Searched refs:there (Results 126 – 150 of 446) sorted by relevance
12345678910>>...18
| /Zephyr-latest/boards/st/stm32n6570_dk/doc/ |
| D | index.rst | 133 To program the board, there are two options:
136 and executed from there.
139 there. It is not retained.
|
| /Zephyr-latest/doc/connectivity/networking/api/ |
| D | net_pkt.rst | 91 Where proto could be 0 if unknown (there is no IPPROTO_UNSPEC).
103 the headers space. If there is insufficient MTU space, the requested
189 As there are two paths, TX and RX, there are two access modes: write
228 point, it will fail because there is nothing to read at the cursor
|
| D | thread.rst | 58 documented there.
|
| D | net_timeout.rst | 41 again to determine whether the timeout has completed, or whether there is
|
| /Zephyr-latest/tests/lib/devicetree/api/ |
| D | app.overlay | 401 /* there should only be one of these */
420 /* there should only be one of these */
456 /* there should only be one of these */
465 /* there should only be one of these */
650 /* there should only be one of these */
|
| /Zephyr-latest/drivers/watchdog/ |
| D | Kconfig.nxp_fs26 | 41 there is a bad watchdog refresh, this counter is reset to 0.
|
| /Zephyr-latest/samples/subsys/usb/webusb-next/ |
| D | README.rst | 57 there is no notification from the browser, open the URL http://localhost:8001/
|
| /Zephyr-latest/boards/seeed/xiao_rp2040/doc/ |
| D | index.rst | 21 There are 14 GPIO PINs on Seeed Studio XIAO RP2040, on which there
|
| /Zephyr-latest/doc/develop/toolchains/ |
| D | iar_arm_toolchain.rst | 49 Basic icf-file support is in place, but there are still areas which are not fully
|
| /Zephyr-latest/samples/net/sockets/echo_async_select/ |
| D | README.rst | 56 there's an additional option to set for Linux to make a socket IPv6-only).
|
| /Zephyr-latest/drivers/disk/nvme/ |
| D | Kconfig | 69 This sets the maximum namespace to allocate. Note that there may
|
| /Zephyr-latest/drivers/ethernet/nxp_imx_netc/ |
| D | Kconfig | 40 do in the RX thread before yielding the processor, in case there is more
|
| /Zephyr-latest/tests/kernel/timer/timer_behavior/ |
| D | Kconfig | 36 # Use 13% on nRF platforms using the RTC timer because one tick there is
|
| /Zephyr-latest/samples/sensor/ccs811/ |
| D | README.rst | 37 After a soft reset, there is a 5-second startup period
|
| /Zephyr-latest/doc/services/logging/ |
| D | cs_stm.rst | 12 register sets) which can be independently accessed thus there is no need for locking when various
36 of data. Circular RAM buffer size is limited to 4k thus there is a risk of data overflow. If
49 …sumed that frontend provides the timestamp. Frontend utilizes a fact that there are multiple STMES…
83 There is less data written so there is less chance of data overflow in ETR buffer.
93 If TPIU is used as the output then there is no more software components needed. STPv2 stream
|
| /Zephyr-latest/scripts/ci/es_upload/ |
| D | README.md | 18 or read its source code with inline comments there.
56 either `testcases` or `recording`, so each item there becomes an independent data record
|
| /Zephyr-latest/boards/xen/xenvm/doc/ |
| D | index.rst | 76 at build time. So there are chances, that Zephyr image created with default
165 almost any ARMv8 host running in aarch64 mode, there is no guarantee, that Xen
|
| /Zephyr-latest/doc/project/ |
| D | tsc.rst | 170 there is general consensus.
171 - If there are no objections to a motion being brought forward, general
173 - Should there be any objections raised, the vote will move to email, and be
|
| /Zephyr-latest/cmake/modules/ |
| D | FindGnuLd.cmake | 41 # Since GNULD_LINKER already exists, there is no need to find it again (below).
|
| /Zephyr-latest/boards/st/nucleo_f756zg/ |
| D | nucleo_f756zg.dts | 165 * there is no way to make the part smaller.
|
| /Zephyr-latest/boards/nxp/frdm_mcxw71/ |
| D | frdm_mcxw71.dts | 118 * there is a reset gpio line but the line is
|
| /Zephyr-latest/drivers/espi/ |
| D | Kconfig.it8xxx2 | 131 # Port 80 and 81 I/O cycles share the same interrupt source and there is no
|
| /Zephyr-latest/tests/bsim/bluetooth/ll/edtt/ |
| D | README.txt | 10 In very short, there is 2 applications in this folder:
|
| /Zephyr-latest/samples/boards/nordic/battery/ |
| D | README.rst | 45 Note that in many cases where there is no voltage divider the digital
|
| /Zephyr-latest/boards/snps/nsim/arc_classic/doc/ |
| D | index.rst | 54 I.e. for the single-core ``nsim/nsim_hs5x`` platform there are
58 For the multi-core configurations there is only ``.args`` file as the multi-core configuration
61 I.e. for the multi-core ``nsim/nsim_hs5x/smp`` platform there is only
87 there might be exceptions from that, especially for newly added targets. You can check supported
270 If modification of existing nsim configuration is required or even there's a need in creation of a
|
12345678910>>...18
