pow… function
|
| /hal_nxp-3.5.0/mcux/middleware/mcux-sdk-middleware-usb/host/ |
| D | usb_host_ip3516hs.h | 145 …volatile uint32_t J : 1U; /*!< Jump: 0: increment the PTD pointer. 1: enable the next PTD branchi… member
214 …volatile uint32_t J : 1U; /*!< Jump: 0: increment the PTD pointer. 1: enable the next PTD branchi… member
329 volatile uint32_t J : 1U; /*!< Jump */ member
|
| /hal_nxp-3.5.0/mcux/mcux-sdk/components/rtt/ |
| D | License.txt | 9 compatible with the RTT protocol and J-Link.
|
| /hal_nxp-3.5.0/mcux/mcux-sdk/drivers/casper/ |
| D | fsl_casper.c | 1975 uint32_t *Z1Z1, *Z2Z2, *U1, *S1, *J, *H, *V, *t0, *t1; in Jac_addition() local
1982 J = &CASPER_MEM[((2U * (N_wordlen + 4U)) + (9U * (N_wordlen + 4U))) + 4U * (N_wordlen + 4U)]; in Jac_addition()
2012 multiply_casper(J, Y2, t0); /* if (S1 == J) then Y's are the same */ in Jac_addition()
2015 CASPER_ECC_equal(&m2, S1, J); /* If S1 and J match then the Y-coordinates are the same. */ in Jac_addition()
2032 sub_casper(t0, J, S1); in Jac_addition()
2033 multiply_casper(J, H, t1); in Jac_addition()
2038 sub_casper(t0, t0, J); in Jac_addition()
2041 multiply_casper(t1, S1, J); in Jac_addition()
|
| /hal_nxp-3.5.0/mcux/mcux-sdk/ |
| D | LA_OPT_NXP_Software_License RTAudio.txt | 144 SEGGER Microcontroller - J-Link/J-Trace Software: Segger software must be used consistent with the …
|
| D | LA_OPT_NXP_Software_License.txt | 188 SEGGER Microcontroller - J-Link/J-Trace Software: Segger software must be used consistent with the …
|
