Searched refs:should (Results 726 – 750 of 1262) sorted by relevance
1...<<21222324252627282930>>...51
| /Zephyr-latest/subsys/mgmt/mcumgr/transport/ |
| D | Kconfig.bluetooth | 9 # Options defined in this file should be prefixed:
|
| /Zephyr-latest/doc/services/storage/disk/ |
| D | nvme.rst | 40 Any board exposing an NVMe disk should provide a DTS overlay to enable its use within Zephyr
|
| /Zephyr-latest/dts/arm/st/f3/ |
| D | stm32f303.dtsi | 26 /* I2C clock source should always be defined,
|
| /Zephyr-latest/boards/olimex/stm32_h405/doc/ |
| D | index.rst | 152 After resetting the board, you should see the following message:
|
| /Zephyr-latest/doc/kernel/services/threads/ |
| D | nothread.rst | 78 disabled. Subsystems that are not listed here should not be expected to
|
| /Zephyr-latest/boards/vcc-gnd/yd_stm32h750vb/doc/ |
| D | index.rst | 62 Connect a USB-C cable and the board should power ON. Force the board into DFU mode
|
| /Zephyr-latest/doc/hardware/peripherals/sensor/ |
| D | fetch_and_get.rst | 23 It should be noted that calling fetch and get from multiple contexts without
|
| /Zephyr-latest/doc/develop/toolchains/ |
| D | custom_cmake.rst | 28 :file:`generic.cmake` and :file:`target.cmake` files should contain.
|
| /Zephyr-latest/drivers/adc/ |
| D | Kconfig | 32 # which should be used.
|
| /Zephyr-latest/samples/net/sockets/txtime/ |
| D | Kconfig | 59 This value should be smaller than the interval time
|
| /Zephyr-latest/modules/hal_rpi_pico/ |
| D | CMakeLists.txt | 16 # stage bootloader should be compiled.
|
| /Zephyr-latest/samples/bluetooth/direction_finding_connectionless_rx/ |
| D | README.rst | 77 network core application, the antenna matrix configuration should be stored in
|
| /Zephyr-latest/boards/nxp/mimxrt1024_evk/doc/ |
| D | index.rst | 247 Open a serial terminal, reset the board (press the SW9 button), and you should
266 should see the following message in the terminal:
|
| /Zephyr-latest/doc/services/retention/ |
| D | index.rst | 10 when a device reboots. The stored data should not persist in the event of a
11 power failure (or during some low-power modes on some devices) nor should it be
|
| /Zephyr-latest/doc/connectivity/networking/api/ |
| D | coap.rst | 51 The ``.well-known/core`` resource should be added before all other
52 resources that should be included in the responses of the ``.well-known/core``
|
| /Zephyr-latest/boards/nxp/twr_ke18f/doc/ |
| D | index.rst | 194 Open a serial terminal, reset the board (press the SW1 button), and you should
213 should see the following message in the terminal:
|
| /Zephyr-latest/boards/nxp/frdm_kw41z/doc/ |
| D | index.rst | 204 Open a serial terminal, reset the board (press the SW1 button), and you should
223 should see the following message in the terminal:
|
| /Zephyr-latest/boards/nxp/frdm_mcxn236/doc/ |
| D | index.rst | 182 Open a serial terminal, reset the board (press the RESET button), and you should
201 should see the following message in the terminal:
|
| /Zephyr-latest/boards/adi/max32666fthr/doc/ |
| D | index.rst | 187 | | | an input to power the board, but this should only be done when not using the…
228 appending ``--runner jlink`` to your ``west`` command(s). The J-Link should
|
| /Zephyr-latest/boards/nxp/frdm_kl25z/doc/ |
| D | index.rst | 191 Open a serial terminal, reset the board (press the SW1 button), and you should
210 should see the following message in the terminal:
|
| /Zephyr-latest/boards/andestech/adp_xc7k_ae350/doc/ |
| D | index.rst | 208 At first, you should run ICEman when flashing and debugging program.
261 you should see the following message in the terminal:
|
| /Zephyr-latest/drivers/net/ |
| D | Kconfig | 101 This is only necessary if a ppp connection should be
199 testing, should not be enabled for normal applications
|
| /Zephyr-latest/samples/bluetooth/hci_uart/ |
| D | README.rst | 84 If you are running :file:`btmon` you should see a brief log showing how the
112 If you are running :file:`btmon` you should see a comprehensive log showing how
|
| /Zephyr-latest/boards/arm/mps3/doc/ |
| D | index.rst | 298 Reset the board, and you should see the following message on the corresponding
313 Connect the MPS3 to your host computer using the USB port. You should see a
334 Reset the board, and you should see the following message on the corresponding
|
| /Zephyr-latest/boards/nxp/mimxrt1160_evk/doc/ |
| D | index.rst | 256 secondary core should be placed into a loop, then a debugger can be attached
339 open a serial terminal, reset the board (press the SW4 button), and you should
358 should see the following message in the terminal:
|
1...<<21222324252627282930>>...51
