Searched refs:low (Results 826 – 850 of 857) sorted by relevance
1...<<3132333435
| /Zephyr-latest/doc/releases/ |
| D | release-notes-2.0.rst | 33 including version 5.1 permits sufficiently low encryption key length
439 setup, RSSI, low-latency ULL processing of messages, nRF52811 IC BLE
454 - :zephyr_file:`scripts/dts/dtlib.py` -- a low-level :file:`.dts` parsing
975 * :github:`16739` - spi: stm32: pinmux: default configuration does not opt for low power consumption
1427 * :github:`8978` - soc: Intel S1000: add low power memory management support
|
| D | release-notes-1.9.rst | 356 * ``ZEP-2510`` - BT: CONFIG_BT_HCI_TX_STACK_SIZE appears to be too low for BT_SPI
|
| D | release-notes-2.2.rst | 1102 * :github:`20125` - Add system call to enter low power mode and reduce latency for deep sleep entry
1214 * :github:`9904` - System timer handling with low-frequency timers
1235 * :github:`6157` - SMP lacks low-power idle
|
| D | release-notes-3.7.rst | 1136 * Added low power comparator driver (:dtcompatible:`nxp,lpcmp`).
1224 * Added support to put TX and RX pins into low power mode when UART is not active.
1500 * Added PPP low level packet capture support.
1919 * Updated HAL to version v5.1, which has new SoCs low-level files.
|
| D | release-notes-3.5.rst | 1257 * new property: ``line-idle-low``
1423 * new property: ``enable-low-power-32k``
1837 * new property: ``io-low-port``
|
| D | release-notes-2.5.rst | 997 * :github:`31989` - nrfx_uarte serial driver does not go to low power mode after setting off state
1772 * :github:`26975` - Control never returns from stm32_i2c_msg_write(), when SCL is pulled low perman…
1799 * :github:`26330` - tcp: low bulk receive performance due to window handling
1929 * :github:`12239` - BLE400 / nRF51822 (nRF51) PWM clock too low (servo-motor example)
|
| D | release-notes-3.4.rst | 965 some cards require the SPI clock switch to low when not active
1376 the system on which low power states can be used.
|
| D | release-notes-3.6.rst | 196 * Added support for low power on G1120B0MIPI using RT595.
556 * Fixed ESP32S3 low frequency PWM issue.
|
| D | migration-guide-3.6.rst | 442 low power modes is identified by **stm32_lp_tick_source** in the device tree as follows.
|
| D | release-notes-3.0.rst | 939 * :github:`42161` - samples/compression/l4z: Expected RAM size for correct execution is too low
1262 * :github:`39569` - [ESP32] crash when trying to set a low cpu clock frequency
|
| D | release-notes-4.0.rst | 262 * added additional support to Wakeup from low power modes
1441 * Synced HAL to version v5.1.4 to update SoCs low level files, RF libraries and
|
| D | release-notes-3.1.rst | 713 window availability. This allows to improve throughput greatly in low-buffer
781 assignments in different system states, such as active and low-power
1649 …:github:`43794` - BMI160 Driver: Waiting time between SPI activation and reading CHIP IP is too low
|
| D | release-notes-1.13.rst | 634 * :github:`6730` - ARMv8-M: internal low-level (TrustZone) API & implementation for configuring IRQ…
|
| D | release-notes-2.1.rst | 610 * :github:`20225` - [TOPIC-GPIO] sam\_e70\_xplained fails 2-pin active-low pull test
|
| /Zephyr-latest/kernel/ |
| D | Kconfig | 313 performance for single threads and very low code size.
342 in almost all circumstances with very low constant factor.
|
| /Zephyr-latest/doc/project/ |
| D | dev_env_and_tools.rst | 275 * - :guilabel:`priority: {high|medium|low}`
|
| /Zephyr-latest/doc/build/dts/ |
| D | macros.bnf | 176 ; output-low;
|
| D | bindings-syntax.rst | 203 - "low-speed"
|
| /Zephyr-latest/boards/espressif/esp32_ethernet_kit/doc/ |
| D | index.rst | 394 low, turning the clock output off. After power-on you can control
|
| /Zephyr-latest/boards/espressif/esp_wrover_kit/doc/ |
| D | index.rst | 74 | | low-power consumption while the chip is in Deep-sleep mode. |
|
| /Zephyr-latest/modules/hal_nordic/nrfx/ |
| D | Kconfig | 21 bool "Two stage start sequence of the low frequency clock"
|
| /Zephyr-latest/doc/develop/test/ |
| D | ztest.rst | 433 is much too low and it is recommended to increase it to 100 kHz.
|
| /Zephyr-latest/drivers/ethernet/ |
| D | eth_sam_gmac.c | 2357 gmac->GMAC_TSL = tm->_sec.low & 0xffffffff; in ptp_clock_sam_gmac_set()
|
| /Zephyr-latest/arch/ |
| D | Kconfig | 18 # Should be 'select'ed by low-level symbols like SOC_SERIES_* or, lacking that,
|
| /Zephyr-latest/doc/connectivity/bluetooth/api/audio/ |
| D | bluetooth-le-audio-arch.rst | 942 The main purpose of the service is to offload scanning from low power peripherals to e.g. phones
|
1...<<3132333435
