Searched refs:P4 (Results 1 – 21 of 21) sorted by relevance
| /Zephyr-latest/tests/drivers/i2c/i2c_target_api/boards/ |
| D | mr_canhubk3.overlay | 7 /* Connect P3.2 <-> P4.3 and P3.3 <-> P4.4 */
|
| /Zephyr-latest/tests/drivers/eeprom/api/boards/ |
| D | mr_canhubk3.overlay | 7 /* Connect I2C0 (connector P4) to the external eeprom Microchip AT24C01C-XHM */
|
| /Zephyr-latest/tests/bluetooth/controller/ctrl_sw_privacy_unit/src/ |
| D | main.c | 31 #define BT_ADDR_INIT(P0, P1, P2, P3, P4, P5) \ argument
32 (&(bt_addr_t){ { P0, P1, P2, P3, P4, P5 } })
|
| /Zephyr-latest/include/zephyr/dt-bindings/pinctrl/ |
| D | ifx_cat1-pinctrl.h | 78 #define P4 CYHAL_PORT_4 macro
|
| /Zephyr-latest/boards/96boards/neonkey/doc/ |
| D | index.rst | 157 1. Connect BOOT0 to VDD (link JTAG pins 1 and 5 on P4 header)
180 For flashing via SWD debug port, 0.1" male header must be soldered at P4
184 be connected to the P4 header using its flying leads and its 20 Pin
|
| /Zephyr-latest/boards/nordic/thingy52/doc/ |
| D | index.rst | 140 The pins can be found on the P4 and P6 connectors. The system UART console
175 The external I2C bus (I2C_1) can be found on the P4 header and the P5 and P7
189 This is the pinout of the P4 pin header. Some of the SOC GPIO pins and I2C GPIO
|
| /Zephyr-latest/boards/nxp/mr_canhubk3/doc/ |
| D | index.rst | 216 on corresponding connectors ``P4``, ``P3``.
223 P4.3 PTD14 LPI2C0_SCL
224 P4.4 PTD13 LPI2C0_SDA
227 The accompanying display board can be connected to ``lpi2c0`` via connector ``P4``.
|
| /Zephyr-latest/boards/bbc/microbit_v2/ |
| D | bbc_microbit_v2.dts | 86 <4 0 &gpio0 28 0>, /* P4 */
|
| /Zephyr-latest/boards/seeed/xiao_rp2040/doc/ |
| D | index.rst | 93 - SPI0_RX : P4
|
| /Zephyr-latest/boards/adafruit/qt_py_rp2040/doc/ |
| D | index.rst | 94 - SPI0_RX : P4
|
| /Zephyr-latest/boards/bbc/microbit/ |
| D | bbc_microbit.dts | 87 <4 0 &gpio0 5 0>, /* P4, Analog in, LED Col 2 */
|
| /Zephyr-latest/boards/waveshare/rp2040_zero/doc/ |
| D | index.rst | 91 - I2C0_SDA : P4
|
| /Zephyr-latest/boards/madmachine/mm_feather/doc/ |
| D | index.rst | 95 | P4 | GPIO_AD_B1_11 | D4 | GPIO1_IO27 | | |
|
| /Zephyr-latest/boards/madmachine/mm_swiftio/doc/ |
| D | index.rst | 75 | P4 | GPIO_B1_14 | D4 | GPIO2_IO30 | | |
|
| /Zephyr-latest/boards/96boards/argonkey/doc/ |
| D | index.rst | 202 Select a commercial JTAG/SWD h/w tool and connect it to ArgonKey P4 connector.
|
| /Zephyr-latest/boards/actinius/icarus_som_dk/doc/ |
| D | index.rst | 84 | 15 | P4 | nRF9160 P0.04 | gpio0 |
|
| /Zephyr-latest/boards/nordic/nrf52dk/doc/ |
| D | index.rst | 304 P4/P10 Digital I/O
|
| /Zephyr-latest/boards/wiznet/w5500_evb_pico/doc/ |
| D | index.rst | 119 - I2C0_SDA : P4
|
| /Zephyr-latest/boards/raspberrypi/rpi_pico/doc/ |
| D | index.rst | 121 - I2C0_SDA : P4
|
| /Zephyr-latest/boards/ezurio/bl5340_dvk/doc/ |
| D | index.rst | 145 * LED1 (blue) = via TCA9538 port expander channel P4 (active low)
|
| /Zephyr-latest/boards/ezurio/bt610/doc/ |
| D | bt610.rst | 278 | P4 | MUX A0 |
|
