Searched refs:serial (Results 376 – 400 of 912) sorted by relevance
1...<<11121314151617181920>>...37
| /Zephyr-4.1.0/dts/arm/st/l0/ |
| D | stm32l051.dtsi | 35 usart1: serial@40013800 {
|
| /Zephyr-4.1.0/dts/arm/st/l4/ |
| D | stm32l412.dtsi | 65 usart3: serial@40004800 {
|
| D | stm32l433.dtsi | 53 usart3: serial@40004800 {
|
| /Zephyr-4.1.0/dts/arm64/rockchip/ |
| D | rk3568.dtsi | 80 uart2: serial@fe660000 {
|
| D | rk3588s.dtsi | 94 uart2: serial@feb50000 {
|
| D | rk3399.dtsi | 86 uart2: serial@ff1a0000 {
|
| /Zephyr-4.1.0/dts/arm/st/f0/ |
| D | stm32f042.dtsi | 24 usart2: serial@40004400 {
|
| D | stm32f051.dtsi | 13 usart2: serial@40004400 {
|
| D | stm32f030X8.dtsi | 21 usart2: serial@40004400 {
|
| /Zephyr-4.1.0/dts/arm/st/g4/ |
| D | stm32g491.dtsi | 72 uart5: serial@40005000 {
|
| /Zephyr-4.1.0/boards/nxp/mimxrt1050_evk/doc/ |
| D | index.rst | 124 | UART | on-chip | serial port-polling; |
125 | | | serial port-interrupt |
357 microcontroller as a usb-to-serial adapter for the serial console. Check that
363 Use the following settings with your serial terminal of choice (minicom, putty,
381 Open a serial terminal, reset the board (press the SW4 button), and you should
399 Open a serial terminal, step through the application in your debugger, and you
|
| /Zephyr-4.1.0/boards/arduino/nano_33_iot/doc/ |
| D | index.rst | 64 serial port that echos characters back to the host PC.
88 #. Connect a 3.3 V USB to serial adapter to the board and to the
|
| /Zephyr-4.1.0/boards/arm/fvp_baser_aemv8r/doc/ |
| D | aarch64.rst | 45 | PL011 UART | on-chip | serial port |
69 This board configuration uses a single serial communication channel with the
|
| /Zephyr-4.1.0/doc/hardware/peripherals/ |
| D | w1.rst | 9 1-Wire is a low speed half-duplex serial bus using only a single wire plus
36 temperature sensors and serial memories.
|
| /Zephyr-4.1.0/dts/riscv/telink/ |
| D | telink_b91.dtsi | 140 uart0: serial@80140080 {
148 uart1: serial@801400C0 {
|
| /Zephyr-4.1.0/boards/nxp/imx91_evk/doc/ |
| D | index.rst | 69 | UART | on-chip | serial port |
83 This board configuration uses a single serial communication channel with the
|
| /Zephyr-4.1.0/boards/01space/esp32c3_042_oled/doc/ |
| D | index.rst | 18 * WS2812B RGB serial LED
31 The ESP32-C3 does not have native USB, it has an on-chip USB-serial converter
|
| /Zephyr-4.1.0/scripts/tests/twister/ |
| D | test_handlers.py | 20 from serial import SerialException
775 serial=None,
826 serial=None,
882 serial=mock.Mock(),
890 serial=mock.Mock(),
938 serial = mock.Mock(name='dummy_serial')
940 mock.Mock(available=0, serial=serial, serial_pty=None),
941 mock.Mock(available=0, serial=None, serial_pty=serial),
944 serial=mock.Mock('another_serial'),
1438 serial='dummy serial',
|
| /Zephyr-4.1.0/samples/subsys/modbus/tcp_gateway/src/ |
| D | main.c | 24 .serial = {
|
| /Zephyr-4.1.0/boards/shields/mikroe_eth3_click/doc/ |
| D | index.rst | 11 16Kbyte FIFO Buffer and SPI serial interface.
|
| /Zephyr-4.1.0/dts/arm/ti/ |
| D | am62x_m4.dtsi | 58 uart0: serial@4a00000 {
|
| /Zephyr-4.1.0/dts/riscv/lowrisc/ |
| D | opentitan_earlgrey.dtsi | 82 uart0: serial@40000000{
|
| /Zephyr-4.1.0/drivers/ethernet/ |
| D | Kconfig.lan865x | 18 via a serial peripheral inter-face (SPI).
|
| /Zephyr-4.1.0/dts/arm/st/f7/ |
| D | stm32f7.dtsi | 254 usart1: serial@40011000 {
263 usart2: serial@40004400 {
272 usart3: serial@40004800 {
281 uart4: serial@40004c00 {
290 uart5: serial@40005000 {
299 usart6: serial@40011400 {
308 uart7: serial@40007800 {
317 uart8: serial@40007c00 {
|
| /Zephyr-4.1.0/boards/ti/cc1352p1_launchxl/doc/ |
| D | index.rst | 101 are in place. Also place jumpers on the TXD and RXD signals for a serial
102 console using the XDS110 application serial port.
145 serial device can be found. For example, :code:`/dev/ttyACM0`.
|
1...<<11121314151617181920>>...37
