Searched refs:BOOT0 (Results 1 – 25 of 28) sorted by relevance
12
| /Zephyr-latest/boards/vcc-gnd/yd_stm32h750vb/doc/ |
| D | index.rst | 68 pattern, which can be triggered by using the BOOT0 button.
83 by keeping the BOOT0 switch pressed while pressing and releasing the RST switch.
|
| /Zephyr-latest/boards/others/stm32f401_mini/doc/ |
| D | index.rst | 95 pattern, which can be triggered by using the BOOT0 pin, which on this board
114 by setting the BOOT0 dip switch position to ON. Reset the board with the NRST button.
|
| /Zephyr-latest/boards/weact/mini_stm32h743/doc/ |
| D | index.rst | 151 1. Press and hold the BOOT0 key.
152 2. While still holding the BOOT0 key, press and release the RESET key.
153 3. Wait for 0.5 seconds, then release the BOOT0 key.
|
| /Zephyr-latest/boards/weact/mini_stm32h7b0/doc/ |
| D | index.rst | 152 1. Press and hold the BOOT0 key.
153 2. While still holding the BOOT0 key, press and release the RESET key.
154 3. Wait for 0.5 seconds, then release the BOOT0 key.
|
| /Zephyr-latest/boards/weact/blackpill_f401cc/doc/ |
| D | index.rst | 107 pattern, which can be triggered by using the BOOT0 pin.
125 by keeping the BOOT0 switch pressed while pressing and releasing the NRST switch.
|
| /Zephyr-latest/boards/weact/blackpill_f401ce/doc/ |
| D | index.rst | 112 pattern, which can be triggered by using the BOOT0 pin.
130 by keeping the BOOT0 switch pressed while pressing and releasing the NRST switch.
|
| /Zephyr-latest/boards/weact/blackpill_f411ce/doc/ |
| D | index.rst | 112 pattern, which can be triggered by using the BOOT0 pin.
130 by keeping the BOOT0 switch pressed while pressing and releasing the NRST switch.
|
| /Zephyr-latest/boards/weact/stm32f405_core/doc/ |
| D | index.rst | 109 pattern, which can be triggered by using the BOOT0 pin.
127 by keeping the BOOT0 switch pressed while pressing and releasing the NRST switch.
|
| /Zephyr-latest/boards/weact/stm32g431_core/doc/ |
| D | index.rst | 64 - BUTTON (BOOT0) : PB8
115 keeping the BOOT0 switch pressed while pressing and releasing the NRST switch.
|
| /Zephyr-latest/boards/96boards/wistrio/doc/ |
| D | 96b_wistrio.rst | 131 which can be triggered by using the BOOT0 pin. The ROM bootloader supports
144 - Connect BOOT0 to VDD (link pin 1 and 2 on J12)
|
| /Zephyr-latest/boards/96boards/argonkey/doc/ |
| D | index.rst | 163 which can be triggered by using the BOOT0 pin. The ROM bootloader supports
188 - Connect BOOT0 to 1V8 (link P2.1 to P3.30)
|
| /Zephyr-latest/boards/ronoth/lodev/ |
| D | ronoth_lodev.dts | 59 /* <5 0 - - 0>, BOOT0 */
|
| /Zephyr-latest/boards/others/stm32f030_demo/doc/ |
| D | index.rst | 26 - 2-way jumper (BOOT0)
|
| /Zephyr-latest/boards/96boards/carbon/doc/ |
| D | stm32f401xe.rst | 120 - BUTTON = BOOT0 (SW1)
252 pattern, which can be triggered by using the BOOT0 pin. The ROM bootloader
270 The board should power ON. Force the board into DFU mode by keeping the BOOT0
|
| /Zephyr-latest/boards/st/sensortile_box/doc/ |
| D | index.rst | 128 while keeping the BOOT0 button pressed.
147 While pressing the BOOT0 button, connect the
|
| /Zephyr-latest/boards/96boards/aerocore2/doc/ |
| D | index.rst | 262 pattern, which can be triggered by using the BOOT0 pin. The ROM bootloader
280 The board should power ON. Force the board into DFU mode by keeping the BOOT0
|
| /Zephyr-latest/boards/others/stm32f103_mini/doc/ |
| D | index.rst | 126 pattern, which can be triggered by using the BOOT0 pin.
|
| /Zephyr-latest/boards/ronoth/lodev/doc/ |
| D | index.rst | 67 6 BOOT0
|
| D | s76s.rst | 91 28 PC8 59 BOOT0
106 BOOT0 I - - …
|
| /Zephyr-latest/boards/makerbase/mks_canable_v20/doc/ |
| D | index.rst | 63 - CAN_RX/BOOT0 : PB8
|
| /Zephyr-latest/boards/96boards/neonkey/doc/ |
| D | index.rst | 157 1. Connect BOOT0 to VDD (link JTAG pins 1 and 5 on P4 header)
|
| /Zephyr-latest/boards/arduino/giga_r1/doc/ |
| D | index.rst | 124 holding the ``BOOT0`` button, this also supports USB-DFU but can only
|
| /Zephyr-latest/boards/st/b_u585i_iot02a/doc/ |
| D | index.rst | 360 Ensure U23 BOOT0 switch is set to 1 (switch is on the left, assuming you read
361 "BOOT0" silkscreen label from left to right). You need to press "Reset" (B2 RST
|
| /Zephyr-latest/boards/st/sensortile_box_pro/doc/ |
| D | index.rst | 255 by powering up (or reset) the board while keeping the BOOT0 button pressed.
280 While pressing the BOOT0 button, connect the USB-C cable to the USB OTG SensorTile.box PRO
|
| /Zephyr-latest/boards/seeed/lora_e5_mini/doc/ |
| D | index.rst | 148 Also, note that on the module the ``BOOT0`` pin of the SOC is not accessible,
|
12
