Searched refs:polarity (Results 1 – 17 of 17) sorted by relevance
| /Zephyr-Core-3.4.0/samples/sensor/qdec/boards/ |
| D | nucleo_f401re.overlay | 22 st,input-polarity-inverted;
|
| /Zephyr-Core-3.4.0/drivers/counter/ |
| D | counter_mcux_lptmr.c | 21 lptmr_pin_polarity_t polarity; member
135 lptmr_config.pinPolarity = config->polarity; in mcux_lptmr_init()
224 .polarity = DT_INST_PROP(0, active_low),
|
| /Zephyr-Core-3.4.0/drivers/gpio/ |
| D | gpio_b91.c | 71 uint8_t polarity; /* Polarity: interrupt polarity: rising, falling */ member
185 BM_CLR(gpio->polarity, BIT(pin)); in gpio_b91_irq_set()
190 BM_SET(gpio->polarity, BIT(pin)); in gpio_b91_irq_set()
195 BM_CLR(gpio->polarity, BIT(pin)); in gpio_b91_irq_set()
200 BM_SET(gpio->polarity, BIT(pin)); in gpio_b91_irq_set()
|
| D | gpio_mcux_lpc.c | 302 pin_config.polarity = kGPIO_PinIntEnableHighOrRise; in gpio_mcux_lpc_module_interrupt_cfg()
304 pin_config.polarity = kGPIO_PinIntEnableLowOrFall; in gpio_mcux_lpc_module_interrupt_cfg()
|
| D | gpio_sx1509b.c | 46 uint16_t polarity; /* 0x0C */ member
259 pin_buf.pins.polarity = sys_cpu_to_be16(pins->polarity); in write_pin_state()
|
| /Zephyr-Core-3.4.0/samples/boards/nrf/nrfx/src/ |
| D | main.c | 97 .polarity = NRF_GPIOTE_POLARITY_TOGGLE, in main()
|
| /Zephyr-Core-3.4.0/dts/arm/nuvoton/npcx/npcx7/ |
| D | npcx7-pinctrl.dtsi | 346 psl-polarity = <&altd_psl_in1_ahi>;
352 psl-polarity = <&altd_psl_in2_ahi>;
358 psl-polarity = <&altd_psl_in3_ahi>;
364 psl-polarity = <&altd_psl_in4_ahi>;
|
| /Zephyr-Core-3.4.0/include/zephyr/drivers/usb_c/ |
| D | usbc_tcpc.h | 142 int (*set_cc_polarity)(const struct device *dev, enum tc_cc_polarity polarity);
537 enum tc_cc_polarity polarity) in tcpc_set_cc_polarity() argument
545 return api->set_cc_polarity(dev, polarity); in tcpc_set_cc_polarity()
|
| /Zephyr-Core-3.4.0/dts/arm/nuvoton/npcx/npcx9/ |
| D | npcx9-pinctrl.dtsi | 354 psl-polarity = <&altd_psl_in1_ahi>;
360 psl-polarity = <&altd_psl_in2_ahi>;
366 psl-polarity = <&altd_psl_in3_ahi>;
372 psl-polarity = <&altd_psl_in4_ahi>;
|
| /Zephyr-Core-3.4.0/samples/sensor/qdec/ |
| D | README.rst | 43 st,input-polarity-inverted;
|
| /Zephyr-Core-3.4.0/drivers/usb_c/tcpc/ |
| D | ucpd_stm32.c | 452 enum tc_cc_polarity polarity) in ucpd_cc_set_polarity() argument
466 if (polarity == TC_POLARITY_CC1) { in ucpd_cc_set_polarity()
468 } else if (polarity == TC_POLARITY_CC2) { in ucpd_cc_set_polarity()
|
| /Zephyr-Core-3.4.0/drivers/spi/ |
| D | spi_mcux_flexcomm.c | 223 master_config.polarity = in spi_mcux_configure()
264 slave_config.polarity = in spi_mcux_configure()
|
| /Zephyr-Core-3.4.0/boards/arm/reel_board/doc/ |
| D | index.rst | 451 3.3V, there is no protection against reverse polarity or overvoltage.
|
| /Zephyr-Core-3.4.0/doc/releases/ |
| D | release-notes-2.2.rst | 150 for specifying the polarity of the PWM signal. The flags parameter
|
| D | release-notes-2.3.rst | 1111 * :github:`23692` - drivers: ublox-sara-r4: Add support for pin polarity
|
| D | release-notes-2.4.rst | 897 * :github:`28665` - boards b_l4s5i_iot01a: invertion of user LEDS polarity
|
| D | release-notes-3.3.rst | 840 * Atmel SAM: Added support to select pin polarity
|
