Searched refs:speed (Results 1 – 18 of 18) sorted by relevance
| /hal_infineon-3.6.0/mtb-pdl-cat1/drivers/source/ |
| D | cy_ephy.c | 188 …if ((config->speed == ((uint32_t)CY_EPHY_SPEED_AUTO)) || (config->duplex == ((uint32_t)CY_EPHY_DUP… in Cy_EPHY_Configure()
213 if( config->speed == ((uint32_t)CY_EPHY_SPEED_100)) in Cy_EPHY_Configure()
217 …else if ((config->speed == ((uint32_t)CY_EPHY_SPEED_1000)) && ((bmsr & PHYBMSR_EXT_STATUS_Msk) != … in Cy_EPHY_Configure()
222 else if( config->speed == ((uint32_t)CY_EPHY_SPEED_10)) in Cy_EPHY_Configure()
358 lpConfig->speed = (uint32_t)CY_EPHY_SPEED_10; in Cy_EPHY_getLinkPartnerCapabilities()
369 lpConfig->speed = (uint32_t)CY_EPHY_SPEED_1000; in Cy_EPHY_getLinkPartnerCapabilities()
374 lpConfig->speed = (uint32_t)CY_EPHY_SPEED_1000; in Cy_EPHY_getLinkPartnerCapabilities()
383 lpConfig->speed = (uint32_t)CY_EPHY_SPEED_100; in Cy_EPHY_getLinkPartnerCapabilities()
388 lpConfig->speed = (uint32_t)CY_EPHY_SPEED_100; in Cy_EPHY_getLinkPartnerCapabilities()
393 lpConfig->speed = (uint32_t)CY_EPHY_SPEED_10; in Cy_EPHY_getLinkPartnerCapabilities()
[all …]
|
| D | cy_seglcd.c | 84 #define CY_SEGLCD_IS_SPEED_VALID(speed) ((CY_SEGLCD_SPEED_LOW == (speed)) || \ argument
85 (CY_SEGLCD_SPEED_HIGH == (speed)))
93 …define CY_SEGLCD_IS_BIAS_4_5_SUPPORTED(base,speed) ((CY_SEGLCD_REV_1(base)) ? (CY_SEGLCD_SPEED_HIG… argument
95 #define CY_SEGLCD_IS_BIAS_VALID(base,bias,speed) ((CY_SEGLCD_BIAS_HALF == (bias)) || \ argument
97 (CY_SEGLCD_IS_BIAS_4_5_SUPPORTED(base,speed) && (CY_SEGLCD_BIAS_FOURTH == (bias))) || \
98 (CY_SEGLCD_IS_BIAS_4_5_SUPPORTED(base,speed) && (CY_SEGLCD_BIAS_FIFTH == (bias))))
384 CY_ASSERT_L3(CY_SEGLCD_IS_SPEED_VALID(config->speed)); in Cy_SegLCD_Init()
387 CY_ASSERT_L3(CY_SEGLCD_IS_BIAS_VALID (base, config->bias, config->speed)); in Cy_SegLCD_Init()
394 …uint32_t locCheck = ((CY_SEGLCD_SPEED_LOW == config->speed) && (CY_SEGLCD_REV_1(base))) ? (CY_SEGL… in Cy_SegLCD_Init()
409 LCD_CONTROL(base) = _VAL2FLD(LCD_CONTROL_LCD_MODE, config->speed) | in Cy_SegLCD_Init()
|
| /hal_infineon-3.6.0/mtb-template-cat1/files/templates/cat1b/COMPONENT_MTB/COMPONENT_CM33/scripts/ |
| D | launch_app_from_idle_Debug.tcl | 20 adapter speed 500
|
| D | launch_app_from_idle_Release.tcl | 20 adapter speed 500
|
| /hal_infineon-3.6.0/XMCLib/drivers/inc/ |
| D | xmc_eth_phy.h | 96 XMC_ETH_LINK_SPEED_t speed; /**< ETH speed: 100M or 10M? */ member
|
| D | xmc_eth_mac.h | 1274 XMC_ETH_LINK_SPEED_t speed, in XMC_ETH_MAC_SetLink() argument
1279 (uint32_t)speed | (uint32_t)duplex; in XMC_ETH_MAC_SetLink()
|
| D | xmc_usbh.h | 248 uint32_t speed : 2; /**< USB Host Port speed setting (ARM_USB_SPEED_xxx) */ member
|
| D | xmc_usbd.h | 346 uint32_t speed : 2; /**< USB Device speed */ member
|
| D | xmc_usbd_regs.h | 1850 uint8_t speed; /**< Device Speed 0: Unknown, 1: LS, 2:FS, 3: HS */ member
|
| /hal_infineon-3.6.0/mtb-pdl-cat1/drivers/include/ |
| D | cy_ephy.h | 297 uint32_t speed; /**< speed */ member
|
| D | cy_seglcd.h | 461 cy_en_seglcd_speed_t speed; /**< Speed mode selection, see: #cy_en_seglcd_speed_t. */ member
|
| /hal_infineon-3.6.0/XMCLib/drivers/src/ |
| D | xmc_eth_phy_ksz8031rnl.c | 156 if (config->speed == XMC_ETH_LINK_SPEED_100M) in XMC_ETH_PHY_Init()
|
| D | xmc_eth_phy_ksz8081rnb.c | 156 if (config->speed == XMC_ETH_LINK_SPEED_100M) in XMC_ETH_PHY_Init()
|
| D | xmc_eth_phy_dp83848.c | 173 if (config->speed == XMC_ETH_LINK_SPEED_100M) in XMC_ETH_PHY_Init()
|
| D | xmc_usbh.c | 702 port_state.speed = XMC_USBH_SPEED_FULL; in XMC_USBH_PortGetState()
|
| D | xmc_usbd.c | 1243 state.speed = XMC_USBD_SPEED_FULL; in XMC_USBD_DeviceGetState()
|
| /hal_infineon-3.6.0/mtb-pdl-cat1/drivers/third_party/ethernet/include/ |
| D | cedi.h | 1157 CEDI_IfSpeed speed; member
|
| /hal_infineon-3.6.0/mtb-pdl-cat1/drivers/third_party/ethernet/src/ |
| D | edd.c | 4102 lpAbl->ablInfo.sgmLpAbl.speed = in emacGetLpAbilityPage()
|
