| /Zephyr-Core-3.6.0/boards/arm/particle_argon/ |
| D | board.c | 27 gpio_pin_configure_dt(&ufl_gpio, (on ? GPIO_OUTPUT_ACTIVE : GPIO_OUTPUT_INACTIVE)); in external_antenna()
28 gpio_pin_configure_dt(&pcb_gpio, (on ? GPIO_OUTPUT_INACTIVE : GPIO_OUTPUT_ACTIVE)); in external_antenna()
|
| /Zephyr-Core-3.6.0/boards/arm/particle_xenon/ |
| D | board.c | 27 gpio_pin_configure_dt(&ufl_gpio, (on ? GPIO_OUTPUT_ACTIVE : GPIO_OUTPUT_INACTIVE)); in external_antenna()
28 gpio_pin_configure_dt(&pcb_gpio, (on ? GPIO_OUTPUT_INACTIVE : GPIO_OUTPUT_ACTIVE)); in external_antenna()
|
| /Zephyr-Core-3.6.0/samples/boards/96b_argonkey/microphone/src/ |
| D | main.c | 54 gpio_pin_configure_dt(&led0, GPIO_OUTPUT_ACTIVE); in signal_sampling_started()
60 gpio_pin_configure_dt(&led0, GPIO_OUTPUT_ACTIVE); in signal_sampling_stopped()
61 gpio_pin_configure_dt(&led1, GPIO_OUTPUT_ACTIVE); in signal_sampling_stopped()
67 gpio_pin_configure_dt(&led1, GPIO_OUTPUT_ACTIVE); in signal_print_stopped()
|
| /Zephyr-Core-3.6.0/boards/arm/particle_boron/ |
| D | board.c | 26 gpio_pin_configure_dt(&ufl_gpio, (on ? GPIO_OUTPUT_ACTIVE : GPIO_OUTPUT_INACTIVE)); in external_antenna()
|
| /Zephyr-Core-3.6.0/samples/basic/blinky/src/ |
| D | main.c | 32 ret = gpio_pin_configure_dt(&led, GPIO_OUTPUT_ACTIVE); in main()
|
| /Zephyr-Core-3.6.0/soc/arm/atmel_sam0/common/ |
| D | soc_samr3x_radio_off.c | 21 ret = gpio_pin_configure_dt(&reset, GPIO_OUTPUT_ACTIVE); in radio_off_setup()
|
| /Zephyr-Core-3.6.0/samples/boards/stm32/power_mgmt/blinky/src/ |
| D | main.c | 27 gpio_pin_configure_dt(&led, GPIO_OUTPUT_ACTIVE); in main()
|
| /Zephyr-Core-3.6.0/samples/subsys/debug/debugmon/src/ |
| D | main.c | 66 int err = gpio_pin_configure_dt(&led, GPIO_OUTPUT_ACTIVE); in main()
|
| /Zephyr-Core-3.6.0/boards/arm/efr32_thunderboard/ |
| D | board.c | 35 ret = gpio_pin_configure_dt(&wake_up_gpio_dev, GPIO_OUTPUT_ACTIVE); in thunderboard_init()
|
| /Zephyr-Core-3.6.0/boards/arm/efr32xg24_dk2601b/ |
| D | board.c | 35 ret = gpio_pin_configure_dt(&wake_up_gpio_dev, GPIO_OUTPUT_ACTIVE); in efr32xg24_dk2601b_init()
|
| /Zephyr-Core-3.6.0/modules/openthread/platform/ |
| D | misc.c | 76 gpio_pin_configure_dt(&bootloader_gpio, GPIO_OUTPUT_ACTIVE); in otPlatResetToBootloader()
|
| /Zephyr-Core-3.6.0/samples/subsys/mgmt/osdp/peripheral_device/src/ |
| D | main.c | 40 ret = gpio_pin_configure_dt(&led0, GPIO_OUTPUT_ACTIVE); in main()
|
| /Zephyr-Core-3.6.0/drivers/lora/ |
| D | sx126x_standalone.c | 73 if (gpio_pin_configure_dt(&sx126x_gpio_reset, GPIO_OUTPUT_ACTIVE) || in sx126x_variant_init()
|
| /Zephyr-Core-3.6.0/samples/subsys/mgmt/osdp/control_panel/src/ |
| D | main.c | 84 ret = gpio_pin_configure_dt(&led0, GPIO_OUTPUT_ACTIVE); in main()
|
| /Zephyr-Core-3.6.0/drivers/gpio/ |
| D | gpio_hogs.c | 34 (GPIO_OUTPUT_ACTIVE), (0)))))), \
|
| D | gpio_sn74hc595.c | 167 if (gpio_pin_configure_dt(&config->reset_gpio, GPIO_OUTPUT_ACTIVE) < 0) { in gpio_sn74hc595_init()
|
| D | gpio_tle9104.c | 436 result = gpio_pin_configure_dt(&config->gpio_enable, GPIO_OUTPUT_ACTIVE); in tle9104_init()
449 result = gpio_pin_configure_dt(&config->gpio_reset, GPIO_OUTPUT_ACTIVE); in tle9104_init()
|
| /Zephyr-Core-3.6.0/samples/boards/stm32/power_mgmt/standby_shutdown/src/ |
| D | main.c | 147 gpio_pin_configure_dt(&led, GPIO_OUTPUT_ACTIVE); in main()
|
| /Zephyr-Core-3.6.0/drivers/can/transceiver/ |
| D | can_transceiver_gpio.c | 102 err = gpio_pin_configure_dt(&config->standby_gpio, GPIO_OUTPUT_ACTIVE); in can_transceiver_gpio_init()
|
| /Zephyr-Core-3.6.0/samples/boards/stm32/power_mgmt/suspend_to_ram/src/ |
| D | main.c | 137 gpio_pin_configure_dt(&led, GPIO_OUTPUT_ACTIVE); in main()
|
| /Zephyr-Core-3.6.0/drivers/sensor/current_amp/ |
| D | current_amp.c | 130 ret = gpio_pin_configure_dt(&config->power_gpio, GPIO_OUTPUT_ACTIVE); in current_init()
|
| /Zephyr-Core-3.6.0/drivers/sensor/voltage_divider/ |
| D | voltage.c | 136 ret = gpio_pin_configure_dt(&config->gpio_power, GPIO_OUTPUT_ACTIVE); in voltage_init()
|
| /Zephyr-Core-3.6.0/drivers/mdio/ |
| D | mdio_gpio.c | 41 gpio_pin_configure_dt(&dev_cfg->mdio_gpio, dir ? GPIO_OUTPUT_ACTIVE : GPIO_INPUT); in mdio_gpio_dir()
|
| /Zephyr-Core-3.6.0/boards/arm/nrf9160dk_nrf52840/ |
| D | board.c | 176 flags |= (cfg->on ? GPIO_OUTPUT_ACTIVE in init()
|
| /Zephyr-Core-3.6.0/drivers/input/ |
| D | input_ft5336.c | 163 r = gpio_pin_configure_dt(&config->reset_gpio, GPIO_OUTPUT_ACTIVE); in ft5336_init()
|
