Searched refs:INTENSET (Results 1 – 13 of 13) sorted by relevance
304 RTC0->INTENSET.reg = RTC_MODE0_INTENSET_CMP0; in sys_clock_driver_init()309 RTC0->INTENSET.reg = RTC_MODE0_INTENSET_OVF; in sys_clock_driver_init()
144 regs->INTENSET.reg = SERCOM_USART_INTENSET_TXC; in uart_sam0_dma_tx_done()287 regs->INTENSET.reg = SERCOM_USART_INTENSET_RXC; in uart_sam0_dma_rx_done()347 regs->INTENSET.reg = SERCOM_USART_INTENSET_RXC; in uart_sam0_rx_timeout()804 regs->INTENSET.reg = SERCOM_USART_INTENSET_DRE in uart_sam0_irq_tx_enable()822 return (regs->INTFLAG.bit.DRE != 0) && (regs->INTENSET.bit.DRE != 0); in uart_sam0_irq_tx_ready()831 return (dev_data->txc_cache != 0) && (regs->INTENSET.bit.TXC != 0); in uart_sam0_irq_tx_complete()839 regs->INTENSET.reg = SERCOM_USART_INTENSET_RXC; in uart_sam0_irq_rx_enable()882 return (regs->INTENSET.reg & regs->INTFLAG.reg) != 0; in uart_sam0_irq_is_pending()891 regs->INTENSET.reg |= SERCOM_USART_INTENCLR_ERROR; in uart_sam0_irq_err_enable()1072 regs->INTENSET.reg = SERCOM_USART_INTENSET_RXC; in uart_sam0_rx_enable()
592 config->base->INTENSET |= USART_INTENSET_STARTEN_MASK; in mcux_flexcomm_uart_rx_enable()
259 i2c->INTENSET.reg = SERCOM_I2CM_INTENSET_MB; in i2c_sam0_dma_write_done()351 i2c->INTENSET.reg = SERCOM_I2CM_INTENSET_SB; in i2c_sam0_dma_read_done()484 i2c->INTENSET.reg = SERCOM_I2CM_INTENSET_ERROR; in i2c_sam0_transfer()492 i2c->INTENSET.reg = SERCOM_I2CM_INTENSET_MB; in i2c_sam0_transfer()498 i2c->INTENSET.reg = SERCOM_I2CM_INTENSET_SB; in i2c_sam0_transfer()506 i2c->INTENSET.reg = SERCOM_I2CM_INTENSET_MB; in i2c_sam0_transfer()
178 tc->INTENSET.reg = TC_INTFLAG_MC1; in counter_sam0_tc32_relative_alarm()209 tc->INTENSET.reg = TC_INTFLAG_MC1; in counter_sam0_tc32_set_alarm()255 tc->INTENSET.reg = TC_INTFLAG_MC0; in counter_sam0_tc32_set_top_value()
210 WDT_REGS->INTENSET.reg = WDT_INTENSET_EW; in wdt_sam0_install_timeout()
208 wrapper->INTENSET = 1UL; in usbhs_enable_core()
271 EIC->INTENSET.reg = mask; in sam0_eic_enable_interrupt()
92 enabled through INTENSET register. The case when these events are generated93 by EVTEN but without interrupts enabled through INTENSET is not handled.
155 uint32_t reg_intenset = rtc->INTENSET; in rtc_ticks_to_next_event_get()
475 adc->INTENSET.reg = ADC_INTENSET_RESRDY; in adc_sam0_init()
269 regs->INTENSET.reg = USB_DEVICE_INTENSET_EORST; in usb_dc_attach()
1038 if (NRF_USBD->INTENSET & USBD_INTEN_SOF_Msk) { in nrf_usbd_common_irq_handler()
