1 /* 2 * Copyright (c) 2020 Seagate Technology LLC 3 * 4 * SPDX-License-Identifier: Apache-2.0 5 */ 6 7 /** 8 * @file Describe the IAP commands interface on NXP LPC11U6x MCUs. 9 * 10 * The IAP (In-Application Programming) commands are located in the boot ROM 11 * code. Mostly they provide access to the on-chip flash and EEPROM devices. 12 * 13 * @note For details about IAP see the UM10732 LPC11U6x/E6x user manual, 14 * chapter 27: LPC11U6x/E6x Flash/EEPROM ISP/IAP programming. 15 */ 16 17 #ifndef LPC11U6X_IAP_H_ 18 #define LPC11U6X_IAP_H_ 19 20 /* Pointer to IAP function. */ 21 #define IAP_ENTRY_ADDR 0X1FFF1FF1 22 23 /* IAP commands. */ 24 #define IAP_CMD_FLASH_PREP_SEC 50 25 #define IAP_CMD_FLASH_WRITE_SEC 51 26 #define IAP_CMD_FLASH_ERASE_SEC 52 27 #define IAP_CMD_FLASH_BLANK_CHECK_SEC 53 28 #define IAP_CMD_READ_PART_ID 54 29 #define IAP_CMD_READ_BOOT_CODE_VER 55 30 #define IAP_CMD_MEM_COMPARE 56 31 #define IAP_CMD_REINVOKE_ISP 57 32 #define IAP_CMD_READ_UID 58 33 #define IAP_CMD_FLASH_ERASE_PAGE 59 34 #define IAP_CMD_EEPROM_WRITE 61 35 #define IAP_CMD_EEPROM_READ 62 36 37 /* IAP status codes. */ 38 #define IAP_STATUS_CMD_SUCCESS 0 39 #define IAP_STATUS_INVALID_CMD 1 40 #define IAP_STATUS_SRC_ADDR_ERROR 2 41 #define IAP_STATUS_DST_ADDR_ERROR 3 42 #define IAP_STATUS_SRC_ADDR_NOT_MAPPED 4 43 #define IAP_STATUS_DST_ADDR_NOT_MAPPED 5 44 #define IAP_STATUS_COUNT_ERROR 6 45 #define IAP_STATUS_INVALID_SECTOR 7 46 #define IAP_STATUS_SECTOR_NOT_BLANK 8 47 #define IAP_STATUS_SECTOR_NOT_PREPARED 9 48 #define IAP_STATUS_COMPARE_ERROR 10 49 #define IAP_STATUS_BUSY 11 50 51 /** 52 * @brief Entry function for IAP commands. 53 */ iap_cmd(unsigned int cmd[5])54static inline int iap_cmd(unsigned int cmd[5]) 55 { 56 int key; 57 int status[5]; 58 59 /* 60 * Interrupts must be disabled when calling IAP. Indeed when executing 61 * "some" commands, the flash (where the interrupt vectors are located) 62 * is no longer accessible. 63 */ 64 key = irq_lock(); 65 66 /* 67 * TODO: for the flash commands, the top 32 bytes of memory must be 68 * saved before calling the IAP function, and restored after. According 69 * to the UM10732 user manual, the IAP code may use them. 70 */ 71 ((void (*)(unsigned int[], unsigned int[])) 72 IAP_ENTRY_ADDR)(cmd, status); 73 74 irq_unlock(key); 75 76 return status[0]; 77 } 78 79 #endif /* LPC11U6X_IAP_H_ */ 80
