Home
last modified time | relevance | path

Searched refs:serial (Results 426 – 450 of 912) sorted by relevance

1...<<11121314151617181920>>...37

/Zephyr-4.1.0/soc/ti/simplelink/cc13x2x7_cc26x2x7/
DKconfig37 Enable the serial bootloader which resides in ROM on CC13xx / CC26xx
/Zephyr-4.1.0/samples/sensor/tmp116/
DREADME.rst49 to the computer and open /dev/ttyACM0 with the below serial settings:
/Zephyr-4.1.0/dts/xtensa/nxp/
Dnxp_imx8ulp.dtsi63 lpuart7: serial@29870000 {
/Zephyr-4.1.0/boards/weact/stm32h5_core/doc/
Dindex.rst57 …- 1x OCTOSPI memory interface with on-the-fly decryption and support for serial PSRAM/NAND/NOR, Hy…
98 The Zephyr console output is assigned to the USB CDC ACM virtual serial port.
139 Run a serial host program to connect with your board:
/Zephyr-4.1.0/boards/witte/linum/doc/
Dindex.rst19 - 1 UART serial for debug
72 The LINUM-STM32H753BI used the USART1 for serial console.
326 Run a serial host program to connect with your Nucleo board.
/Zephyr-4.1.0/boards/lilygo/ttgo_t8s3/doc/
Dindex.rst33 | UART | on-chip | serial port |
61 | USB-CDC | on-chip | serial |
196 You can also open the serial monitor using the following command:
/Zephyr-4.1.0/boards/snps/iotdk/doc/
Dindex.rst98 serial output via the USB-UART on the board. To enable serial output:
100 * Open a serial port emulator (i.e. on Linux minicom, putty, screen, etc)
/Zephyr-4.1.0/boards/st/nucleo_l432kc/doc/
Dindex.rst70 - 1x SAIs (serial audio interface)
81 - Development support: serial wire debug (SWD), JTAG, Embedded Trace Macrocell*
163 then run a serial host program to connect with your Nucleo board.
/Zephyr-4.1.0/boards/ti/cc1352p7_launchpad/doc/
Dindex.rst102 are in place. Also place jumpers on the TXD and RXD signals for a serial
103 console using the XDS110 application serial port.
151 serial device can be found. For example, :code:`/dev/ttyACM0`.
/Zephyr-4.1.0/boards/st/nucleo_l433rc_p/doc/
Dindex.rst70 - 1x SAI (serial audio interface)
82 - Development support: serial wire debug (SWD), JTAG, Embedded Trace Macrocell*
166 then run a serial host program to connect with your Nucleo board.
/Zephyr-4.1.0/boards/shields/mikroe_wifi_bt_click/doc/
Dindex.rst47 site, connect the J1 of the board to a serial-to-USB converter of your
94 See the example below for lpcxpresso55s69 board using Mikrobus serial:
/Zephyr-4.1.0/samples/boards/nordic/nrf53_sync_rtc/
DREADME.rst35 Open a serial terminals (for example Minicom or PuTTY) and connect the board with the
43 …llowing messages (one for master and one for remote) will appear on the corresponding serial ports:
/Zephyr-4.1.0/boards/silabs/dev_kits/xg24_dk2601b/doc/
Dindex.rst115 Open a serial terminal (minicom, putty, etc.) with the following settings:
122 Reset the board and you'll see the following message on the corresponding serial port
/Zephyr-4.1.0/dts/riscv/sifive/
Driscv32-fe310.dtsi191 uart0: serial@10013000 {
199 uart1: serial@10023000 {
/Zephyr-4.1.0/boards/st/stm32l4r9i_disco/doc/
Dindex.rst77 USB port, then run a serial host program to connect with the board. For example:
91 You should see the following message in the serial host program:
/Zephyr-4.1.0/boards/adafruit/trinket_m0/doc/
Dindex.rst68 serial port that echos characters back to the host PC.
92 #. Connect a 3.3 V USB to serial adapter to the board and to the
/Zephyr-4.1.0/boards/nxp/imx8mn_evk/doc/
Dindex.rst61 | UART | on-chip | serial port |
82 This board configuration uses a single serial communication channel with the
/Zephyr-4.1.0/dts/arm/st/l5/
Dstm32l5.dtsi264 usart1: serial@40013800 {
273 usart2: serial@40004400 {
282 usart3: serial@40004800 {
291 uart4: serial@40004c00 {
300 uart5: serial@40005000 {
309 lpuart1: serial@40008000 {
/Zephyr-4.1.0/dts/arm/renesas/rz/rzg/
Dr9a08g045.dtsi420 scif0: serial@4004b800 {
428 scif1: serial@4004bc00 {
436 scif2: serial@4004c000 {
444 scif3: serial@4004c400 {
452 scif4: serial@4004c800 {
460 scif5: serial@4004e000 {
/Zephyr-4.1.0/dts/arm/st/h7/
Dstm32h7.dtsi288 usart1: serial@40011000 {
296 usart2: serial@40004400 {
304 usart3: serial@40004800 {
312 uart4: serial@40004c00 {
320 uart5: serial@40005000 {
328 usart6: serial@40011400 {
336 uart7: serial@40007800 {
344 uart8: serial@40007c00 {
353 lpuart1: serial@58000c00 {
/Zephyr-4.1.0/subsys/mgmt/mcumgr/transport/
DKconfig.shell50 Time (in msec) after receiving a valid MCUmgr header on the serial
/Zephyr-4.1.0/soc/ti/simplelink/cc13x2_cc26x2/
DKconfig36 Enable the serial bootloader which resides in ROM on CC13xx / CC26xx
/Zephyr-4.1.0/doc/connectivity/networking/api/
Dppp.rst16 between two nodes. PPP is used over many types of serial links since IP packets
/Zephyr-4.1.0/subsys/retention/
DKconfig51 e.g. button-less bootloader serial recovery mode entering from the
/Zephyr-4.1.0/drivers/ethernet/
DKconfig.adin211119 via a serial peripheral inter-face (SPI).

1...<<11121314151617181920>>...37