Searched refs:UART1 (Results 1 – 25 of 103) sorted by relevance
12345
| /Zephyr-latest/boards/shields/nrf7002ek/boards/ |
| D | nrf5340dk_nrf5340_cpuapp.overlay | 6 /* This node by default forwards the UART1 pins to CPUNET, but as UART1 uses
|
| /Zephyr-latest/samples/net/openthread/coprocessor/boards/ |
| D | cc1352p7_lp.overlay | 11 /* Use UART1 for debugging / zephyr console */
|
| /Zephyr-latest/boards/ct/ctcc/ |
| D | ctcc_nrf9161_ns.dts | 19 /* Disable UART1, because it is used by default in TF-M */
|
| /Zephyr-latest/boards/nordic/nrf9131ek/ |
| D | nrf9131ek_nrf9131_ns.dts | 19 /* Disable UART1, because it is used by default in TF-M */
|
| /Zephyr-latest/boards/nordic/nrf9151dk/ |
| D | nrf9151dk_nrf9151_ns.dts | 19 /* Disable UART1, because it is used by default in TF-M */
|
| /Zephyr-latest/boards/nordic/nrf9160dk/ |
| D | nrf9160dk_nrf9160_ns.dts | 19 /* Disable UART1, because it is used by default in TF-M */
|
| /Zephyr-latest/boards/nordic/nrf9161dk/ |
| D | nrf9161dk_nrf9161_ns.dts | 19 /* Disable UART1, because it is used by default in TF-M */
|
| /Zephyr-latest/boards/norik/octopus_io_board/ |
| D | octopus_io_board_nrf9160_ns.dts | 18 /* Disable UART1, because it is used by default in TF-M */
|
| /Zephyr-latest/drivers/serial/ |
| D | uart_ite_it8xxx2.c | 42 UART1 = 1, enumerator
162 if (config->port == UART1) { in uart_it8xxx2_init()
|
| /Zephyr-latest/boards/particle/argon/dts/ |
| D | mesh_feather_uart1_rtscts.dtsi | 7 /* Add hardware flow control to UART1 on Feather-based mesh boards
|
| /Zephyr-latest/boards/particle/boron/dts/ |
| D | mesh_feather_uart1_rtscts.dtsi | 7 /* Add hardware flow control to UART1 on Feather-based mesh boards
|
| /Zephyr-latest/boards/particle/xenon/dts/ |
| D | mesh_feather_uart1_rtscts.dtsi | 7 /* Add hardware flow control to UART1 on Feather-based mesh boards
|
| /Zephyr-latest/tests/drivers/uart/uart_elementary/ |
| D | README.txt | 7 For dual uart configuratiom - UART0 and UART1 TXs and RXs cross-connected
|
| /Zephyr-latest/boards/arm/fvp_baser_aemv8r/ |
| D | board.cmake | 25 # UART1 config
59 # UART1 config
|
| /Zephyr-latest/samples/tfm_integration/psa_crypto/boards/ |
| D | nrf9160dk_nrf9160_ns.overlay | 34 /* Disable UART1, because it is used by default in TF-M */
|
| /Zephyr-latest/samples/tfm_integration/tfm_ipc/boards/ |
| D | nrf9160dk_nrf9160_ns.overlay | 34 /* Disable UART1, because it is used by default in TF-M */
|
| /Zephyr-latest/boards/ti/common/ |
| D | launchxl-pinctrl.dtsi | 21 /* UART1 */
|
| /Zephyr-latest/boards/nuvoton/npcx7m6fb_evb/doc/ |
| D | index.rst | 16 - UART0 and UART1
62 UART1 is configured for serial logs.
|
| /Zephyr-latest/boards/ronoth/lodev/doc/ |
| D | index.rst | 42 UART1 on the S76S SiP is connected to a USB-to-UART device connected to the micro USB connector, so…
79 18 PA9 USB serial Tx drives this pin (input) for UART1
80 19 PA10 USB serial Rx is driven by this pin (output) for UART1
|
| /Zephyr-latest/boards/nuvoton/npcx9m6f_evb/doc/ |
| D | index.rst | 16 - UART0 and UART1
76 UART1 is configured for serial logs.
|
| /Zephyr-latest/boards/arm/fvp_base_revc_2xaemv8a/ |
| D | board.cmake | 15 # UART1 config
|
| /Zephyr-latest/boards/ronoth/lodev/ |
| D | ronoth_lodev.dts | 71 <17 0 &gpioa 9 0>, /* PA9 (UART1 Rx connected to USB) */
72 <18 0 &gpioa 10 0>, /* PA10 (UART1 Tx connected to USB) */
|
| /Zephyr-latest/boards/telink/tlsr9518adk80d/ |
| D | tlsr9518adk80d-pinctrl.dtsi | 24 /* UART1: TX(PC6), RX(PC7) */
|
| /Zephyr-latest/boards/nuvoton/npcx4m8f_evb/doc/ |
| D | index.rst | 16 - UART0 and UART1
76 UART1 is configured for serial logs.
|
| /Zephyr-latest/boards/beagle/beagleconnect_freedom/ |
| D | beagleconnect_freedom-pinctrl.dtsi | 21 /* UART1 */
|
12345
