Home
last modified time | relevance | path

Searched refs:number (Results 101 – 125 of 1002) sorted by relevance

12345678910>>...41

/Zephyr-latest/soc/silabs/silabs_s1/efr32fg1p/
DKconfig.defconfig7 # must be >= the highest interrupt number used
/Zephyr-latest/soc/silabs/silabs_s1/efr32mg12p/
DKconfig.defconfig7 # must be >= the highest interrupt number used
/Zephyr-latest/soc/silabs/silabs_s1/efm32pg12b/
DKconfig.defconfig7 # must be >= the highest interrupt number used
/Zephyr-latest/soc/silabs/silabs_s1/efr32fg13p/
DKconfig.defconfig7 # must be >= the highest interrupt number used
/Zephyr-latest/soc/silabs/silabs_s0/efm32wg/
DKconfig.defconfig7 # must be >= the highest interrupt number used
/Zephyr-latest/tests/drivers/adc/adc_api/boards/
Dstm32u5a9j_dk.overlay9 /* adjust channel number according to pinmux in board.dts */
Dstm32g081b_eval.overlay9 /* adjust channel number according to pinmux in board.dts */
/Zephyr-latest/samples/drivers/adc/adc_dt/boards/
Dnucleo_wba52cg.overlay9 /* adjust channel number according to pinmux in board.dts */
/Zephyr-latest/soc/espressif/esp32/
DKconfig.mac10 Configure the number of universally administered (by IEEE) MAC addresses.
12 derived from a single base MAC address. If the number of universal MAC addresses is four,
15 to the final octet of the base MAC address. If the number of universal MAC addresses is two,
/Zephyr-latest/doc/kernel/timing_functions/
Dindex.rst35 5. Call :c:func:`timing_cycles_get` to get the number of timer cycles
38 6. Call :c:func:`timing_cycles_to_ns` with total number of cycles
39 to convert number of cycles to nanoseconds.
/Zephyr-latest/drivers/sensor/microchip/mchp_tach_xec/
DKconfig21 This value represents the number of Tach edges that
22 will be used to determine the interval for which the number of
/Zephyr-latest/samples/drivers/w1/scanner/
DREADME.rst5 Scan for 1-Wire devices and print their family ID and serial number.
11 scan routine once and prints the family id as well as serial number of the
/Zephyr-latest/drivers/ethernet/
DKconfig.cyclonev18 A higher number allows for more packets to be queued which may
31 Received packets are spread across the required number of fragment
/Zephyr-latest/samples/boards/nordic/system_off/
DREADME.rst17 By selecting ``CONFIG_APP_USE_RETAINED_MEM=y`` state related to number of boots,
18 number of times system off was entered, and total uptime since initial power-on
/Zephyr-latest/subsys/bluetooth/
DKconfig.adv31 int "Maximum number of simultaneous advertising sets"
35 Maximum number of simultaneous Bluetooth advertising sets
80 int "Maximum number of simultaneous periodic advertising syncs"
84 Maximum number of simultaneous periodic advertising syncs supported.
/Zephyr-latest/soc/silabs/silabs_s1/efm32pg1b/
DKconfig.defconfig7 # must be >= the highest interrupt number used
/Zephyr-latest/soc/silabs/silabs_s0/efm32hg/
DKconfig.defconfig8 # must be >= the highest interrupt number used
/Zephyr-latest/samples/userspace/syscall_perf/
DREADME.rst21 Both threads are showing the number of core clock cycles and the number of
/Zephyr-latest/drivers/usb/udc/
DKconfig.stm3232 int "STM32 UDC driver maximum number of ISR event messages"
36 Maximum number of messages for handling of STM32 USBD ISR events.
/Zephyr-latest/drivers/input/
DKconfig.analog_axis37 int "Maximum number of axes supported in the settings."
40 Maximum number of axes that can have calibration value saved in
/Zephyr-latest/soc/nxp/imx/imx7d/
DKconfig.defconfig9 # must be >= the highest interrupt number used
/Zephyr-latest/soc/st/stm32/stm32l1x/
DKconfig.defconfig.stm32l151xc8 # Based on stm32cube number of interrupts+1, not datasheet
/Zephyr-latest/soc/espressif/esp32s3/
DKconfig.mac10 Configure the number of universally administered (by IEEE) MAC addresses.
13 If the number of universal MAC addresses is four, all four interfaces (WiFi station, WiFi softap,
16 If the number of universal MAC addresses is two, only two interfaces (WiFi station and Bluetooth)
/Zephyr-latest/soc/silabs/silabs_s2/efr32bg27/
DKconfig.defconfig7 # must be >= the highest interrupt number used
/Zephyr-latest/soc/nxp/lpc/lpc11u6x/
DKconfig.defconfig12 # must be >= the highest interrupt number used

12345678910>>...41